• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.218-221
• /
• 2004

Dry sliding wear behavior of electro-pressure sintered Co, $Co-20\;wt.\%$ CuSn and $Co-20\;wt.\%$ WC composites were investigated. Wear tests of the materials were carried out using a pin-on-disk wear tester at various loads of 10N-100N under a constant sliding speed condition of 0.38m/s against glass ($83\%\;SiO_2$) beads. Sliding distances were varied with a range of $100m{\sim}600m$. A scanning electron microscopy was used to examine morphologies of worn surfaces, cross-sections, and wear debris. The $Co-20\;wt.\%$ WC composite had the highest and the $Co-20\;wt.\%$ CuSn composite showed the lowest wear resistance among the tested materials. All specimens exhibited low friction coefficients ranging from 0.12 to 0.4 at the applied load of 100N.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.183-183
• /
• 2011

리튬 이온 배터리의 cathode 및 electrolyte 재료로 사용되는 LiCoO2을 sputtering이나 pulsed laser deposition을 이용하여 박막으로 증착하기 위해서는 target이 필요하다. Target은 원료 분말을 가압 성형한 후 고온에서 소결하여 제조된다. LiCoO2 target 제조과정에서 고밀도를 얻기 힘들고 Li 성분의 증발이 일어난다. 또한 Li2O 분말은 흡습성이 매우 크다. 본 연구에서는 시간과 온도를 조절하여 최적화된 소결 과정을 통해 target의 밀도가 이론밀도와 근사한 값을 갖도록 하고, LiCoO2 또는 Co3O4 분말에 각각 흡습성이 낮은 Li2CO3 분말을 첨가하여 Li 성분을 조절하였다. Li과 Co의 조성비가 1:1-2:1인 고밀도의 LiCoO2 target을 제조하여 박막 증착 후 Li과 Co의 조성비가 1:1이 되도록 하였다.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.645-650
• /
• 2000

Effects of the chemical composition and sintering atmosphere on the formation of reaction phases and physical properties of reactive hot-pressed TiB2-AlN-BN composites were investigated. At N2 atmosphere, TiN was formed by the reaction between Ti and N2, which inhibited the densification and results in inferior mechanical-and electrical properties of the composites. However, at Ar atmosphere, enhanced densification and physical properties of composites were obtained due to that the TiN formation reaction was excluded. Densification of the composites was also hindered by BN, therefore, inferior mechanical-and electrical properties of composites were obtained with amount of BN in the starting materials. At Ar atmosphere, TiB2-AlN-BN composites having 318 MPa of flexural strength, 3.5 MPa.m1/2 of fracture toughness and 276$\mu$Ω.cm of electrical resistivity were fabricated from mole ratio 1:2:1.6 of Ti-Al-BN mixtures.

• Journal of the Korean Ceramic Society
• /
• v.29 no.6
• /
• pp.489-495
• /
• 1992

The continuous compaction response of zirconia powders prepared by different processing treatments was investigated. Though the yield point could be or not below 1 MPa, the change of slope was always observed at high pressure range around 60 MPa. Powder compaction was mainly governed by second compaction stage and compaction rate was decreased with increasing forming pressure. Rotary vacuum dried powder favored a high compaction density, whereas freeze dried and calcined powders favored an increase in the pressing efficiency. In order to extract more reliable information about powder compaction, it was necessary to use not only compaction response diagram but also compaction rate diagram.

• Journal of the Korean Ceramic Society
• /
• v.24 no.6
• /
• pp.602-604
• /
• 1987

The high TcY1Ba2Cu3Ox superconductor has recently gained widespread interest in the scientific community. The principal problems at the present time are how to densify this material and how to raise the critical current density. To date the majority of samples have had densities of 90%(of theoretical) or less. In this study we report that we obtained density of 96% by Hot-Pressing method.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.338-344
• /
• 2019

B₄C-SiC composites were fabricated using hot press sintering method without sintering additives at 1,900~2,000℃ under a pressure of 40 MPa. The crystal phase, relative density, microstructure, and mechanical properties of B₄C-SiC composites were evaluated. When B₄C and SiC were uniformly dispersed in the composite, grain growth was inhibited, and a sintered body with a fine and uniform microstructure, with improved mechanical properties, was fabricated. The relative density of B₄C-SiC composites sintered under 2,000℃ of temperature and 40 MPa of pressure was over 99.8 %, and the bending strength and Vicker's hardness at 50 wt% of B₄C were 645 MPa and 30.6 GPa, respectively.

