• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.196-197
• /
• 2010

NAND형 charge trap flash (CTF) non-volatile memory (NVM) 소자가 30nm node 이하로 고집적화 되면서, 기존의 SONOS형 CTF NVM의 tunnel barrier로 쓰이는 SiO2는 direct tunneling과 stress induced leakage current (SILC)등의 효과로 인해 data retention의 감소 등 물리적인 한계에 이르렀다. 이에 따라 개선된 retention과 빠른 쓰기/지우기 속도를 만족시키기 위해서 tunnel barrier engineering (TBE)가 제안되었다. TBE NVM은 tunnel layer의 전위장벽을 엔지니어드함으로써 낮은 전압에서 전계의 민감도를 향상 시켜 동일한 두께의 단일 SiO2 터널베리어 보다 빠른 쓰기/지우기 속도를 확보할 수 있다. 또한 최근에 각광받는 high-k 물질을 TBE NVM에 적용시키는 연구가 활발히 진행 중이다. 본 연구에서는 Si3N4와 HfAlO (HfO2 : Al2O3 = 1:3)을 적층시켜 staggered의 새로운 구조의 tunnel barrier Capacitor를 제작하여 전기적 특성을 후속 열처리 온도와 방법에 따라 평가하였다. 실험은 n-type Si (100) wafer를 RCA 클리닝 실시한 후 Low pressure chemical vapor deposition (LPCVD)를 이용하여 Si3N4 3 nm 증착 후, Atomic layer deposition (ALD)를 이용하여 HfAlO를 3 nm 증착하였다. 게이트 전극은 e-beam evaporation을 이용하여 Al를 150 nm 증착하였다. 후속 열처리는 수소가 2% 함유된 질소 분위기에서 $300^{\circ}C$와 $450^{\circ}C$에서 Forming gas annealing (FGA) 실시하였고 질소 분위기에서 $600^{\circ}C{\sim}1000^{\circ}C$까지 Rapid thermal annealing (RTA)을 각각 실시하였다. 전기적 특성 분석은 후속 열처리 공정의 온도와 열처리 방법에 따라 Current-voltage와 Capacitance-voltage 특성을 조사하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.404-410
• /
• 1989

Friction and wear tests were conducted with several different ceramics sliding against ceramic and metal couples with and without lubricant in a two disk type sliding machine. The purpose was to know the tribological properties of ceramics. With very different physical and chemical properties of ceramics compared to metal, the tribological properties of ceramics should be defined in detail. Among them, the wear and friction with same or different couple is very important. Also the lubrication of ceramic is one of the major area to be studied. From this research, SiC, SI$_{3}$N$_{4}$ and ZrO$_{2}$ were slid against SiC, AISI 4340 and bronze under various sliding condition. It was found that the friction and wear of ceramics are strongly dependent on the sliding condition. For unlubricated sliding against SiC, ZrO$_{2}$ shows low wear and friction coefficient over wide lange of load, but with lubricated sliding, SiC shows better performance whatever lubricants were used. Also the effect of lubricant depended upon the material properties of sliding pairs. The general tribological properties of ceramics were not correlated with chattering and noise at low load but it could be reduced or avoided effectively by using lubricants. SiC and Si$_{3}$N$_{4}$ slid against SiC have transition from mild to severe wear at high load but ZrO$_{2}$-SiC and SiC-steel have not. Wear debris formed on the contact area of SiC couples was main cause of the initiation of transition. At high speed, only ZrO$_{2}$ sliding against SiC has transition of wear by low thermal conductivity.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.97.2-97.2
• /
• 2018

This study formed a hard TiAlSiWN coating layer using Ti, Al, Si and W raw powders that were mechanically alloyed and refined. The TiAlSi and TiAlSiW coating targets were fabricated using a single PCAS process in a short time with the optimal sintering conditions. The coating targets were deposited on the WC substrate by forming coating layers using TiAlSiN and TiAlSiWN nitride nano-composite structures with an AIP process. The properties of the nitride nano-composite coating layers were compared according to the addition of W. The microstructure of the nitride nano-composite coating layer was analyzed, focusing on the distribution of the crystalline phases, amorphous phases ($Si_3N_4$), and growth orientation of the columnar crystal depending on the addition of W. The mechanical properties of the coating layers were exhibited a hardness of approximately $3,000kg/mm^2$ and adhesion of about 117.77N in the TiAlSiN. In particular, the TiAlSiWN showed excellent properties with a hardness of more than $4,300kg/mm^2$ and an adhesion of about 181.47N.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.34-34
• /
• 2009

