• Journal of the Korean Vacuum Society
• /
• v.16 no.2
• /
• pp.153-159
• /
• 2007

In-cryostat helium lines are under installation to transfer a cryogenic helium into cold components in KSTAR device. In KSTAR, three kinds of helium should be supplied into the cold components, which are supercritical helium Into superconduction(SC) magnet system, liquid helium into current lead system, and gas helium into thermal shields. Cryogenic helium lines consist of transfer lines outside the cryostat, in-cryostat helium lines, and electrical breaks. In-cryostat helium lines should be guaranteed of leak tightness for tong time operation at high internal helium pressure of 20 bar. We wrapped the helium line with multi-layer insulator(MLI) to reduce radiation heat and insulated the surface of the high potential part with prepreg tape. The electrical break was fabricated by brazing ceramic tube with stainless steel tube. To ensure the operation reliability at operation temperature, all the electrical break have been examined by the thermal cycle test at liquid nitrogen and by the hydraulic test at 30 bar. And additional surface insulation was prepared with prepreg tape to give structural safety. At present most of the in-cryostat helium lines have been installed and the final inspection test is progressing.

• Restorative Dentistry and Endodontics
• /
• v.36 no.5
• /
• pp.377-384
• /
• 2011

Objectives: The purpose of this study was to observe the change in the viscoelastic properties of thermoplasticized injectable root canal filling materials as a function of temperature and to compare the handling characteristics of these materials. Materials and Methods: Three commercial gutta perchas and Resilon (Pentron Clinical Technologies) in a pellet form were heated in the Obtura-II system (Obtura Spartan) at $140^{\circ}C$ and $200^{\circ}C$, and the extrusion temperature of the thermoplasticized materials was measured. The viscoelastic properties of the materials as a function of temperature were evaluated using a rheometer. The elastic modulus G', viscous modulus G", loss tangent tan${\delta}$, and complex viscosity ${\eta}^*$ were determined. The phase transition temperature was determined by both the rheometer and a differential scanning calorimeter (DSC). The consistency of the materials was compared under compacting pressure at $60^{\circ}C$ and $40^{\circ}C$ by a squeeze test. Results: The three gutta perchas had dissimilar profiles in viscoelastic properties with varying temperature. The phase transition of softened materials into solidification occurred at $40^{\circ}C$ to $50^{\circ}C$, and the onset temperatures obtained by a rheometer and a DSC were similar to each other. The onset temperature of phase transition and the consistency upon compaction pressure were different among the materials (p < 0.05). Resilon had a rheologically similar pattern to the gutta perchas, and was featured between high and low-flow gutta perchas. Conclusions: The rheological characteristics of the thermoplasticized root canal filling materials changed under a cooling process. The dissimilar viscoelastic properties among the materials require different handling characteristics during an injecting and compacting procedure.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.1
• /
• pp.1-9
• /
• 2018

Visibility is very poor in tunnel fire because of confined space where the fire may easily lead to the mass casuality incident because of fast smoke spread. In this test, air curtain and the fan were installed at rescue station in a bid to make use of rescue station in safe way during the train fire in undersea tunnel and a full-scale fire test was conducted to identify the applicability of air curtain system. Air curtain system was installed at a real rescue station and the test was continued for 2 minutes till heptane which was used as fire source was completely burned out. When air curtain was working, difference in temperature between inside and outside the platform was $160^{\circ}C$ and carbon monoxide measured inside the platform was less than the case of no air curtain system by 160 ppm. Thus a full-scale fire test demonstrated that the air curtain system installed at rescue station in undersea tunnel was able to effectively block the heat and smoke generated from the fire.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.109.2-109.2
• /
• 2010

세라믹 필터는 여러 종류의 분진제거 시스템에서 연소 배가스 정제를 위한 가장 적절한 소재로 알려져 있다. 현재까지 다양한 형태의 세라믹 필터가 개발되고 있는데, 캔들 타입(candle type), 튜브 타입(tubular type), 평판 타입(parallel flow type) 등이 그 예이다. 통상적으로 세라믹 캔들 필터는 가압유동층복합발전(PFBC, Pressurize Fluidized-Bed Combustion), 석탄가스화복합발전(IGCC, Integrated coal Gasification Combined Cycle), 석탄가스화연료전지복합발전(IGFC, Integrated coal Gasification Fuel cell Combined cycle)에서 고온 배가스 정제용으로 사용되고 있다. 일반적으로 IGCC나 CTL 합성가스 정제시스템의 경우에는 높은 고압(약 25기압)과 미세분진이 함유되어 있는 분위기에서 운전된다. 그러므로 이때 사용되는 초청정용 세라믹 집진필터는 고온, 고압 및 부식 환경에서 50 MPa 이상을 갖는 높은 강도와 내식성을 갖도록 개발되어야 하기 때문에 SiC(Silicon Carbide)가 가장 적절한 캔들 필터 소재로 적용되고 있다. 이에 따라 집진용 SiC 세라믹 캔들 필터를 개발하기 위해서는 고온에서 내산화성이 우수하고, 부피팽창에 의한 균열이 발생하지 않는 무기결합재의 선정 및 이를 통한 소재의 특성 최적화가 가장 중요한 부분이라 할 수 있다. 본 연구에서는 IGCC나 CTL 공정에 적용하기 위한 SiC 캔들 필터 소재 개발을 위해 래밍성형 공정으로 1m급의 탄화규소 캔들 필터 시작품을 제작하여 SiC 출발입자 크기와 무기계 결합재인 스트론튬 카보네이트의 첨가량 변화에 따른 필터 소재의 특성 평가를 수행하였다.

