• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.11a
• /
• pp.142.2-142.2
• /
• 2007

• Clean Technology
• /
• v.26 no.4
• /
• pp.329-335
• /
• 2020

Methanol synthesized from renewable hydrogen and captured CO2 has recently attracted great interest as a sustainable energy carrier for large-scale renewable energy storage. In this study, molten carbonate fuel cell's performance was investigated with the direct conversion of methanol into syngas inside the anode chamber of the cell. The internal reforming of methanol may significantly improve system efficiency since the heat generated from the electrochemical reaction can be used directly for the endothermic reforming reaction. The porous Ni-10 wt%Cr anode was sufficient for the methanol steam reforming reaction under the fuel cell operating condition. The direct supply of methanol into the anode chamber resulted in somewhat lower cell performance, especially at high current density. Recycling of the product gas into the anode gas inlet significantly improved the cell performance. The analysis based on material balance revealed that, with increasing current density and gas recycling ratio, the methanol steam reforming reaction rate likewise increased. A methanol conversion more significant than 90% was achieved with gas recycling. The results showed the feasibility of electricity and syngas co-production using the molten carbonate fuel cell. Further research is needed to optimize the fuel cell operating conditions for simultaneous production of electricity and syngas, considering both material and energy balances in the fuel cell.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.239-244
• /
• 2019

Two hydrogenation surface modifications, namely hydrogen atmosphere heat treatment and hydrogen plasma treatment, were found to lead to improved dispersion of nanodiamond (ND) seed particles and enhanced nucleation density for deposition of smooth ultrananocrystalline diamond (UNCD) film. After hydrogenation, the C-O and O-H surface functionalities on the surface of nanodiamond particles were converted to the C-H surface functionalities, and the Zeta potential was increased. As the degree of dispersion was improved, the size of nanodiamond aggregates decreased significantly and nucleation density increased dramatically. After hydrogen heat treatment at 600℃, average size of ND particles was greatly reduced from 3.5 ㎛ to 34.5 nm and a very high nucleation of ~3.9 × 10¹¹ nuclei/㎠ was obtained for the seeded Si surface.

• Journal of the Korean Institute of Gas
• /
• v.20 no.5
• /
• pp.27-33
• /
• 2016

The aim of numerical study is the investigation of the solid and fluid temperatures in a reformer tube and chemical reaction characteristics of different steam-carbon ratio. We considered conjugate heat transfer contain radiation, convection and conductive heat transfers. This is because steam reforming reaction of hydrocarbon occurred high temperature conditions up to 800 K- 1000 K by using commercial computational fluid dynamics (CFD) code (Fluent ver. 13.0). For numerical simulation, the Reynolds-Averaged Navier-Stokes, momentum and energy equation were employed. In addition, inside of reformer tube is assumed as the porous medium to consider the Nichrome-based catalyst. To analysis characteristics of tube temperature in chemical reaction, we changed steam-methane ratio(SCR) from 1 to 6. As increased SCR, the higher tube temperature and methane conversion were observed. It was obtained that the highest hydrogen production held in SCR of 5.

• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.720-726
• /
• 2014

PEM fuel cell vehicles have been getting much attraction due to a sort of highly clean and effective transportation. The onboard fuel processor, however, is inevitably required to supply the hydrogen by conversion from some fuels since there are not enough available hydrogen stations nearby. A lot of studies have been focused on analyses of ATR reactor under the assumption of thermo-neutral condition and those of the optimized process for the minimization of energy consumption using thermal efficiency as an objective function, which doesn't guarantee the maximum hydrogen production. In this study, the analysis of optimization for 100 kW PEMFC onboard fuel processor was conducted targeting various fuels such as gasoline, LPG, diesel using newly defined hydrogen efficiency and keeping simply synthesized heat exchanger network regardless of external utilities leading to compactness and integration. Optimal result of gasoline case shows 9.43% reduction compared to previous study, which shows the newly defined objective function leads to better performance than thermal efficiency in terms of hydrogen production. The sensitivity analysis was also done for hydrogen efficiency, heat recovery of each heat exchanger, and the cost of each fuel. Finally, LPG was estimated as the most economical fuel in Korean market.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.12
• /
• pp.1268-1272
• /
• 2008

Low temperature plasma applied with partial oxidation is a technique to produce synthesis gas from methane. Low temperature plasma reformer has superior miniaturization and start-up characteristics to reformers using steam reforming or CO$_2$ reforming. In this research, a low temperature plasma reformer using GlidArc discharge was proposed. Reforming characteristics for each of the following variables were studied: gas components ratio (O$_2$/CH$_4$), the amount of steam, comparison of reaction on nickle and iron catalysts and the amount of CO$_2$. The optimum conditions for hydrogen production from methane was found. The maximum Hydrogen concentration of 41.1% was obtained under the following in this condition: O$_2$/C ratio of 0.64, total gas flow of 14.2 L/min, catalyst reactor temperature of 672$^{\circ}C$, the amount of steam was 0.8, reformer energy density of 1.1 kJ/L with Ni catalyst in the catalyst reactor. At this point, the methane conversion rate, hydrogen selectivity and reformer thermal efficiency were 66%, 93% and 35.2%, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.638-641
• /
• 2005