The electrical characteristics of tunnel barrier engineered charge trap flash (TBE-CTF) memory with $SiO_2/Si_3N_4/SiO_2/Si$ engineered tunnel barrier, $HfO_2$ charge trap layer and $Al_2O_3$ blocking oxide layer (MAHONOS) were investigated. The energy bad diagram was designed by using the quantum-mechanical tunnel model (QM) and then the CTF memory devices were fabricated. As a result, the best thickness combination of MAHONOS is confirmed. Moreover, not enhanced P/E speed (Program: about $10^6$ times) (Erase: about $10^4$ times) but also enhanced retention and endurance characteristics are represented.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.193-193
• /
• 2010

서로 다른 유전 물질을 이용하여 다층구조의 터널장벽을 이용하여 비휘발성 메모리 소자의 동작 특성 및 전하보존 특성을 향상시킬 수 있음이 보고되었다.[1-3] 본 연구에서는 $SiO_2/Si_3N_4/SiO_2$구조의 다층 구조의 터널 장벽을 이용하여 $WSi_2$ 나노 입자 비휘발성 메모리 소자를 제작하였다. P-형 Si 기판에 100 nm 두께의 Poly-Si 박막을 증착시켜 소스, 드레인 및 게이트 영역을 포토 리소그래피를 이용하여 형성하였다. $SiO_2/Si_3N_4/SiO_2$(ONO) 터널장벽은 CVD (chemical vapor deposition) 장치로 각각 2 nm, 2 nm 와 3 nm 두께로 형성하였으며, 그 위에 $WSi_2$ 박막을 3~4 nm 마그내트론 스퍼터링 방법으로 증착하였다. ONO 터널 장벽구조 위에 $WSi_2$나노입자를 형성시키기 위해, $N_2$분위기에서 급속열처리 방법을 이용하여 $900^{\circ}C$에서 1분간 열처리를 하였다. 마지막으로 20 nm 두께의 컨트롤 절연막을 초고진공 스퍼터를 이용하여 증착하고, Al 박막을 200 nm 두께로 증착하였다. 여기서. 제작된 메모리 소자의 게이트 길이와 선폭은 모두 $10\;{\mu}m$ 이다. 비휘발성 메모리 소자의 전기적 특성은 HP 4156A 반도체 파라미터 장비, Agilent 81104 A 80MHz 펄스/패턴 발생기를 이용하였다. 또한 전하 저장 터널링 메커니즘과, 전하누설의 원인을 분석하고 소자의 열적 안정성을 확인하기 위하여 $25^{\circ}C$ 에서 $125^{\circ}C$ 로 온도를 변화시켜 외부로 방출되는 전하의 활성화 에너지를 확인하여 누설근원을 확인하였다.

• Journal of Sensor Science and Technology
• /
• v.18 no.4
• /
• pp.311-315
• /
• 2009

This paper describes the characteristics of a poly 3C-SiC micro heater which was fabricated on AlN(0.1 $\mu$m)/3C-SiC(1.0 $\mu$m) suspended membranes by surface micro-machining technology. The 3C-SiC and AlN thin films which have wide energy band gap and very low lattice mismatch were used sensors for high temperature and voltage environments. The 3C-SiC thin film was used as micro heaters and temperature sensor materials simultaneously. The implemented 3CSiC RTD(resistance of temperature detector) and the power consumption of micro heaters were measured and calculated. The TCR(thermal coefficient of the resistance) of 3C-SiC RTD is about -5200 ppm/$^{\circ}C$ within a temperature range from 25 $^{\circ}C$ to 50 $^{\circ}C$ and -1040 ppm/$^{\circ}C$ at 500 $^{\circ}C$. The micro heater generates the heat about 500 $^{\circ}C$ at 10.3 mW. Moreover, durability of 3C-SiC micro heaters in high voltages is better than Pt micro heaters. A thermal distribution measured and simulated by IR thermovision and COMSOL is uniform on the membrane surface.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.29-35
• /
• 2004

