• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2016.11a
• /
• pp.353-356
• /
• 2016

불투수성 방수아스팔트는 아스팔트 혼합물이 골재와 골재 사이를 강력하게 부착하며, 골재간의 공간을 메우고, 골재표면을 두껍게 코팅하여 골재 상호간의 강한 접착을 유지시켜주는 열가소성 폴리머를 사용한 포장공법이다. 이러한 불투수성 아스팔트는 기존의 가열식 일반아스팔트 공법에서 문제시 되고 있는 내구성 저하와 잦은 유지보수로 인한 문제점을 해결할 수 있는 공법으로 차세대 고내구성 포장공법으로 주목을 받고 있다. 본 연구는 불투수성 방수아스팔트 혼합물 개발을 위한 연구의 일환으로 상온과 영하 $10^{\circ}C$의 조건하에서 기존 아스팔트수지와 새로운 개념의 불투수성 고분자계 수지의 부착성능 비교 검토하였으며, 아스팔트혼합물의 부착성능도 실험을 통해 비교 하였다. 실험결과 불투수성 아스팔트의 부착성능이 기존 아스팔트에 비해 상온은 물론 저온에서도 뛰어난 성능을 발휘하는 것을 확인 하였다.

• Resources Recycling
• /
• v.9 no.3
• /
• pp.37-45
• /
• 2000

This paper presents the experimental test results on moisture and freeze-thaw resistance of hot mix crumb rubber modified (CRM) asphalt concrete mixture. To compare the differences in mechanical properties of conventional and CRM asphalt concretes, various tests were conducted under different moisture conditions and freeze-thaw cycles. Marshall mix design was also performed to determine the optimum asphalt contents for the both asphalt concrete mixtures. Test results revealed that the moisture and freeze-thaw resistance of CRM asphalt mixture was superior to the conventional asphalt concrete. As a result, it is considered that the utilization of waste tires in asphalt pavements has the potential of minimizing the damage due to the moisture and freeze-thaw.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.1-12
• /
• 2009

A new mix design procedure for cold in-place recycling using foamed asphalt (CIR-foam) has been developed for Iowa Department of Transportation. Some strengths and weaknesses of the new mix design parameters were considered and modified to improve the laboratory test procedure. Based on the critical mixture parameters identified, a new mix design procedure was developed and validated to establish the properties of the CIR-foam mixtures. As part of the validation effort to evaluate a new CIR-foam mix design procedure, dynamic moduli of CIR-foam mixtures made of seven different reclaimed asphalt pavement (RAP) materials collected throughout the state of Iowa were measured and their master curves were constructed. The main objectives of this study are to provide: 1) standardized testing procedure for measuring the dynamic modulus of CIR-foam mixtures using new simple performance testing (SPT) equipment; 2) analysis procedure for constructing the master curves for a wide range of RAP materials; and 3) impacts of RAP material characteristics on the dynamic modulus. Dynamic moduli were measured at three different temperatures and six different loading frequencies and they were consistent among different RAP sources. Master curves were then constructed for the CIR-foam mixtures using seven different RAP materials. Based upon the observation of the constructed master curves, dynamic moduli of CIR-foam mixtures were less sensitive to the loading frequencies than HMA mixtures. It can be concluded that at the low temperature, the dynamic modulus is affected by the amount of fines in the RAP materials whereas, at the high temperature, the dynamic modulus is influenced by the residual binder characteristics.

• 한국방재학회:학술대회논문집
• /
• 2009.02b
• /
• pp.81.1-81.1
• /
• 2009

• Land and Housing Review
• /
• v.13 no.4
• /
• pp.125-134
• /
• 2022

Reclaimed aggregates through waste asphalt are produced and utilized for waste resource utilization. This study conducts quality tests and performance evaluations for mixtures with Rejuvenator applied to reclaimed asphalt concrete. Through quality testing and performance evaluation, the study investigates whether there is any problem in using reclaimed asphalt concrete by replacing general hox mix asphalt. As a result, the values of ordinary hot mix asphalt are similar to those of reclaimed asphalt, suggesting that the substitution does not create critical engineering issues. Using reclaimed asphalt concrete has the advantages of increasing economic efficiency and utilizing waste resources.

