• Journal of Korea Foundry Society
• /
• v.2 no.3
• /
• pp.16-24
• /
• 1982

For the purpose of development of domestic carburizer, when the basicity of ash in carburizer was changed from $Na_2O/Al_2O_3+SiO_2$ ; 0.06 to $Na_2O/Al_2O_3+SiO_2$ ; 0,196wt%, using $Na_2O$ as flux for domestic graphite resource (Bong Myung armorphous graphite), carburizing efficiency was improved as basicity increased, optimum basicity value was $Na_2O/Al_2O_3+SiO_2$ ; 0.151. This means that $Na_2O$ contributed to lower viscosity of slag and raise occurence probability of specific reaction surface between molten iron and carburizer. The experiment of effect of general characteristics offecting carburizing ability of this carburizer was performed, the result is that 10/30 mesh was optimum size of the carburizer and as carbon equivalent of molten iron was higher, carburizing ratio was lowered, but when si concentration was below 1.8% in general cast iron melting region, recovery showed 75-85%. As agitation rate of molten iron and temperature interval were higher, Carburizing ratio was increased and showed max, 94%. Desulfurizing phenomena of molten iron by $Na_2O$ in carburizer didn't appear.

• Journal of Conservation Science
• /
• v.33 no.3
• /
• pp.215-223
• /
• 2017

The purpose of this study is to reveal the characteristics, correlations, and colorant materials of those using the chemical compositions of 30 glasses excavated from the Sarari hall of the Mireuksaji stone pagoda, and to determine the correlations between them and other glass excavated from the Wanggungri site. The results of the chemical analysis of the 11 glass beads show that they are a soda glass group with high contents of $SiO_2$ and $Na_2O$; these can be further subdivided into soda-alumina groups ($Na_2O-Al_2O_3-CaO-Si_2O$). The characteristics of the stabilizer are classified as being of the high alumina glass group (LCHA), except for two glasses. It was concluded that colorant materials affected the coloring for glass beads by various components including Ti, Mn, Fe, Cu and Pb. In addition, we examined six lead glasses which are glass plate and unknown fragments that are of a common lead glass system ($PbO-SiO_2$) with respect to the average contents of PbO (70wt.%) and $SiO_2$ (30wt.%). As a result of comparing these relics with those of the glass beads excavated by Wanggungri, there is a similarity in that they belong to the soda glass group. However, the contents of $Na_2O$ are relatively higher than that of the glass beads in the Mireuksaji pagoda, and most of relics include glasses with a low content of $K_2O$ and CaO. In addition, the PbO and $SiO_2$ contents are slightly different in the lead glass. It seems that the glass relics made at two different sites may have used different raw materials or techniques.

• Journal of the Korean Chemical Society
• /
• v.52 no.1
• /
• pp.47-51
• /
• 2008

A simple synthetic strategy is described for one-pot synthesis of 5,7-diaryl-4,4-dimethyl-4,5,6,7-tetrahydropyridino[3,4-d]-1,2,3-selenadiazoles (11-15) in the presence of NaHSO4.SiO2 as a heterogeneous catalyst in dry media under microwave irradiation.Key words: One-pot synthesis, 3,3-Dimethyl-2,6-diarylpiperidin-4-one; 1,2,3-Selenadiazoles; Selenium dioxide; NaHSO4.SiO2 Heterogeneous catalyst.

• Journal of the Korean Ceramic Society
• /
• v.17 no.1
• /
• pp.20-26
• /
• 1980

The crystallization behaviors of slag-based glass in $CaO-MgO-Al_2O_3-SiO_2(-Na_2O)$ system have been studied. The mother glass containing 16.50 CaO, 7.50MgO, 19.70Al2O3, 50.80SiO3 and 2.09wt% $Na_2O$ was prepared by using Korean domestic raw materials such as granulated slag, serpentine, sea sand and etc. The glass-ceramics composed of major crystalline phase diopside was produced by the heat treatment in a temperature range from 850$^{\circ}$ to 9$25^{\circ}C$ for 0-6hr. The composition and morphology of diopside phase formed in the system were examined by X-ray diffraction analysis and electron microscopy. The kinetic measurements such as J.M. A plot and Arrhenius plot indicated that the process of nucleation of the initially formed diopside phase could be described from the view point of instantaneous nucleation. It was also demonstrated that the linear crystal growth of diopside phase was proceeded by short range diffusion of $Mg^{2+}$ and $Ca^{2+}$ ion. The microstructures of the resulting glass-ceramics were consisted of leafroidal shaped crystalline aggregations.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2001.11a
• /
• pp.189-189
• /
• 2001

• Journal of the Korean Ceramic Society
• /
• v.30 no.10
• /
• pp.871-879
• /
• 1993

