• Journal of Korean Society of Steel Construction
• /
• v.9 no.4 s.33
• /
• pp.683-695
• /
• 1997

This paper presents the shear behavior of panel zone in steel frame piers. The results of loading tests on twenty box connections and three types of analysis model are reported herein. It is indicate that the major cause of the reduction of strength and shear deformation capacity (ductility) is the sectional-area ratio and the shear buckling of panel zone. Based on the results, some new proposals are presented for the evalution of strength and ductility of panel zone. This paper is also discussed the ductility of connections by current design procedure.

• Journal of the Korean Society for Railway
• /
• v.9 no.1 s.32
• /
• pp.125-130
• /
• 2006

고속철도 교량구간에 차량(KTS)이 주행할 경우 교량 바닥판에서는 큰 가속도 응답이 계측된다. 이러한 가속도의 원인으로는 큰 단면의 국부 진동, 일정한 간격의 침목의 충격 그리고 차량 자체의 진동 등 여러 가지 원인이 있다. BRDM(Bridge Design manual)에서는 이러한 동적 특성치들에 대한 제한치를 규정하고 있는데, 가속도인 경우는 0.35G이하고 규정하고 있다. 실교량 실험에 의해 계측된 가속도 응답은 규정한 제한치인 0.35G 보다는 작지만, 이러한 가속도 응답치들은 차량이 고속으로 주행할 경우 안전성에 문제를 일으킬 수 있다. 본 논문에서는 큰 단면에서 과도한 국부 진동을 지배하는 가속도 응답을 줄이기 위해서 진동저감 방법을 연구하였다. 비록 휨이나 비틀림 같은 전체 진동모드에는 효과가 작지만 일반적으로 매우 큰 단면을 가진 고속철도 프리스트레스트 상자형 교량의 국부진동인 날개짓 모드를 감소시키는데 진동저감 장치는 효과적이라고 판단된다. 실교량에서 진동저감장치의 실험은 추후 연구를 수행할 예정이다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.2
• /
• pp.234-241
• /
• 1999

본 논문에서는 얇은 직사각형 단면 형상을 가지는 세 가지 서로 다른 유동로 안에서 움직이는 공기버블의 변형 거동에 대한 실험을 수행하였다. 압력 차이로 유체는 유동되며, 유동장을 따라서 변형하는 버블의 정상상태 모양을 관찰하였다. 벽면효과를 알아보기 위해 세 종류의 얇은 사각단면을 사용하였으며, 두 가지 종류의 작동 유체, 버블의 초기 크기, 작동 유체의 유량 등을 변화시켰을 때 이에 대한 공기 버블의 변형을 체계적으로 관찰하고 이들의 관계를 고찰하였다. 실험데이타를 정량화하여 캐필러리 수에 대한 버블의 무차원 속도비와의 관계를 상세하게 고찰하였다. 글리세린의 경우는 항상 버블 선단부의 곡률이 후단의 곡률보다 더 작게 나타났으며 실리콘 오일의 경우와 반대 경향이 관찰되었다. 두 경우 모두 캐필러리 수에 대한 속도비와 세장비 값은 1 보다 큰 값을 가졌다. 실리콘 오일의 경우는 주어진 Ca 수에 대하여 속도비가 글리세린의 경우보다 더 크게 나왔으며 버블 크기에 따른 속도비 분산도가 더 조밀하게 나타났다. 사각 단면 폭이 감소할수록 벽면 효과는 증대되었으며 같은 폭에 대해서는 버블 변형이 축소관의 경우가 가장 크게 나타났다.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.23-30
• /
• 2011

본 연구는 산업용 열교환기 및 상용 파이프의 최적 설계를 위하여 열교환기 내의 사각형 단면 파이프의 shear-thickening 비뉴톤 유체의 압력강하 및 대류 열전달률을 수치해석적으로 수행하였다. shear-thickening 유체의 구성 방정식은 기존의 비뉴톤 유체 멱법칙을 보완한 확장 멱법칙 모델을 채택하였다. 파이프 내의 압력강하를 의미하는 마찰계수와 확장 레이놀즈 수의 곱은 기존 연구의 비교자료와 비교할 때 뉴톤 유체 영역과 멱법칙 영역에서 각각 0.018% 및 0.06% 내에서 일치함을 보였고, 대류 열전달률을 의미하는 뉴셀트 수는 문헌치와 비교할 때 뉴톤 유체 영역과 멱법칙 영역에서 각각 0.025% 및 0.14% 내에서 일치함을 보였다. 비뉴톤 확장 멱법칙 유체 모델의 형태를 띠는 shear-thickening 유체를 열교환기 또는 상용파이프 내의 사각형 단면 파이프 내에서 사용하면 유동지수(n)에 따라서 뉴톤 유체보다 최대 160%의 압력강하를 증가시켰고 최대 14%의 대류 열전달 감소를 발생시킬 수 있었다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.2
• /
• pp.41-54
• /
• 1999

