• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.363-367
• /
• 2009

For the liquid rocket propulsion system using liquid oxygen as oxidizer, helium for pressurizing LOX is usually stored in the LOX tank with cryogenic temperature. For that kind of pressurizing system, cryogenic helium is discharged from the immerged pressurant cylinder and passes through the heat exchanger downstream of gas generator. During the process, helium pressurant is heated from cryogenic temperature to high one and supplied to the ullage of propellant tank. To develop the pressurizing system, a cryogenic heating apparatus is needed to simulate the heat exchanger. In this paper, the cryogenic heating apparatus for development of the pressurization system is presented along with its heating test results with cryogenic helium.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.63-68
• /
• 2011

For the liquid rocket propulsion system using liquid oxygen as oxidizer, helium for pressurizing LOX is usually stored in the LOX tank with cryogenic temperature. For that kind of pressurizing system, cryogenic helium is discharged from the immerged pressurant cylinder and passes through the heat exchanger downstream of gas generator. During the process, helium pressurant is heated from cryogenic temperature to high one and supplied to the ullage of propellant tank. To develop the pressurizing system, a cryogenic heating apparatus is needed to simulate the heat exchanger. In this paper, the cryogenic heating apparatus for development of the pressurization system is presented along with its heating test results with cryogenic helium.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.333-335
• /
• 2004

현재 저항 점 용접 공정에서 기존의 공기 가압 장치에서 서보모터를 이용한 서보 가압 장치로 변화가 진행되고 있다. 특히 마이크로 접합부의 경우 그 대상부가 미소ㆍ미세하기 때문에 접합부의 두께, 변형량, 접합후 전기 저항의 크기 둥이 크게 문제가 될 수 있다. (중략)

• Composites Research
• /
• v.31 no.1
• /
• pp.1-7
• /
• 2018

In the case of a conventional composite patch repair using a heat blanket, the adhesive is pressurized using only a vacuum bag. In this study, however, a pressurization system has been developed to apply additional air pressure on the vacuum bag. In order to verify the performance of the developed system, the composite laminates were repaired with scarf patches and then tested under tensile load to be compared with the strength of the defect-free laminate. Tensile tests were also conducted on specimens with the same configuration but bonded in an autoclave. As a result of the test, the tensile strengths of the specimens repaired using the heat blanket with vacuum only without external pressure, the specimens repaired with additional pressure by the developed system, and the specimens repaired with the same external pressure in an autoclave, showed the strength recovery ratios of 74.9, 81.0, and 78.2%, respectively. The results of the tensile test after moisture saturation and the dried fatigue test also showed that the strength recovery ratios of the specimens repaired under the external pressure of 1 atm using the developed system are slightly higher than that of specimens bonded in autoclave.

• Composites Research
• /
• v.27 no.6
• /
• pp.254-259
• /
• 2014

In this study, a device and pressure press process that is able to substitute autoclave process is developed. This process complements disadvantages of autoclave process which are long process-time and high production cost. The developed device provides air pressure as well as the vacuum which are greatest feature of autoclave process. The device is sealed using hydraulic pressure to keep the air pressure inside the mold. The transfer of the heat is designed to be direct. The heating and pressure charging time are decreased by reducing the interior space. Tooling cost is reduced dramatically compared to autoclave process. Spring-back phenomenon is measured and compared. The temperatures of several parts of the mold during molding are measured. The fiber volume fraction of the parts molded by autoclave process and by the developed process are compared.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.48-48
• /
• 2010

소형 공조장치용 냉매 압축기 부품인 기계식 제어 밸브는 에어컨 컴프레서의 핵심부품이고 년간 수백만 개가 국내에 수입된다. 이를 국산화 하기 위하여 진공로 속에서의 브레이징 공정이 수반되는 외국제품의 제조공정을 탈피하여 진공 속에서 DC 프로젝션 용접을 수행하는 기법을 개발하였다. 실린더 형상의 캡과 케이스를 맞대고 그 사이에 박판을 삽입한 상태에서 butt welding 방식으로 진행되는 본 공정에서는, 생산성이 높고 서보가압 장치를 사용하여 soft touch 를 구현하므로 프로젝션이 손상되지 않은 상태에서 통전이 시작되고 2 단 가압 및 프로파일 가압이 가능하므로 링(ring)형상의 너깃이 축대칭으로 안정적으로 형성되기 때문에 실린더 내부의 밀봉성능이 우수함을 확인하였다. 진공로 속에서 본 가압장치를 설치하여 간편한 방법으로 실린더 내부의 진공상태를 유지할 수 있기 때문에 진공로 속에서의 브레이징 공정이 적용되는 외국제품보다 생산성이 월등함을 알 수 있다. 본 연구에서 개발된 링 프로젝션(ring projection) 용접기법은 초소형 및 소형 실린더 형상의 부품 내부를 진공으로 유지해야 하는 산업현장에서 당장 적용될 수 있는 혁신적인 용접공정이라 판단된다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1027-1028
• /
• 2013

• 방재와보험
• /
• s.65
• /
• pp.24-31
• /
• 1995

• Nuclear industry
• /
• v.5 no.9 s.31
• /
• pp.29-34
• /
• 1985

원자력발전플랜트의 점검$\cdot$검사$\cdot$보수$\cdot$보수 등 메인터넌스 작업분야에서는 기기의 신뢰성 향상, 정기검사기간의 단축, 작업종사자의 피폭선량저감 등을 위하여 원격자동장치(원자력용 로보트)의 도입이 도모되어 왔다. 다음은 가압경수로형 원자력발전소(PWR)를 위한 원자력용 로보트의 개발$\cdot$적용상황에 관한 개요 소개이다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.3
• /
• pp.78-83
• /
• 2014

A special part such as a flow passage opening device is required to prevent the disconnection of fuel transfer in a pressurized fuel tank. To meet this requirement, the device utilizing an acceleration follow-up technique was invented. RecurDyn, a dynamic analysis tool, is introduced in this article to predict the device's performance and to determine parameters affecting it. In the analysis, it is shown that balancing weights can open the passage in accordance with fuel position.