• 한국세라믹학회지
• /
• 제53권1호
• /
• pp.81-86
• /
• 2016

The effect of substrate rotation speed on the phase forming behavior and microstructural variation of 8 wt% yttria ($Y_2O_3$) stabilized $ZrO_2$ (8YSZ) coatings as a thermal barrier coating has been investigated. 8YSZ coatings with $100{\sim}200{\mu}m$ thickness were deposited by electron beam-physical vapor deposition onto a super alloy (Ni-Cr-Co-Al) substrate with a bond coating (NiCo-CrAlY). The width of the columnar grains of the 8YSZ coatings increased with increasing substrate rotation speed from 1 to 30 rpm at a substrate temperature range of $900{\sim}950^{\circ}C$. In spite of the different growth behaviors of coatings with different substrate rotation speeds, the phases of each coating were not changed remarkably. Even after post heat treatments with various conditions of the coated specimens fabricated at 20 rpm, only a change of color was noticeable, without any remarkable change in the phase or microstructure.

• 한국해양공학회지
• /
• 제13권1호통권31호
• /
• pp.62-69
• /
• 1999

67Ni-22Cr-10Al-1Y and $ZrO_2-8Y_2O_3$ were coated on the substrate surface of ST304 and Al2024 by the plasma spraying method. The adgesion of the films varies depending on the substrates and the laminating method. In the case of STS304, the cracks were observed at thermal shock temperature difference ${Delta}T$ of $900^{circ}C$ in the non functionally gradient material(NFGM) and at $1100^{circ}C$ in the functionally gradient material(FGM). The film adhesion of the FGM is better than that of the NFGM in ST304. The cumulative AE count of the FGM of STS304 increased continuously at the bending test. But the NFGM of STS304 showed discontinuity of the AE count. The total AE count for the FGM of STS304 decreased as the number of thermal shock increased, and this tendency was evident as the thermal shock temperature difference increased.

• 환경위생공학
• /
• 제9권2호
• /
• pp.8-23
• /
• 1994

During the period from Mar., 1991 to Feb., 1992 66 tSP samples were collected by Hi volume air sampler at 1 sampling site in Seoul and the amount of concentration of 21 components(SO$_{4}$$^{2-}$, NO$_{3}$$^{-}$, NH$_{4}$$^{+}$, Cl$^{-}$, Al, Ba, Ca, Cd, Cr, Cu, Fe, It Mg, Mn, Na, Ni, Pt Si, Ti, Zn, Zr ) were measured. And monthly and seasonal variation were surveyed and the principal component analysis( PCA ) were carried out with respect to these amount of pollutants, minimum of visibility and radiation on a horizontal surface. The total amount of soluble ion in water was high in order o(SO$_{4}$$^{2-}$> NO$_{3}$$^{-}$> N%'>Cl$^{-}$ and metal ion was high in order of Na> Ca>Si> Fe> Al> K> Mg> Zn> Pb> Cu>Ti> Mn > Ba> Cr> Zr> Ni> Cd. There was Seasonal variation in concentration for SO$_{4}$$^{2-}$, NH$_{4}$$^{+}$, Cl$^{-}$, Na, Al, Ca, Bt Mg, Fe and Si. It was assumed that the components of the highest concentration on April were depend on yellow sand and the frequency of wind velocity and direction. As the results of PCA, the amount of pollution components was able to characterized with two principal components(Z$_{1}$, Z$_{2}$ ). The first principal components Z$_{1}$ was considered to be a factor indicating the pollutants originated from natural generation and The second principal components Z$_{2}$ was considered to be a factor indicating the pollutants originated from human work. The monthly concentration of pollutants in ISP, minimum of visibility and radiation on a horizontal surface was possible to evaluate by the use of these two principal components Z$_{1}$ and Z$_{2}$ .

• Journal of Welding and Joining
• /
• 제32권1호
• /
• pp.40-46
• /
• 2014

Bonding technology and bonding mechanism of metal to ceramic including brazing, diffusion bonding, friction welding and etc were reviewed in this study. Various factors should be considered from a bonding design step to acquire a good bonding joint because of a large difference between metal and ceramic in crystal lattice, coefficient of thermal expansion and various properties. In addition, metal and ceramic bonding technologies are constantly being developed according to precise components, multi-function and application to harsh environment. However, improvement of bonding properties and bonding reliability also should be accompanied. Bonding of ceramics, such as $ZrO_2$, $Ti_3AlC_2$ and SiC, to metals like Ti-alloy, TiAl and steel were described in this paper.