• Korean Journal of Materials Research
• /
• v.30 no.6
• /
• pp.301-307
• /
• 2020

In this study, factors considered to be causes of promotion of densification of sintered pellets identified during phase change are reviewed. As a result, conclusions shown below are obtained for each factor. In order for MA powder to soften, a temperature of 1,000 K or higher is required. In order to confirm the temporary increase in density throughout the sintered pellet, the temperature rise due to heat during phase change was found not to have a significant effect. While examining the thermal expansion using the compressed powder, which stopped densification at a temperature below the MA powder itself, and the phase change temperature, no shrinkage phenomenon contributing to the promotion of densification is observed. The two types of powder made of Ti-silicide through heat treatment are densified only in the high temperature region of 1,000 K or more; it can be estimated that this is the effect of fine grain superplasticity. In the densification of the amorphous powder, the dependence of sintering pressure and the rate of temperature increase are shown. It is thought that the specific densification behavior identified during the phase change of the Ti-37.5 mol.%Si composition MA powder reviewed in this study is the result of the acceleration of the powder deformation by the phase change from non-equilibrium phase to equilibrium phase.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1102-1107
• /
• 1999

FeAl matrix composite was fabricated successfully by hot-pressing. The mechanical properties of FeAl alloys have been widely studies, but their behaviors of surface hardening effect by plasma nitriding has not yet been studied. This study was to analysis the relationship between microstructure of the sintered composite by hot-pressing and surface hardening at plasma nitriding treatment. Surface hardening of FeAl base alloys was improved by plasma nitriding with increasing plasma treatment time. Excellent surface hardness in the FeAl alloys could be obtained by plasma nitriding($\textrm{H}_{\textrm{v}}$ 100gf, diffusion layer: 1100~1450kg/$\textrm{mm}^2$, matrix : 330~360kg/$\textrm{mm}^2$). Diffusion layer size increased with increasing plasma nitriding times and decreased with increasing Sic, content.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.4
• /
• pp.1-5
• /
• 2000

Properties of AC applied hot pressed ($Pb_{1-x}Sn_{x}$) Te thermoelectrics were investigated. Mechanical alloying process used to produce alloyed powder to reduce the inhomogeneity and to avoid vaporization of constituents. It showed an increase in the mechanical alloying time with increasing of Sn contents in ($Pb_{1-x}Sn_{x}$)Te. ($Pb_{1-x}Sn_{x}$)Te were sintered at 873 to 923K for 1-4 minutes, under 150 kgf/$\textrm{cm}^2$ by AC applied hot pressng method. The short sintering time of AC applied hot pressing process could reduce the vaporization of Te. The density of ($Pb_{1-x}Sn_{x}$) Te was more dependent on the sintering temperature than the sintering time. The p-n transition was observed at x=0.1 but only p type conduction behavior was observed at more than 20 mol% of Sn compositions. The maximum value of Seebeck coefficient is 250 $\mu$V/K for x=0.2 at 500K. As the amount of Sn increases, the peak value of Seebeck coefficient drops and shifts to higher temperature and the peak value of electrical conductivity decreased with increasing temperature.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.3
• /
• pp.115-119
• /
• 2001

Hydroxyapatite-yttria stabilized zirconia bioceramics containing fine zirconia particles were prepared as 3-layered functionally graded materials (FGMs) using a spark plasma sintering (SPS) and hot pressing (HP) apparatuses. The pretreatment of the raw hydroxyapatite promoted the sinterability of hydroxyapatite. The maximum density of pretreated FGM composites could be obtained at lower temperature than that for he untreated FGM samples. No decomposition from hydroxyapatite to three calcium phosphate (TCP) was observed in FGMs of HAp-$ZrO_2$ sintered below $1200^{\circ}C$ for 8 min under 10 MPa by SPS. However, the transformation of the tetragonal zirconia to the cubic modification had occurred in FGMs at this temperature. The presence of zirconia i.e. stress induced transformation of zirconia may be expected to enhance the mechanical properties of HAp-$ZrO_2$ FGM. The SPS is concluded as a better method to fabricated the FGM with dense and high strength compared with HP process.