• Journal of the Korean Ceramic Society
• /
• v.24 no.1
• /
• pp.63-69
• /
• 1987

Effect of MoO3 additiion on the semiconductive BaTiO3 ceramics doped with 0.2 mole% Nb2O5 and their frequency characteristics have been investigated on the view of intergranular barrier layer model through the observation of changes in their electrical properties. The resistivity increases with the increase of MoO3 addition, but the capacitance, the frequency dependence of capacitance and the effect of positive temperature coefficient of resistivity (PTCR) decrease. It is explained by the possible increase in the thickness of potential barrier due to the formation of insulating layer and thus decrease in the degree of energy band bending. Both the PTCR effect and resistivity decrease with the increase of frequency due to the possible elimination of barrier layer at the grain boundary.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.2
• /
• pp.36-36
• /
• 2001

간섭계를 이용하는 작업에서 가장 중요한 요구사항은 간섭 필드의 안정성을 높게 유지하는 것이며 이는 안정된 간섭패턴을 이용한 측정에 있어서 정밀성을 확보해 준다. 그러나 진동과 같은 위상잡음에 의해 안정성을 유지하기 힘들다. 본 논문에서는 BaTiO₃의 SPPCM 특성을 이용하여 마흐젠더 간섭계와 같은 전통적인 간섭계 측정시 발생 가능한 위상잡음의 영향을 줄여 안정된 간섭 패턴 확보 방법을 제안하였다. 또한 BaTiO₃로 빛을 입사시킬 때 구형렌즈를 기울여 입사빔을 원형이 아닌 타원형으로 입사시켜 원형 입사의 경우에 비해 SPPCM의 응답시간과 반사율을 개선하였다. 그리고 실험을 통해 결과를 확인하였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.4
• /
• pp.398-404
• /
• 1989

Optical pattern recognition system using real-time hologram mechanism in a photorefractive $BaTiO_2$ single crystal is analyzed and experimented. Edge enhancement technique is introduced for enhancing pattern discrimination capability, and patterns can be recognized within 8 sec with 5.5mW low incident light intensity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12
• /
• pp.1080-1086
• /
• 2003

Effects of E$_2$O$_3$. HO$_2$O$_3$ and Dy$_2$O$_3$ addition on dielectric properties of non-reducible BaTiO$_3$ based X7R dielectrics with Ni electrode have been studied in a reduced atmosphere. As the content of rare-earth with E$_2$O$_3$. HO$_2$O$_3$, Dy$_2$O$_3$ was less than 3wt%, The TCC(Temperature Capacitance Change) and insulation resistance characteristics were improved by compensate the oxygen vacancies due to occupy either the Ba or Ti site. We developed the composition of X7R (EIA standard) for higher capacitance MLCC which had high reliability electric properties by the addition of Er ion into BaTiO$_3$ + MgO + Y2O$_3$ + MnO + (Ba$\sub$0.4/Ca$\sub$0.6/)SiO$_3$ composition.

• Membrane Journal
• /
• v.22 no.1
• /
• pp.8-15
• /
• 2012

Tubular $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ membranes with $La_{0.6}Sr_{0.4}Ti_{0.3}Fe_{0.7}O_{3-{\delta}}$ porous coating layer were prepared by extrusion and dip coating technique. XRD and SEM result showed the tubular membrane possessed the perovskite structure and porouscoating layer (thickness= about $2{\mu}m$) in surface. The oxygen permeation test was measured at condition of ambient air (feed side) and vacuum (permeate side) in the temperature range from 750 to $950^{\circ}C$. The oxygen permeation flux of $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ tubular membrane with $La_{0.6}Sr_{0.4}Ti_{0.3}Fe_{0.7}O_{3-{\delta}}$ porous coating layer reached maximum $3.2mL/min{\cdot}cm^2$ at $950^{\circ}C$ and was higher than non-coated $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ tubular membrane. Long-term stability test result indicated that the oxygen permeation flux was quite stable during the 11 day.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.7-9
• /
• 2006

$(BaSr)TiO_3$ thick films were prepared by tape casting method using $BaTiO_3$ and $SrTiO_3$ powder slurry in order to investigate dielectric properties and low temperature sintering. Sintering density was $5.7\;g/cm^3$ and the BST sample exhibited the maximum dielectric constant, tunability at temperatures near phase transition point. The dielectric constant was increased and curie temperature was shifted to higher temperature with increasing of annealing temperature.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1516-1519
• /
• 1996

In this paper, a study on the electrical properties of ternary compound ceramics $[(1-y-x)BaTiO_{3}-ySrTiO_{3}-xMgTiO_3]$ fabricated 7 samples with each mol[%] by using the mixed oxide method. In this case, the sintering temperature were at $1,250[^{\circ}C]$ for 2[hr]. Also made ceramic capacitors from 7 samples, temperature coefficient of the capacitance and the variation of relative dielectric constants and loss with fixed frequency (1KHZ) were studied. In some ceramic capacitors, has shown very good properties of the dielectric constants and loss. In case of BSM-11 ceramic capacitor, is sure to the commercial capacitor which shows steady properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.251-254
• /
• 1998

The ($0.8BaTiO_3-0.1SrTiO_3-0.1MgTiO_3$)+$0.006Nb_2O_5$ ceramics were fabricated by conventional ceramic process. The dielectric property of specimen was investigated that the specimen was sintering temperature at 1,300C for 3hours and then annealed at $1,100^{\circ}C$ for 3hours in a atmosphere (air) to be painted on the surface with CuO paste. The results of the temperature and frequency are varied, the dielectric constant and loss tangent are unsuitable for BL capacitor. The dielectric constants were varied to be negative temperature coefficient(2.000-3,000) in the temperature range between -10 and $140^{\circ}C$, the dissipation factors (tan $\delta$) were some high(0.1-0.3). It was not grain insulation, in cause of the some difficult to be annealed temperature with CuO paste and fired atmosphere. But, we have some different annealing temperature and fired atmosphere, it will be suitable BL(Boundary Layer)capacitor.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.2
• /
• pp.122-127
• /
• 2001

The high stability of the interference pattern is very important in the case of measuring interference when a phase noise like a vibration occurs in the measuring environment. In this paper, we proposed the method of phase noise filtering by BaTiO$_3$ with the characteristic of SPPCM. Also, a beam with a shape of an ellipse was incident into BaTiO$_3$ by using the tilted lens so as to improve the reflectivity and the response time. And we confirmed the result by optical experiment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.31-34
• /
• 2006

In this study, $(Ba_{0.7}\;Sr_{0.3})TiO_3$ was coated on Pt/Ti/$SiO_2$/Si wafer by using Sol-Gel method. Coating process was repeated 3~5 times and then sintered at 750[$^{\circ}C$] for 1 hour. Each specimen was analyzed structure and electrical characteristics. In structure characteristics, EDX analyzed the samples ratio of the formation on the structural property. Thermal behavior was observed with TG-DTA and concluded that the heat-treatment of the samples was degreed 750[$^{\circ}C$]. Surface and section of thin films were observed with SEM.