• Journal of the Korean Ceramic Society
• /
• v.25 no.3
• /
• pp.201-206
• /
• 1988

To investigate the effects of Mo addition on the microstructures and mechanical properties of Al_2O_3$ ceramics, two kinds of Mo particles with average sizes of 2-${\mu}{\textrm}{m}$ and 6-${\mu}{\textrm}{m}$ were used as additives. It was shown that Mo particles inhibited the grain growth of Al_2O_3$, and the smaller Mo particles were more effective. In case of 2-${\mu}{\textrm}{m}$ Mo dispersion, the bending strength and the fracture toughness were increased. Dispersion of 6-${\mu}{\textrm}{m}$ MO did not increase the strength but improved the fracture toughness a little. The toughening mechanisms of Al_2O_3$-Mo composites are thought to be the crack deflection and microcracking mechanisms.

• Applied Chemistry for Engineering
• /
• v.10 no.2
• /
• pp.231-236
• /
• 1999

Several series of morphologically controlled $MoO_3$/$SiO_2$ catalysts were prepared, characterized, and tested for hydrodesulfurization (HDS) of dibenzothiophene (DBT) activity. Molybdenum surface loaded with 4.0 atoms $Mo/nm^2$ was prepared as sintered hexagonal and sintered orthorhombic, as well as a novel "well dispersed hexagonal" phase. Characterization by XRD, Raman, and $O_2$ chemisorption results reveals that the dispersion of $MoO_3$ over silica depends on the final $MoO_3$ phase in the order of; sintered hexagonal < sintered orthorhombic < dispersed hexagonal phase. Temperature programmed reduction (TPR) results show that both bulk and dispersed microcrystalline of $MoO_3$ reduce to $MoO_2$ at $650^{\circ}C$ and to Mo metal at $1000^{\circ}C$. HDS of DBT was performed in a differential reactor at 30 atm over the temperature range $350{\sim}500^{\circ}C$. Activity of $MoO_3$/$SiO_2$ toward HDS of DBT is proportional to dispersion.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.10
• /
• pp.1623-1632
• /
• 2006

NiO supported on zirconia modified with $MoO_3$ for acid catalysis was prepared by drying powdered $Ni(OH)_2-Zr(OH)_4$ with ammonium heptamolybdate aqueous solution, followed by calcining in air at high temperature. The characterization of prepared catalysts was performed using FTIR, Raman, XRD, and DSC. $MoO_3$ equal to or less than 15 wt% was dispersed on the surface of catalyst as two-dimensional polymolybdate or monomolybdate, while for $MoO_3$ above 15 wt%, crystalline orthorhombic phase of $MoO_3$ was formed, showing that the critical dispersion capacity of $MoO_3$ on the surface of catalyst is 0.18 g/g NiO-$ZrO_2$ on the basis of XRD analysis. Acidity and catalytic activities for acid catalysis increased with the amount of dispersed $MoO_3$. The high acid strength and acidity was responsible for the Mo=O bond nature of the complex formed by the interaction between $MoO_3$ and $ZrO_2$. The catalytic activity for acid catalysis was correlated with the acidity of the catalysts measured by the ammonia chemisorption method.

• Journal of Powder Materials
• /
• v.26 no.3
• /
• pp.208-213
• /
• 2019

In this study, lanthanum oxide ($La_2O_3$) dispersed molybdenum ($Mo-La_2O_3$) alloys are fabricated using lanthanum nitrate solution and nanosized Mo particles produced by hydrogen reduction of molybdenum oxide. The effect of $La_2O_3$ dispersion in a Mo matrix on the fracture toughness at room temperature is demonstrated through the formation behavior of $La_2O_3$ from the precursor and three-point bending test using a single-edge notched bend specimen. The relative density of the $Mo-0.3La_2O_3$ specimen sintered by pressureless sintering is approximately 99%, and $La_2O_3$ with a size of hundreds of nanometers is uniformly distributed in the Mo matrix. It is also confirmed that the fracture toughness is $19.46MPa{\cdot}m^{1/2}$, an improvement of approximately 40% over the fracture toughness of $13.50MPa{\cdot}m^{1/2}$ on a pure-Mo specimen without $La_2O_3$, and this difference in the fracture toughness occurs because of the changes in fracture mode of the Mo matrix caused by the dispersion of $La_2O_3$.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.12
• /
• pp.1239-1244
• /
• 2000

A study of K addition to the catalyst of CoMo/ ${\gamma}-Al_2O_3$ was studied. The catalyst with 10 at% of K to Mo atoms in 3C10M, the catalyst added 3 wt% CoO to 10 wt% $MoO_3/{\gamma}-Al_2O_3$, showed the highest activity for water gas shift reaction. The addition of K retarded the reducibility of cobalt-molybdenum catalysts. It gave, however, good dispersion and large BET surface area to the catalysts which were attributed to the disappearance of polymolybdate clustyer such as $Mo_7O_{24}^{6-}$ and the formation of small Mo$O_4^{2-}$ cluster. It was confirmed by the analyses of pore size distribution, activation energy, Raman spectroscopy, and electron diffraction. The activation energies and the frequency factors of the catalysts 3C10M and 5KC10M (the catalyst added 5 at% K for Mo to the catalyst 3C10M) were 43.1 and 47.8 kJ/mole, and 4,297 and 13,505 $sec^{-1}$, respectively. These values were also well correlated with our suggestion. These phenomena were attributed to the direct interaction between K and CoMo oxides irrelevant to the support.