We have deposited the W-N diffusion barrier on Si substrate with $NH_3$ pulse plasma enhanced atomic layer deposition (PPALD) method by using $WF_6$ and $NH_3$ gases. The $WF_6$ gas reacts with Si that the surface corrosion occurs severely, but the $NH_3$ gas incorporated with pulse plasma and $WF_6$ gas are easily deposited W-N thin film without Si surface corrosion. Because the $NH_3$ with pulse plasma can be active species dissociated and chemisorbed on Si. Thus the Si surface are covered and saturated with nitrogen, which are able to deposit the W-N thin film. We also examine the deposition mechanism and the effect of $NH_3$ pulse plasma treatment.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.6
• /
• pp.245-249
• /
• 2006

In this study, ternary Ti-Mo-N and new quaternary Ti-Mo-Si-N coatings were synthesized on steel substrates(AISI D2) and Si wafers by a hybrid coating system of arc ion plating (AIP) using Ti target and d.c. magnetron sputtering technique using Mo and Si targets in $N_2/Ar$ gaseous mixture. Ternary Ti-Mo-N coatings were substitutional solid-solution of (Ti, Mo)N and showed maximum hardness of approximately 30 GPa at the Mo content of ${\sim}10$. %. The Ti-Mo-Si-N coating with the Si content of 8.8 at. % was a composite consisting of fine (Ti, Mo)N crystallites and amorphous $Si_3N_4$ phase. The hardness of the Ti-Mo-Si(8.8 at. %)-N coatings exhibited largely increased hardness value of ${\sim}48$ GPa due to the microstructural evolution to the fine composite microstructure and the refinement of (Ti, Mo)N crystallites. The average friction coefficient of the Ti-Mo-Si-N coatings largely decreased with increase of Si content. The microstructures of Ti-Mo-Si-N coatings were investigated with instrumental analyses of XRD, XPS, and HRTEM in this work.

• Journal of the Korean Magnetics Society
• /
• v.13 no.1
• /
• pp.6-14
• /
• 2003

The purpose of this study is to investigate the effect of chemical reaction with a bonding glass on physical and magnetic properties of Fe-Hf-N/SiO$_2$ and Fe-Hf-N/Cr/SiO$_2$ thin films. When the Fe-Hf-N/SiO$_2$ films were reacted with the bonding glass, the soft magnetic properties of them were extremely degraded. At $600^{\circ}C$, the saturation magnetization of the reacted film decreased to 1 kG, and its coercivity increased to 27 Oe, and its effective permeability decreased to 70. It was found that the degradation of soft magnetic properties of the Fe-Hf-N/SiO$_2$ films reacted with the bonding glass were attributed to the oxidation of the Fe-Hf-N layers to HfO$_2$ and Fe$_3$O$_4$. The soft magnetic properties of the Fe-Hf-N/Cr/SiO$_2$ films reacted with the bonding glass were degraded less than those of Fe-Hf-N/SiO$_2$ films. At $600^{\circ}C$, the saturation magnetization of the reacted film decreased to 13.5 kG, and its coercivity increased to 4 Oe, and its effective permeability decreased to 700. It was found that the Cr layer suppressed the oxidation of the Fe-Hf-N layers during the chemical reaction between the Fe-Hf-N layer and bonding glass.

• Journal of the Korean Ceramic Society
• /
• v.25 no.2
• /
• pp.143-153
• /
• 1988

In order to synthesize the partially stabilized $\alpha$-Sialon, A1N and Y2O3 were added to synthesized $\alpha$-Si3N4. The phase composition, mechanical properties, micro structure, etc, of the synthesized $\alpha$-Sialon were investigated. Partially stabilized $\alpha$-Sialon ceramics could be synthesized from the composition which was a little deviated from x=0.4, x=0.6 composition along the Si3N4.0.1Y2O3:0.9AlN tie line at 1750-180$0^{\circ}C$ for 2 hrs in N2 atmosphere. It is assumed that A1N is more closely related than Y2O3 to the formation of $\alpha$-Sialon, and that A1N is more easily dissolved into $\alpha$-structure than into $\beta$-structure. In Ya2O3-rich phase mechanical properties were observed to be poor because of formation of mellilite, grain growth, and thermal decomposition of $\alpha$-Sialon. The maximum values of M.O.R, KIC and hardness are 723 MPa, 4.5MN/㎥/2 and 19.3 GPa, respectively, and they were observed for the $\alpha$-Sialon ceramics sintered at 178$0^{\circ}C$.