Effects of K2SO4 and Na2SO4 on C3S formation and its microstructure were investigated. C3S formation was not influenced by addition up to 6.0wt% of K2SO4 as SO3 base, however it was prevented by only 1.0wt% of Na2SO4 addition. C3S prevention by added Na2SO4 was the reason why C2S stabilized by Na+ and SO42- could not react to C3S. Added K2SO4 appeared as K2SO4, however added Na2SO4 appeared as the form of Na2xCa3-xAl2O6, (Na0.8Ca0.1)SO4 and Na2SO4 in interstitial phase.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.4
• /
• pp.190-195
• /
• 2009

Na-tetrasilicic fluorine mica powders were synthesized by skull melting method. The staring materials having chemical composition of $Mg_3(OH)_2Si_4O_{10}:Na_2SiF_6:SiO_2=8.3:24.8:66.9$ mol% were charged into a cold crucible of 13 cm in diameter and 14cm in height and heated by R.F. generator at working frequency of 2.84 MHz. The materials were maintained for 1hr as a molten state and cooled down in the container. In this study, the specific electric resistance of mica was estimated and the columnar and plate shaped mica were synthesized.

• International Journal of Highway Engineering
• /
• v.15 no.3
• /
• pp.1-8
• /
• 2013

PURPOSES : This study is to evaluate the feasibility of using the alkali activated cement concrete for application of partial-depth repair in pavement. METHODS : This study analyzes the compressive strength of alkali activated cement mortar based on the changes in the amount/type/composition of binder(portland cement, fly ash, slag) and activator(NaOH, $Na_2SiO_3$, $Na_2CO_3$, $Na_2SO_4$). The mixture design is divided in case I of adding one kind-activator and case II of adding two kind-activators. RESULTS : The results of case I show that $Na_2SO_4$ based mixture has superior the long-term strength when compared to other mixtures, and that $Na_2CO_3$ based mixture has superior the early strength when compared to other mixtures. But the mixtures of case I is difficult to apply in the material for early-opening-to-traffic, because the strength of all mixtures isn't meet the criterion of traffic-opening. The results of case II show that NaOH-$Na_2SiO_3$ based mixtures has superior the early/long-term strength when compared to NaOH-$Na_2SiO_3$ based mixtures. In particular, the NaOH-$Na_2SiO_3$ based some mixtures turned out to pass the reference strength(1-day) of 21MPa as required for traffic-opening. CONCLUSIONS : With these results, it could be concluded that NaOH-$Na_2SiO_3$ based mixtures can be used as the material of pavement repair.

• Journal of the Korean Ceramic Society
• /
• v.43 no.1 s.284
• /
• pp.1-3
• /
• 2006

Well-shaped NaA zeolite cubic crystals of a large size of $5-7{\mu}m$ were synthesized by a hydrothermal method in a mother solution having a $3.55Na_2O:Al_2O_3:1.6SiO_2:593\~2000H_2O$ composition. Thermal treatment of NaA zeolite crystals resulted in the formation of a crystalline phase of $NaAlSiO_4-Camegeite$ between 800 and $900^{\circ}C$. Even at $1000^{\circ}C,\;NaAlSiO_4$ phase was found as a major product. Environmental Scanning Electron Microscopy (ESEM), High Resolution Transmission Electron Microscopy (HRTEM), X-Ray powder Diffraction (XRD), Fourier Transform Infrared (FT-IR) spectroscopy, and DTA/TGA and BET analyses were used to characterize the initial materials and the obtained products after various heat treatments.

• Clean Technology
• /
• v.26 no.4
• /
• pp.263-269
• /
• 2020

Zeolite was synthesized hydrothermally using the water-treatment sludge, and the effects of various synthesis parameters like reaction temperature, reaction time, and Na2O/SiO2 molar ratio on the crystallization of zeolite were investigated. Crystal structure, physical property, and thermal stability of zeolite crystals were characterized by X-ray powder diffraction, FTIR spectroscopy, BET nitrogen adsorption, and TGA measurements. The removal efficiencies of nitrogen in ammonia, heavy metal ions, and TOC were calculated to evaluate zeolite's adsorption capacity. The primary chemical composition of water-treatment sludge was 28.79% Al2O3 and 27.06% SiO2. The zeolites were synthesized by merely employing the water-treatment sludge as silica and alumina sources without additional chemicals. Zeolite crystals synthesized through the water-treatment sludge were confirmed as an A-type zeolite structure. Zeolite A had the highest crystallinity obtained from a gel with the molar composition 2.1Na2O-Al2O3-1.6SiO2-65H2O after 5 h at a temperature of 90 ℃. The specific surface area of zeolite obtained was 55 ㎡ g-1, which was higher than commercial zeolite A. The removal efficiency of nitrogen in ammonia was 68% after 3 h of reaction time, while the removal efficiencies of Pb2+ and Cd2+ ions were 99.1% and 99.3%, respectively. These results indicate active ion exchange between Pb2+ or Cd2+ ion and Na+ ion in the zeolite framework. The adsorption experiments on the different zeolite addition conditions were performed for 3 h with 300 ppm humic acid. Based on the results, TOC's highest efficiency was 83% when 5 g of zeolite was added.