• Journal of Electrical Engineering and Technology
• /
• 제10권4호
• /
• pp.1621-1625
• /
• 2015

Power quality has always been a concern of power engineers. Certainly an argument can be successfully made that most parts of power engineering have the ultimate objective to improve power quality. AC motors were widely used in industrial and domestic applications. Generally, AC motors were of two types: Induction and Synchronous motors. In motor many parameters like different load cycling, switching, working in hot weather and unbalances creates harmonics which creates major reasons for temperature rise of the motors. Due to high peak value of voltage, harmonics can weaken insulation in cables, windings and capacitors and different electronic components. Higher value of harmonics increase the motor current and decrease the power factor which will reduce the life time of the motor and increase the overall rating of all electrical equipments. Harmonics reduction of all the motors in India will save more power. Coating of windings of the motor with nano fillers will reduce the amount of harmonics in the motor. Based on the previous project works, actions were taken to use the enamel filled with various nano fillers for the coating of the windings of the different AC motors. Ball mill method was used to convert the micro particles of Al₂O₃, SiO₂, TiO₂, ZrO₂ and ZnO into nano particles. SEM, TEM and XRD were used to augment the particle size of the powder. The synthesized nano powders were mixed with the enamel by using ultrasonic vibrator. Then the enamel mixed with the nano fillers was coated to the windings of the several AC motors. Harmonics were measured in terms of various indices like THD, VHD, CHD and DIN by using Harmonic analyzer. There are many other measures and indices to describe power quality, but none is applicable in all cases and in many instances, these indices may hide more than they show. Sometimes power quality indices were used as a basis of comparison and standardization. The efficiency of the motors was increased by 5 – 10 %. The thermal withstanding capacity of the motor was increased by 5º to 15º C. The harmonics of the motors were reduced by 10 – 50%.

• 한국자기학회지
• /
• 제16권2호
• /
• pp.136-139
• /
• 2006

자기터널접합은 일반적으로 $250^{\circ}C$ 이상의 온도에서 터널자기저항비의 저하가 발생하는데 이는 반강자성체로 사용된 IrMn 중 Mn이 강자성체인 CoFe 및 터널배리어로의 내부확산에 기인한다. 자기터널접합의 열적 안정성을 향상시키기 위하여 나노산화층을 삽입하여 Mn의 확산을 제어하였다. CoNbZr 4/CoFe 10/IrMn 7.5/CoFe 3/터널배리어/CoFe 3/CoNbZr 2(nm)와 같은 자기터널접합을 기본구조로 하여 각각의 층에 나노산화층을 삽입하여 열적안정성 및 전자기적 특성을 비교 분석 하였다. 나노산화층의 삽입에 의해 터널자기저항비, 자기터널접합의 표면 평활도 및 열적안정성이 향상되었다.

• 한국세라믹학회지
• /
• 제43권6호
• /
• pp.369-375
• /
• 2006

[ $(Ba_{0.5}Sr_{0.5})_{0.99}Co_{x}Fe_{1-x}O_{3-{\delta}}$ ] [x=0.8, 0.2](BSCF) powders were synthesized by a Glycine-Nitrate Process (GNP) and the electrochemical performance of the BSCF cathode on a scandia stabilized zirconia, $[(Sc_{2}O_3)_{0.11}(ZrO_2)_{0.89}]-1Al_{2}O_3$ was investigated. In order to prevent unfavorable solid-state reactions between the cathode and zirconia electrolyte, a GDC ($Gd_{0.1}Ce_{0.9}O_{2-{delta}}$) buffer layer was applied on ScSZ. The BSCF (x = 0.8) cathode formed on GDC(Buffer)/ScSZ(Disk) showed poor electrochemical property, because the BSCF cathode layer peeled off after the heat-treatment. On the other hand, there were no delamination or peel off between the BSCF and GDC buffer layer, and the BSCF (x = 0.2) cathode exhibited fairly good electrochemical performances. It was considered that the observed phenomenon was associated with the thermal expansion mismatch between the cathode and buffer layer. The ohmic resistance of the double layer cathode was slightly lower than that of the single layer BSCF cathode due to the incorporation of platinum particle into the BSCF second layer.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.30.1-30.1
• /
• 2009