• International Journal of Highway Engineering
• /
• v.13 no.1
• /
• pp.41-48
• /
• 2011

Warm-Mix Asphalt(WMA) mixtures, which meet environmental protection and have high energy efficiency, are emerging as an alternative to hot-mix asphalt mixtures. The objective of this study is to evaluate WMA made with Aspha-min in the laboratory and to compare the design results accomplished by new Mechanistic-Empirical Pavement Design Guide(MEPDG) with control mixture. An asphalt mixture with a nominal maximum size of 12.5mm and PG64-28 binder was used. Resilient modulus tests for a control mixture and WMA with 0.3% and 0.5% of Aspha-min were conducted. The results obtained by MEPDG after inputting the test output into the design indicated that the predicted rut depth of WMA using Aspha-min was much lower than that of control mixture, and showed that WMA was more resistant to rutting than control mixture.

• 한국도로학회:학술대회논문집
• /
• 2000.11a
• /
• pp.61-67
• /
• 2000

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.6D
• /
• pp.803-810
• /
• 2011

The public interest of global warming and energy shortage is gradually increased, and the related industries also have become interested in developing eco-friendly material and technology. Warm-mix asphalt (WMA) is a result of the developments to alleviate global warming and energy problems. This WMA is produced at lower temperatures than the temperature at which hot mix asphalt (HMA) is produced. Because most tests in Superpave are developed only for the performance and maintenance of HMA produced by hot temperatures, it is difficult for the tests to identify properly the material properties and then evaluate the performances between HMA and WMA. This study deals with the development of a new protocol to differentiate HMA and WMA performance, and especially the interfacial properties between asphalt and aggregate are targeted as the performance indicator; thus, an evaluation method and guideline are suggested. The concept and idea of the test method applied in this study were modified from the DSR moisture damage test protocol. In addition, TSR test was performed to affirm the relation between the asphalt-aggregate interface and the asphalt-aggregate mixture performances. The followings are the results of this study. Shear stress at 85% linear visco-elastic complex modulus (LVE $G^*$) can be a better parameter than LVE $G^*$, which can assess the interfacial or bonding performance between asphalt and aggregate. Moreover, measuring the bonding performance in thinner film thicknesses will be a better way to evaluate the real and field situation between asphalt and aggregate. The interfacial properties' criteria to apply the newly developed test and parameter should be developed, after the asphalt mixture criteria relating to the interfacial properties are completed.

• 한국도로학회지:도로
• /
• v.5 no.3 s.17
• /
• pp.27-31
• /
• 2003

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.4
• /
• pp.489-495
• /
• 2016

In this study, the Warm-Mix Asphalt was prepared using a modified Sulfur Binder mixed with an additive of a polymer component in sulfur, which is an industrial by-product generated in the crude oil refining process. The dynamic stability and durability characteristics of the prepared Warm-Mix Asphalt was evaluated by the indirect tensile strength, the tensile strength ratio before and after water immersion and freezing-thawing, and the dynamic stability by wheel tracking test. The Warm-Mix Asphalt Mixtures using Modified Sulfur Binder has a tensile strength ratio before and after water immersion of 0.88, which is about 1.13 times that of the Warm-Mix formed modified Asphalt, and the tensile strength ration before and after freezing-thawing is also 0.82, thus, all tensile strength ratios satisfied the KS quality standard value of 0.75 or more. The indirect tensile strength was 1.6MPa which was twice the KS quality standard value of 0.8MPa, and about 1.24 times higher than that of normal heated asphalt 1.29MPa. In addition, the dynamic stability by the wheel tracking test was 14,075 times/mm, which was about 15 times higher than that of normal heated asphalt and about 3 times higher than that of the Warm-Mix formed modified Asphalt, showing excellent resistance to plastic deformation such as fatigue cracks.