• Journal of the Korean Electrochemical Society
• /
• v.3 no.1
• /
• pp.11-14
• /
• 2000

Transparent conducting ITO thin films have been studied and developed for the solar cell substrate or LCD substrate. ITO thin film has been mostly fabricated by high cost sputtering method. In this research, sol-gel method is applied to fabricate ITO thin film at lower cost. The research is focused on the establishment of process condition and development of precursor. Organic sol was made of indium tri-isopropoxide dissolved in ethylene glycol monoethyl ether. The hydrolysis was controled by addition of acetyl acetone. Tin(IV) chloride was added as dopant. Inorganic sol was made of indium acetate dissolve din normal propanol. Spin coating technique was applied to coat ITO on borosilicate glass. The resistivity of ITO thin film was approximately $0.01\Omega{\cdot}cm$ and the transmittance is higher than $90\%$ in a visible range.

• Journal of the Korean Ceramic Society
• /
• v.24 no.5
• /
• pp.447-452
• /
• 1987

${\alpha}$-Al2O3 powder was produced at 1000$^{\circ}C$ by the boehmite sol-gel process with seeding 2 wt% ${\alpha}$-Al2O3. The processes and mechanisms of fornation of ${\alpha}$-Al2O3 was investigated using DTA/TG, XRD, TR spectroscopy and thermodynamic analysis. The specific surface area of the obtained ${\alpha}$-Al2O3 was 16.3㎡/g.

• Journal of Sensor Science and Technology
• /
• v.19 no.3
• /
• pp.202-208
• /
• 2010

This study examined the dependency of crystalline orientation and electric properties of sol-gel PZT film on hydrolysis, a $PbTiO_3$ seed layer and a concentration of sol-gel solution. The PZT thin films were prepared by using 2-Methoxyethanol-based sol-gel method and spin-coating on Pt/Ti/$SiO_2$/Si substrates. The 1-${\mu}m$-thick PZT films were coated and then fired in a furnace by direct insert method. The highly (111) oriented PZT film of pure perovskite structure could be obtained. We could control the degree of orientation by various parameters such as hydrolysis, a $PbTiO_3$ seed layer and a concentration of sol-gel solution. The highest measured remanent polarization, dielectric constant and piezoelectric coefficient are $24.16\;{\mu}C/cm^2$, 2808, and 159 pC/N, respectively.

• Solar Energy
• /
• v.12 no.2
• /
• pp.18-27
• /
• 1992

Multilayer coatings of $WO_3$ were deposited by the sol-gel technique on microscope slide glass and ITO coated glass. These films were characterized optically, chemically, and structurally by XRD, spectro-photometry, DTA/TGA, SEM/EDAX and RBS. Uniform $WO_3$ sol-gel films were dip coated on slide glass at dipping speed of 5mm/s. This sample indicated a low near IR transmittance in optical properties as a result of coloration using a dilute HCI electrolyte as the $H^+$ion sources. Differential thermal analysis results have allowed the accurate determination of the formation temperature of the $WO_3$ crystalline phase from the gel data in the range of $380^{\circ}C{\sim}500^{\circ}C$, consistent with crystallization temperature of sol-gel film. RBS spectrometry was performed on the uncolored $WO_3$ sol-gel film, yielding a chemical composition of $WO_3$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.11a
• /
• pp.34-34
• /
• 1999

• Journal of the Korean Ceramic Society
• /
• v.29 no.3
• /
• pp.211-215
• /
• 1992

Crack free PbTiO3 ceramics were produced by sol-gel processing using alkoxide, which has not been reported to be successful. The PbTiO3 gels were prepared from Ti alkoxide and lead acetate without any dopants. They were calcined at $600^{\circ}C$ and miled to produce fine PbTiO3 powder. It was pressed into discs and they were sintered at 110$0^{\circ}C$ for a few hours. The sintered ceramics were relativley hard and dense as having about 96% of theoretical density of PbTiO3. Fabrication of pure PbTiO3 ceramics by sol-gel processing is possibly due to their small grain size and uniform distribution of residual stress created during cubic-tetragonal transition over large number of small grains in fine grain PbTiO3 ceramics.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.165-170
• /
• 2005

