• 한국세라믹학회지
• /
• 제37권8호
• /
• pp.817-823
• /
• 2000

A solid-state electrochemicall cell for sensing CO2 gas was fabricated using a solid electrolyte of Li2CO3-Li3PO4-Al2O3 mixture and a reference electrode of LiMn2O4. The e.m.f. (electromotive force) of sensor showed a good accordance with theoretical Nernst slope (n=2) for CO2 gas concentration range of 100-10000 ppm above 35$0^{\circ}C$. The e.m.f. of sensor was constant regardless of oxygen partial pressure at the high temperature above 0.1 atm. It was, however, a little depended on oxygen partial pressure as the pressure decreased below 0.1 atm. The oxygen-dependency of our sensor gradually disappeared as the operating temperature increased. The sensing behavior of our CO2 sensor was affected by the presence of water vapor, but its effect was small comparing with other sensors.

• 한국수소및신에너지학회논문집
• /
• 제27권6호
• /
• pp.670-676
• /
• 2016

Hydrogen town in Republic of Korea was established in 2013. Hydrogen as a byproduct produced by various processes of factories is used in hydrogen town facilities. As cell performance is affected by contaminations in fuel gas, various standards about impurities of fuel have been determined by many countries. This study shows performance degradation of single cell with impurities concentrations. Traces of carbon monoxide (CO) and hydrogen sulfide ($H_2S$)can cause considerable cell performance losses. For comparing the performances by poisoning of CO, acceleration test, I-V curve, constant current are performed. Both the CO and $H_2S$ poisoning rate are a function of their concentration. With the higher concentrations the higher poisoning rates are observed. And, it was confirmed that, oxidation behavior and side reaction generation are not affected. Under the lower $H_2S$ concentration condition, the poisoning rate is much higher than that of CO because of its different adsorption intensity. It can be possible that the result of this study can be used for enacting regulation as a baseline data.

• The Korean Journal of Physiology
• /
• 제6권1호
• /
• pp.1-9
• /
• 1972

In order to observe a possible effect of CO intoxication on the activities of surfactant, the rabbit war exposed either to 0.1, 0.2 and 0.4% CO gas for two to six hours or 0. 1% CO gas for two hours daily for 1, 3 and 5 days, and the lung extract was prepared. The tension-area diagram of the lung extract was recorded automatically using the modified Langmuir-wilhelmy balance with a synchronized recording system, and the results were compared with control (i. e. : non-CO gas exposed normal rabbits). The results obtained are summarized as follows: 1. The maximal and minimal surface tensions, width of the tension-area diagram at the surface area of 40% in lung extract, and stability index of the normal rabbit lung extracts were $31.6{\pm}3.11\;dynes/cm,\;8.2{\pm}0.56\;dynes/cm,\;21.4{\pm}4.40dynes/cm\;and\;1.12{\pm}0.22$, respectively. 2. The activities of surfactant in the CO gas exposed group did not show any significant change from the control. 3. The above results suggest that CO gas produced no noticeable effect on the surfactant system of the lung.

• 한국표면공학회지
• /
• 제49권1호
• /
• pp.75-80
• /
• 2016

$In_2O_3$ nanowires were coated with $Co_3O_4$ nanoparticles to investigate the improvement of ethanol gas sensing performance compared with as-synthesized $In_2O_3$ nanowires. Scanning electron microscopy showed that the nanowires synthesized by VLS mechanism had diameters and lengths of approximately 50-100 nm and a few micrometers, respectively. $Co_3O_4$ nanoparticles produced by hydrothermal method was in the size range of a few to a few tens nm. As-synthesized and $Co_3O_4$ nanoparticles coated $In_2O_3$ nanowires sensors exhibited responses of 1.96% and 4.57%, respectively for the ethanol gas concentration of 200 ppm at $200^{\circ}C$. The underlying mechanism for the improved responses of $Co_3O_4$ nanoparticles coated $In_2O_3$ nanowires sensors is discussed.

• 멤브레인
• /
• 제32권5호
• /
• pp.325-335
• /
• 2022

본 연구에서는 zeolitic imidazolate framework-9 (ZIF-9)을 합성하고 poly(ether-b-amide)-1657 (Pebax-1657) 내에 함량을 달리하여 Pebax/ZIF-9 혼합막을 제조한 다음 단일기체 (N₂, CO₂)를 투과하여 혼합막에 대한 기체 투과 특성을 조사하였다. 순수 Pebax 막 내에 혼입되는 ZIF-9 함량이 증가함에 따라 N₂ 투과도는 점차 감소하고, CO₂ 투과도는 Pebax/ZIF-9 3 wt% 혼합막까지 증가하다가 그 이후의 함량에서는 감소하였다. 그리고 혼합막들 중 Pebax/ZIF-9 3 wt% 혼합막은 극성 기체인 CO₂에 대해 gate-opening 현상이 일어나면서 선택적으로 CO₂를 받아들여 가장 높은 선택도 69.3을 보였다. 또한 CO₂ 투과도와 CO₂/N₂ 선택도가 모두 증가하여 Robeson upper-bound에 가장 근접하는 결과를 얻었다.