수소는 자원이 무한하고 청결한 에너지이다. 수소는 무공해 청정 대체연료로 사용될 수 있을 뿐만 아니라 풍부한 자원으로부터 얻을 수 있다. 수소에너지는 물을 분해하여 얻거나 화석연료를 수증기개질 또는 부분산화 시킴으로써 얻을 수가 있다. 수소에너지는 1차 에너지를 변환시켜 얻을 수 있는 2차 에너지로서 환경에 대한 부하가 거의 없어 향후 화석연료를 대체할 수 있는 가장 가능성이 높은 에너지이며, 연료전지의 상용화를 앞두고 있어 중요성이 더욱 증대되고 있다. 수소를 생산하는 방법 중 가장 이상적인 방법으로는 물분해함으로써 수소를 제조하는 방법이 있다. 그러나 물분해에 의한 수소생산은 제조비용이 비싸 경제성이 떨어진다는 점과 수소의 대량생산에 필요한 기술확보가 여의치 않아 어렵다. 그러므로 수소를 저 비용으로 대량 생산할 수 있는 수소 제조 기술의 확보가 선행되어야 할 것이다. 현재 상용화되어 있는 수소제조방법은 거의 석유나 천연가스의 수증기 개질에 의한 수소 제조 방법이다. 그러나 이러한 방법은 유해 환경 물질인 CO나 $CO_2$를 배출하는 단점을 지니고 있다. 이러한 단점을 보완키 위한 수소 제조공정의 대안 중 하나는 탄화수소연료의 수소와 탄소로의 직접분해에 의한 수소생산이다. 이 중 원하는 생성물인 수소 외에 부산물이 카본이 동시에 얻을 수 있는 메탄분해에 의한 수소생산방법은 생산된 수소의 약 15%만 연소시킴으로서 필요한 에너지를 공급할 수 있으며, 동시에 지구온난화의 주범인 CO 또는 $CO_2$가 생성되지 않는 장점이 있다. 하지만 메탄을 분해하기 위해서는 매우 높은 에너지가 필요로 하게 된다. 이에 반해 프로판은 메탄보다 낮은 열원에서 분해할 수 있는 장점을 지니고 있다. 본 연구에서는 메탄보다 분해하기 쉬운 프로판을 직접 분해하여 수소를 생산하고자 하였다. 프로판 직접분해반응는 $500\sim750^{\circ}C$의 온도 범위에서 이루어 졌으며, 촉매로서는 국내에서 생산되는 상용촉매인 카본블랙을 이용하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.375-381
• /
• 2010

In this paper, the heat-transfer characteristics of steam reforming in an annular reactor are presented. Heat is supplied by the catalytic combustion of syn-gas. The thermal behaviors of exothermic and endothermic reactions in a directly coupled concentric-tube packed-bed reactor were investigated experimentally. The gas mixture supplied for catalytic combustion consisted of the off-gas emitted from MCFC anode. Methane in steam at a suitable S/C (steam-to-carbon) ratio was used in the reforming reactions. On the basis of the experimental results, a simple simulation was performed to predict the temperature profile required in the reforming side of the reactor to achieve optimum hydrogen yield. The results of this study may be utilized as reference data in future studies for further development of coupled reactors.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.4
• /
• pp.464-480
• /
• 2007

There are several methods for the hydrogen production such as steam reforming of natural gas, photochemical method, biological method, electrolysis and thermochemical method, etc. These days it has been widely studied for the hydrogen production method having low hydrogen production cost and high efficiency. In this paper, patents in the hydrogen production by steam reforming of natural gas were gathered and analyzed. The search range was limited in the open patents of USA(US), European Union(EP), Japan(JP), and Korea(KR) from 1996 to 2006. Patents were gathered by using key-words searching and extracted by filtering criteria. The trends of the patents was analyzed by the years, countries, companies, and technologies.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.5
• /
• pp.453-458
• /
• 2017

A study on the modeling of the methane Chemical Looping Reforming system was carried out. It is aimed to predict the temperature and concentration behavior of the product through modeling of oxygen carrier fixed bed reactors composed of multiple stacks. In order to design the reaction system, first of all, the flow rate of the hydrogen to be produced was calculated. The flow rate ratio of the oxidation/reduction reactor was calculated considering the heat of reaction between adjacent reactors. Finally, in this paper, kinetic model including empirical coefficients was suggested.