정보화가 급속히 진전됨에 따라 보다 많은 양의 정보를 전송, 처리, 저장하게 되면서 이를 위해 대용량, 고속, 비휘발성의 특징을 갖는 차세대 메모리의 개발이 절실히 요구되고있다. 이 중 저항 변화 메모리(ReRAM)는 일반적으로 TiO2, Al2O3, NiO2, HfO2, ZrO2 등의 전이금속산화물을 이용한 MIM 구조로서 적당한 전기 신호를 가하면 저항이 높아서 전도되지 않는 상태(Offstate)에서 저항이 낮아져 전도가 가능한 상태(On state)로 바뀌는 메모리 특성을가진다. ReRAM은 비휘발성 메모리이며 종래의 비휘발성 기억소자인 Flash memory 보다 access time 이105 배 이상 빠르고, 5V 이하의 낮은 전압에서도 동작이 가능하다. 또한 구조가 간단하여 공정 단순화가 가능하고 소자의 집적화도 쉽다는 점 등 많은 장점들이 있어서 Flash memory를 대체할 수 있는 유력한 후보로 여겨지고 있다. 본연구에서는 DC-magnetron Sputtering 방법으로 전이금속 박막을 증착하고, Dry furnace로 산화시켜 전이금속산화물 박막을 제작한 후 저항변화 특성을 연구하였다. 두 개의 전이금속산화물 박막을 dual-layer로 형성시켜 저항변화특성을 관찰하였으며 또한, 전이금속산화물 박막의 조성을 달리 하여 저항변화를 관찰 하였다. 전이금속산화물 박막의 전기적 특성을 알아보기 위해 Si(100) wafer 위에 Pt를 이용 MIM 형태로 capacitor 시편을 제작 하여, probe station으로 I-V 측정을 하였고 조성 및 표면 분석을 위해서는 AES와 AFM을, 미세구조를 분석을 위해서는 TEM과 SEM 을 사용하였다.

• 한국지구과학회:학술대회논문집
• /
• 한국지구과학회 2005년도 추계학술발표회 논문집
• /
• pp.136-141
• /
• 2005

The K Ar ages, whole rock geochemistry and Sr Nd Pb isotopes have been determined for the submarine basalts dredged from the P2 and P3 segments of the Antarctic-Phoenix Ridge (APR), Drake Passage, Antarctica, for better understanding on temporal variation of magma chemistry in association with extinction of seafloor spreading. The fossilized APR is distant from the known hot spots, and consists of older N-MORB prior to extinction of spreading and younger E-MORB after extinction. The older N-MORB (3.5-6.4 Ma) occur in the southeast flank of the P3 segment (PR3) and the younger E-MORB (1.4-3.1 Ma) comprise a huge seamount at the P3 segment (SPR) and a big volcanic edifice at the P2 segment (PR2). The N-type PR3 basalts have higher Mg#, K/Ba, and CaO/Al2O3 and lower Zr/Y, Sr, and Na8.0 with slight enrichment in incompatible elements and almost flat REE patterns. The E-type SPR and PR2 basalts are highly enriched in incompatible elements and LREE. The extinction of spreading occurring at 3.3 Ma seems to have led to a temporal magma oversupply with E-MORB signatures. Geochemical signatures such as Ba/TiO2, Ba/La, and Sm/La suggest heterogeneity of upper mantle and formation of E-MORB by higher contribution of enriched materials to mantle melting, compared to N-MORB environment. E-MORB magmas beneath the APR seem to have been produced by low melting degree (up to 1% or more) at deeper low-temperature regime, where metasomatized veins consisting of pyroxenites have preferentially participated in the melting. The occurrence of E-MORB at the APR is a good example to better understand what kinds of magmatism would occur in association with extinction of spreading.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.168-168
• /
• 2008

Dimension of a transistor has rapidly shrunk to increase the speed of device and to reduce the power consumption. However, it is accompanied with several problems like direct tunneling through the gate dioxide layer and low conductivity characteristic of poly-Si gate in nano-region. To cover these faults, study of new materials is urgently needed. Recently, high dielectric materials like $Al_2O_3$, $ZrO_2$, and $HfO_2$ are being studied for equivalent oxide thickness (EOT). However, poly-Si gate is not compatible with high-k materials for gate-insulator. Poly Si gate with high-k material has some problems such as gate depletion and dopant penetration problems. Therefore, new gate structure or materials that are compatible with high-k materials are also needed. TiN for metal/high-k gate stack is conductive enough to allow a good electrical connection and compatible with high-k materials. According to this trend, the study on dry etching of TiN for metal/high-k gate stack is needed. In this study, the investigations of the TiN etching characteristics were carried out using the inductively coupled $BCl_3$-based plasma system and adding $Cl_2$ gas. Dry etching of the TiN was studied by varying the etching parameters including $BCl_3$/Ar gas mixing ratio, RF power, DC-bias voltage to substrate, and $Cl_2$ gas addition. The plasmas were characterized by optical emission spectroscopy analysis. Scanning electron microscopy was used to investigate the etching profile.