Sol-gel methods offer many advantages over conventional slip-casting, including the ability to produce ceramic membranes. They are purer, more homogeneous, more reactive and contain a wider variety of compositions. We produced ormosil sol using sol-gel process under various molecular weight of polymer species[polyethylene glycol(PEG)] in total system [Tetraethyl ortho silicate(TEOS)-polyethylene glycol(PEG)]. The properties of as-prepared ormosil sol such as viscosity and gelation time are characterized. Also, the ceramic membrane was prepared by dip-coating with synthetic sol and its microstructure was observed by scanning electron microscopy. The permeability and rejection efficiency of membrane for oil/water emulsion were evaluated as cross­flow apparatus. The ormosil sol coated membrane was easily formed by steric effect of polymer and it improved flux efficiency because infiltration into porous support decreased. Its flux efficiency was elevated about $200\;l/m^2h$ compared with colloidal sol coated membrane at point of five minutes from starting test.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.3
• /
• pp.271-277
• /
• 2000

Transparent $TiO_2$ thin films were prepared by the sol-gel method from titanium alkoxide aqueous solution containing large quantities of water. To prepare the aqueous system sol, the chelate compound solution were prepared from each 1 mole of titanium(IV)iso-propoxide, acetylacetone and 8 moles of isopropyl-alcohol. And then the 50 moles aqueous solution with the 0.02~0.50 moles of HCI for sol stability and the 0.3 mole of polyethylene glycol for coating adhesion were precisely dropped on the chelate compound solution. $TiO_2$thin films were fabricated by dip coating, drying and heat treatment at $400^{\circ}C$ and their characteristics were investigated by XRD, SEM and UV-visible spectrometer, The neutral sol of composition with TTIP : AcAc : IPA : $H_2O$ : PEG : HCl = 1 : 1 : 8 : 50 : 0.3 : 0.15 (molar ratio) was maintained stable sol condition and without problem for coating more than 30 days. The anatase phase $TiO_2$thin film prepared from 30 times dipping, drying and heat treating showed the flat surface and the fine microstructure of fracture surface with about 2 $\mu\textrm{m}$ thickness. Transparency of these $TiO_2$thin film was 80 % in the visible region.

• Korean Journal of Materials Research
• /
• v.30 no.11
• /
• pp.609-614
• /
• 2020

3 mol% yttria-doped stabilized zirconia (3YSZ) is synthesized by a solvothermal process, and its characteristics are investigated using various methods. Also, the dispersibility of synthesized 3YSZ nanoparticles is observed with the species of surface modifier. The 3YSZ nano sol prepared with an optimum condition is employed in prism coating and its properties are evaluated. The synthesized 3YSZ nanoparticles show a globular shape with about 10 to 20 nm crystallite size. The mixed phases with the nano sol show a high specific surface of 178 ㎡/g. The prism sheet coated with the 3YSZ nano sol present an excellent refractive index, transmittance, and luminance; refractive index is 1.603, transmittance is 90.2 %, and luminance of coating film is improved by 5.9 % compared to that of the film without 3YSZ nano sol. It is verified that the surface modified 3YSZ is suitable as the prism sheet for optical displays.

• Journal of the Korean Mathematical Society
• /
• v.52 no.6
• /
• pp.1209-1251
• /
• 2015

The purpose of this paper is to classify all compact manifolds modeled on the 4-dimensional solvable Lie group $Sol_1^4$, and more generally, the crystallographic groups of $Sol_1^4$. The maximal compact subgroup of Isom($Sol_1^4$) is $D_4={\mathbb{Z}}_4{\rtimes}{\mathbb{Z}}_2$. We shall exhibit an infra-solvmanifold of $Sol_1^4$ whose holonomy is $D_4$. This implies that all possible holonomy groups do occur; the trivial group, ${\mathbb{Z}}_2$ (5 families), ${\mathbb{Z}}_4$, ${\mathbb{Z}}_2{\times}{\mathbb{Z}}_2$ (5 families), and ${\mathbb{Z}}_4{\rtimes}{\mathbb{Z}}_2$ (2 families).