• Journal of Powder Materials
• /
• v.25 no.4
• /
• pp.322-326
• /
• 2018

The hydrogen reduction behavior of $MoO_3-CuO$ powder mixture for the synthesis of homogeneous Mo-20 wt% Cu composite powder is investigated. The reduction behavior of ball-milled powder mixture is analyzed by XRD and temperature programmed reduction method at various heating rates in Ar-10% $H_2$ atmosphere. The XRD analysis of the heat-treated powder at $300^{\circ}C$ shows Cu, $MoO_3$, and $Cu_2MoO_5$ phases. In contrast, the powder mixture heated at $400^{\circ}C$ is composed of Cu and $MoO_2$ phases. The hydrogen reduction kinetic is evaluated by the amount of peak shift with heating rates. The activation energies for the reduction, estimated by the slope of the Kissinger plot, are measured as 112.2 kJ/mol and 65.2 kJ/mol, depending on the reduction steps from CuO to Cu and from $MoO_3$ to $MoO_2$, respectively. The measured activation energy for the reduction of $MoO_3$ is explained by the effect of pre-reduced Cu particles. The powder mixture, hydrogen-reduced at $700^{\circ}C$, shows the dispersion of nano-sized Cu agglomerates on the surface of Mo powders.

• The Korean Journal of Ceramics
• /
• v.5 no.2
• /
• pp.115-118
• /
• 1999

Carbon composites with $MoSi_2$ dispersion were prepared by hot-pressing at $1700^{\circ}C$ under 30 MPa for 1 h using polysilazance as binding material. The composites consisted of C, $Mo_{4.8}Si_3C_{0.6}$ and SiC. Bulk density and porosity of the carbon composites with 10 vol% $MoSi_2$ was 1.8g.$\textrm{cm}^{-3}$ and 34%, respectively. This composite was oxidized about 0.05mm from the surface of the carbon composite after oxidation test at $1500^{\circ}C$ for 10h in air. Formation of the $SiO_2$ glass layer was observed by SEM. When this composite suffered damage in the coating layer, it had hardly farther oxidation because of its self-repairing property. The composite prepared in this study indicated good oxidation resistance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.6
• /
• pp.558-561
• /
• 2004

The morphology of silica supported $MoO_{3}$ catalysts, which was prepared by impregnation of ammonium heptamolybdate(AHM) with various surface loadings up to 4 atoms $Mo/nm^{2}$, was studied using x-ray diffraction(XRD). All morphologies of silica supported $MoO_{3}$ appear to be thermodynamically driven. For high loaded catalysts there appeared three states: a sintered and well-dispersed hexagonal state at moderate temperature calcination($300^{\circ}C$), and a sintered orthorhombic state at high temperature calcination($500^{\circ}C$). Whereas the sintered orthorhombic phase is detected by XRD at loadings in excess of 1.1 atom $Mo/nm^{2}$, the well-dispersed hexagonal phase is not detected even until 4.0 $atomsMo/nm^{2}$. The higher apparent dispersion of the hexagonal phase may arise from some role of ammonia which results in a stronger $MoO_{3}-SiO_{2}$ surface interaction.

• Korean Journal of Materials Research
• /
• v.31 no.11
• /
• pp.593-600
• /
• 2021

Herein, a series of g-C₃N₄ modified Bi₂MoO₆ nanocomposites using Bi₂MoO₆ and melamine as original materials are fabricated via sintering process. For presynthesis of Bi₂MoO₆ an ultrasonic-assisted hydrothermal technique is researched. The structure and composition of the nanocomposites are characterized by Raman spectroscopy, X-ray diffraction (XRD), and high-resolution field emission scanning electron microscopy (SEM). The improved photoelectrochemical properties are studied by photocurrent density, EIS, and amperometric i-t curve analysis. It is found that the structure of Bi₂MoO₆ nanoparticles remains intact, with good dispersion status. The as-prepared g-C₃N₄/Bi₂MoO₆ nanocomposites (BMC 5-9) are selected and investigated by SEM analysis, which inhibits special morphology consisting of Bi₂MoO₆ nanoparticles and some g-C₃N₄ nanosheets. The introduction of small sized g-C₃N₄ nanosheets in sample BMC 9 is effective to improve the charge separation and transfer efficiency, resulting in enhancing of the photoelectric behavior of Bi₂MoO₆. The improved photoelectronic behavior of g-C₃N₄/Bi₂MoO₆ may be attributed to enhanced charge separation efficiency, photocurrent stability, and fast electron transport pathways for some energy applications.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.391-395
• /
• 2013

In this study, zinc oxide (ZnO) nano powder, well known as an UV absorbing material, was synthesized with three synthetic conditions by the hydrothermal method. After ZnO nano powder was surface-modified with various silane coupling agents to improve dispersion property, a dispersion sol was prepared with dispersant for 72 h by the ball-milling of surface-modified ZnO nano powder. The dispersion sol, prepared by modifying the surface of the ZnO nano powder with an average size of about 30 nm using 3-chloropropyl trimethoxy silane, showed an excellent dispersion stability with a high UV-shielding and visible trnasparency.