• Journal of Aerospace System Engineering
• /
• v.13 no.6
• /
• pp.9-16
• /
• 2019

The experiment on the liquid jet in crossflow in supersonic BFS (backward-facing step) flow was conducted to investigate the mixing characteristics. The working fluids are nitrogen and water. The shadow graph technique was used to visualize the flow field. Images captured by the high-speed camera were applied to analyze the flow phenomena. The liquid jet was injected at the re-circulation zone created by the supersonic jet flow. Experimental conditions are defined based on the pressure of the nitrogen gas chamber and pressurized liquid tank. In respective cases, the penetration depth of liquid jet and location of the Mach disc were observed to be proportional to the momentum ratio of gas and liquid jets.

• Journal of Energy Engineering
• /
• v.12 no.4
• /
• pp.289-301
• /
• 2003

To develop a chemical-looping combustion technology, conceptual design of 50 kW thermal chemical-looping combustor, which is composed of two interconnected pressurized circulating fluidized beds, was performed by means of mass and energy balance calculations. A riser type fast fluidized bed was selected as an oxidizer and a bubbling fluidized bed was selected as a reducer by mass balance for the chemical-looping combustor. Calculated values of bed mass, solid circulation flux, and reactor dimension by mass and energy balance calculations were suitable for construction and operation of chemical-looping combustor. It is concluded from the comparison of the design results and operating values of commercial circulating fluidized bed that the process outline is realistic. Moreover, the previous results support that oxygen carrier particle, NiO/bentonite, fulfills the conversion rates needed for the proposed design. The effects of system capacity, metal oxide content in a oxygen carrier particle, amount of steam input, gas velocity, and solid depth on design values were investigated and the changes in the system performance can be estimated by proposed design tool.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.4
• /
• pp.402-410
• /
• 2002

Recently the necessity of study on optical measuring method using laser to detect the pipeline's defect in nuclear facilities, chemical industries and power plants has been increased. Because laser light can be delivered to a remote area without any difficulties, the application of laser in many industries can solve several difficulties from the limitation of access in danger area and reduce the risks of workers. Therefore, we applied a new experimental technique to the measurement of internal defects in pressure vessels with the combination of shearography and image processing technique and detected the internal cracks of pressure vessels in the former paper. In this paper, we used the same optical system as in the former study and found the optimum shearing magnitude by comparing the real length of specimen with experimental results. A variety of conditions were applied to certify the validity of this method. Actually, several specimens which have different lengths and depths were used in this experiment under the three diverse pressure. Consequently, we have carried out this experiment to determine the limit of measurement ability with analyzing errors.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.71-79
• /
• 2014

A parallelization of the bi-conjugate gradient solver for the pressure equation of the CUPID (component unstructured program for interfacial dynamics) code, which was developed for analyzing the components of a pressurized water-cooled reactor, was studied in a symmetric multi-processing system. The parallel performance was investigated for three typical parallel programming models (MPI, OpenMP, Hybrid) by solving incompressible backward-facing step flow at various grid resolutions. It was confirmed that parallel performance was low when problem size was small or the memory requirement for each thread was considerably higher than the cache memory. Furthermore, it was shown that MPI was better than OpenMP regardless of the problem size, and Hybrid was the best when the number of threads was relatively small.

• Journal of Korean Society of Water and Wastewater
• /
• v.32 no.1
• /
• pp.55-65
• /
• 2018

It is necessary to develop a mobile water production system in order to provide stable water supply in case of disasters such as floods or earthquakes. In this study, we developed a modular mobile water production system capable of producing water for various uses such as domestic water and drinking water while improving applicability in various raw water sources. The water production system consists of three stages of filtration (sand filtration - activated carbon filtration - pressure filtration) to produce domestic water and an additional reverse osmosis process to produce drinking water. In laboratory and field experiments, the domestic water production system showed excellent treatment efficiency for particulate matter, but showed limitations in the treatment of dissolved substances such as dissolved organic matter. In addition, ultraviolet irradiation was considered as additional disinfection step, because it does not form precipitates of manganese oxides after disinfection. Reverse osmosis process was added to increase the removal efficiency of dissolved substances and the treated water satisfied drinking water quality standards. Fluorescence analysis of dissolved organic matter showed that the fulvic acid-like substances in raw water was successfully removed in the reverse osmosis process. The mobile water production system developed in this study is expected to be used not only in water supply in case of disaster, but also widely used in islands and rural area.

• Journal of Radiation Protection and Research
• /
• v.9 no.2
• /
• pp.97-102
• /
• 1984

Criticality analyses of the KSC-1(Korean Shipping Cask-1) spent fuel shipping cask have been performed with the help of KENO-IV Monte Carlo computer code and 19-group CSLIB 19 cross section set which was generated from AMPX modular system. The analyses followed a benchmark calculation which has been made regard to the B & W CX-10 criticality facility in order to validate the Monte Carlo code cross section set described above. The KSC-1 shipping cask seems to be safe in the criticality point of view for the transport of one PWR spent fuel assembly under the normal conditions as well as the hypothetical accident conditions.