Because of relatively heavy dead weight of concrete itself and unavoidable heat of massive concrete in bridge piers, circular hollow columns are widely used in Korean highway bridges. Since the occurrence of 1995 Kobe earthquake, there have been much concerns about seismic design for various infrastructures, inclusive of bridge structures. It is, however, understood that there are not much research works for nonlinear behavior of circular hollow columns subjected to eqrthquake motions. The objective of this experimental research is to investigate nonlinear behavior of circular hollow reinforced concrete bridge piers under the quasi-static cyclic load, and then to enhance their ductility by strengthening the plastic hinge region with glassfiber sheets. Particularly for this test, constant 10 cyclic loads have been repeatedly actuated to investigate the magnitude of strength degradation for the displacement ductility factor. Important test parameters are seismic design, confinement steel ratio, axial force and load pattern. It is observed from quasi-static tests for 7 bridge piers that the seismically designed columns and the retrofitted columns show better performance than the nonseismically designed colums, i.e. about 20% higher for energy dissipation capacity and about 70% higher for curvatures.

• Journal of Korean Society of Disaster and Security
• /
• v.15 no.3
• /
• pp.67-77
• /
• 2022

In South Korea, U-type girder development was attempted as a means to increase the length of I-type girder, but due to the large self-weight according to the post-tension method, the application of rail bridges of 30m or less is typical. There are not many examples of application of pre-tension type girder. This study does not limit the post-tension method, but applies the pre-tension method to induce a reduction in self-weight and materials used due to the reduction of the cross-section. In addition, we intend to apply the on-site pre-tensioning method using the internal reaction arm of the U-type girder. The prestressed concrete U-type girder bridge is composed of a concrete deck slab and a composite section. Compared to the PSC I-type, which is an open cross-section because the cross section is closed, structural performance such as resistance and rigidity is improved, the safety of construction is increased during the manufacturing and erection stage, and the height ratio is reduced due to the reduction of its own weight. Therefore, it is possible to secure the aesthetic scenery and economical of the bridge. As a result, it is expected that efficient construction will be possible with high-quality factory-manufactured members and cast-in-place members. In this paper, the introduction of the pre-tension method on-site and the analytical performance verification of the anchoring block for tension are included.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.5
• /
• pp.377-387
• /
• 2016

In recent, in case that the underpass is constructed by trenchless method, its stability increases by reinforcing steel pipe with re-bar and mortar after propulsion into the ground to form pipe-roof. Therefore, it can be predicted that the integrated pipe-roof decreases the stress acting on the underpass by sharing load. In this study, to analyze the effect of integrated pipe-roof and behavior of stress around underpass, experimental tests for the rectangular and arch cross section of the underpass are performed using soil chamber. As a result, stress and strain acting on the underpass decrease due to sharing load by integrated pipe-roof. This phenomenon is more pronounced by increasing the stiffness of pipe-roof. Furthermore it can be expected that cross-section of underpass can be economically designed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.2
• /
• pp.47-53
• /
• 2014

The paper investigates the limit state of deflection for short and medium span steel girder bridges. Deflection depends on stiffness of steel girders and integrity of the reinforced concrete slab (composite action). Load and resistance parameters are treated as random variables. A probabilistic model is developed for prediction of the deflection. The structural performance can be affected by deterioration of components, in particular corrosion of steel girders. In addition, the creep of concrete can greatly influence the deflection of composite structures. Therefore, the statistical models for creep and corrosion of structural steel are incorporated in the model. Structures designed according to the AASHTO LRFD Code are considered. Load and resistance models are developed to account for time-variability of the parameters. Monte Carlo simulations are used to estimate the deflections and probabilities of serviceability failure. Different span lengths and girder spacing are considered for structures designed as moment-controlled and deflection-controlled. A summary of obtained results is presented.

• Computational Structural Engineering
• /
• v.9 no.3
• /
• pp.199-207
• /
• 1996

When an initially straight thin cylinder is bent, there is a tendency for the cross section to flatten. This phenomenon was investigated by L.G. Brazier in 1927 and is called "Brazier Effect" or "Brazier Theory". The main characteristic is the reduction of carrying capacity due to the decrease of bending stiffness by shortening of thickness with the increase of external load. And the relationship of curvature-bending moment becomes a soft spring type as shown in Fig.2. In this paper, the Brazier theory on plate type structures is investigated from the following view points : (1) What is the Brazier effect? (2) the reason of the occurrence of the Brazier effect in plate type structures by using beam model and (3) factors which cause the brazier effect.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.1
• /
• pp.77-84
• /
• 2007

In this paper presented, a design method of sandwich slab bridge of simple supported made by composite materials. Many of the bridge systems, including the girders and cross-beams, and concrete decks behave as the special orthotropic plates. Such systems with sections, boundary conditions other than Navier or Levy solution types, or with irregular cross sections, analytical solution is very difficult to obtain. Thus, Finite Difference Method is used for analysis of the pertinent problem. For the design of bridge made by the composite materials, cross-section is used the form-core shape because of this shape is economical and profitable, and for output of the stress value used F.D.M. Based the experimental of a composite specialist, an equation expressing the rate of decrease of tensile strength of glass fibers based on increase of mass was obtained. From these equations, one can estimate the rate of tensile strength reduction due to increased size. Tasi-Wu failure criterion for stress space is used. Strength-failure analysis procedure, using these reduced tensile strength, is presented.