• 대한임베디드공학회논문지
• /
• 제11권5호
• /
• pp.299-304
• /
• 2016

As public interest in air quality and environment problem is increasing, many researches are being carried out the gas measurement system. Especially, Non-dispersive infrared (NDIR) measurements using Beer-Lambert gas sensing principle with very high selectivity and long life time are noted for reliable method. It is possible to detect various gases such as carbon dioxide (CO2), carbon monoxide (CO), and nitrogen dioxide (NO2), but many researches are mostly concentrated on CO2 sensor. The multi-gas measuring instrument is high price and unwieldy, therefore it is not suitable for wide area required numerous instrument. So we study the NDIR multi-gas measurement system for air quality based on wireless sensor network, and experiment the realized measurement system.

• 멤브레인
• /
• 제28권4호
• /
• pp.233-242
• /
• 2018

본 연구는 GO (graphene oxide)를 활용한 기체 분리막 연구를 위해 PEBAX [poly(ether-block-amide)]에 GO를 첨가하여 PEBAX-GO 고분자 복합막을 제조하고, 이 복합막을 통해 $H_2$, $N_2$, $CH_4$, $CO_2$에 대한 기체투과 특성을 연구하였다. 기체투과 실험결과 PEBAX-GO 복합막에 대해 $N_2$, $CH_4$, $CO_2$의 기체투과도는 GO 함량이 증가함에 따라 점차 감소하였다. 반면 $H_2$의 기체투과도는 GO 함량이 증가함에 따라 증가하였고, GO 함량 30 wt%에서는 21.43 barrer로 단일막에 비하여 약 5배가 증가하였는데 GO는 $H_2$에 대해 다른 기체들에 비해 빠르고 선택적인 기체운송 channel로 더 용이하게 작용하였기 때문이다. 증가된 선택도($H_2/N_2$)와 선택도($H_2/CH_4$)는 투과기체 크기에 의한 확산선택도가, 증가된 선택도($CO_2/N_2$)와 선택도($CO_2/CH_4$)는 $CO_2$와 GO의 -COOH와의 친화성으로 용해선택성이 더 크게 영향을 미친 것으로 나타났다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.707-714
• /
• 2007

The heat transfer coefficient and Pressure drop during gas cooling process of $CO_2$ (R-744) in inclined helical coil copper tubes were investigated experimentally. The main components of the refrigerant loop are a receiver. a variable-speed pump. a mass flow meter, a pre-heater and a inclined helical coil type gas cooler (test section). The test section consists of a smooth copper tube of 2.45mm inner diameter. The refrigerant mass fluxes were varied from 200 to $600[kg/m^2s]$ and the inlet Pressures of gas cooler were 7.5 to 10.0 [MPa]. The heat transfer coefficients of $CO_2$ in the inclined helical coil tubes increases with the increase of mass flux and gas cooling pressure of $CO_2$. The pressure drop of $CO_2$ in the gas cooler shows a relatively good agreement with those Predicted by Ito's correlation developed for single-phase in a helical coil tube. The local heat transfer coefficient of $CO_2$ agrees well with the correlation by Pitla et al. However, at the region near pseudo-critical temperature. the experiments indicate higher values than the Pitla et al. correlation. Therefore. various experiments in the inclined helical coil tubes have to be conducted and it is necessary to develop the reliable and accurate prediction determining the heat transfer and pressure drop of $CO_2$ in the inclined helical coil tubes.

• 멤브레인
• /
• 제4권4호
• /
• pp.197-204
• /
• 1994

본 연구에서는 hollow fiber 막모듈을 통한 순수 $CH_4,\;CO_2$기체와 $CH_4/CO_2$ 혼합기체의 투과 특성을 살펴 보고, 이를 모사값과 비교하여 보았다. 순수 기체의 투고율은 온도에 따라 Arrhenius type으로 증가하였으며, 활성화에너지는 $CO_2$는 6.61kJ/mol, $CH_4$는 25.26kJ/mol로 나타났다. 혼합기체의 투과에 있어서 투과부의 유량과 $CO_2$ 조성, 그리고 배제부의 $CH_4$조성은 cut의 증가에 따라 증가하였다. 분리인자는 5~20atm의 압력과 cut이 20으로 고정된 상태에서 20~40의 범위에 있었으며, 압력이 증가하고 온도가 감소할수록 증가하는 경향을 나타내었다. 실험결과와 모사결과는 투과부 유량과 $CO_2$조성의 경우 8% 이내에서, 배제부의 $CH_4$조성의 경우 15% 이내에서 일치하였다.

• 자원리싸이클링
• /
• 제29권3호
• /
• pp.3-10
• /
• 2020

일메나이트의 선택염화를 통해 제조한 합성루타일을 유동층에서 CO와 Cl₂ 혼합가스를 이용하여 염화시켜 TiO₂의 염화반응 속도에 미치는 반응 온도, 시간, CO가스와 Cl₂가스의 분압 비($p_{Cl_2}/p_{CO}$)의 영향에 대하여 조사하였다. $p_{Cl_2}/p_{CO}$가 높을 때 TiCl₄의 전환율은 감소하였으며, 화학양론 계산결과와 실험결과를 비교하였을 때 Cl₂가스 보다 CO가스의 분압이 더 큰 영향을 미친 것으로 판단되었다. 따라서 실험 결과를 입자의 기공을 고려한 모델에 대입하였을 때 합성 루타일의 염화반응은 화학반응율속으로 결정되었고, 활성화에너지는 53.77 kJ/mol로 계산되었다.