Sn doped $In_2O_3$ (ITO) and ITO/Cu/ITO (ICI) multilayer films were prepared on glass substrates with a reactive radio frequency (RF) magnetron sputter without intentional substrate heating, and then the influence of the Cu interlayer on the methanol gas sensitivity of the ICI films were considered. Although both ITO and ICI film sensors had the same thickness of 100 nm, the ICI sensors had a sandwich structure of ITO 50 nm/Cu 5 nm/ITO 45 nm. The ICI films showed a ten times higher carrier density than that of the pure ITO films. However, the Cu interlayer may also have caused the decrement of carrier mobility because the interfaces between the ITO and Cu interlayer acted as a barrier to carrier movement. Although the ICI films had two times a lower mobility than that of the pure ITO films, the ICI films had a higher conductivity of $3.6{\cdot}10^{-4}\;{\Omega}cm$ due to a higher carrier density. The changes in the sensitivity of the film sensors caused by methanol gas ranging from 50 to 500 ppm were measured at room temperature. The ICI sensors showed a higher gas sensitivity than that of the ITO single layer sensors. Finally, it can be concluded that the ICI film sensors have the potential to be used as improved methanol gas sensors.
Highly c-axis oriented Zinc oxide (ZnO) films were successfully deposited at room temperature by oxygen ion-assisted pulsed filtered vacuum arc. The effect of oxygen gas ratio ($O_{2}/O_{2}+Ar$ on the preferred orientation, surface morphology and resistivity of the ZnO films were investigated. Highly crystalline ZnO films with (002) orientation were obtained at over $13\%$ of oxygen gas ratio. Increasing oxygen gas ratio up to $80\%$ was found to improve crystallinity of the films. From hall measurements, it was found that the film has n-type characteristic and carrier concentration and its mobility were closely related with oxygen gas ratio. Minimal resistivity of $3.6{\times}10^{-3}{\Omega}{\cdot}cm$ was obtained in the range of $20\%$ to $40\%$ of oxygen gas ratio.
Boom sprayers have been known by their excellency in field efficiency worker’s safety and pest control efficacy. The boom sprayer in Korea that was developed for paddy field is not suitable for upland field of which shape is irregular and inclination is steep, due to heavy chemical tank long boom width and manual on-off control of spraying. The goal of the study was to develope a boom control system that could control boom angles of left and right boom automatically and independently corresponding to local field slope. The prime mover was selected as a cultivating tractor. Main results of this study were as follows. 1. Ultrasonic sensor whose response time was 0.1s and response angle was within $\pm$20$^{\circ}$was selected to measure distance. Voltage output of the sensor(X, Volt) had a highly significant linear relationship with the vertical distance between the sensor and ground surface(Y, mm) as follows; Y=0.0036X-0.437 2. Left and right section of the boom could be folded up by a position control device(on-off control) which could control the left and right boom independently corresponding to local slope by equalizing distances between the sensor and boom at the center and left/right boom. Most reliable DB(dead band) was experimentally selected to be 75$\Omega$(6cm). 3. At traveling velocity of 0.3~0.5m/s RMS of error between desired and achieved height was less than 4.5cm The developed boom angle controller and boom linkage system were evaluated to be successful in achieving the height control accuracy target of $\pm$10cm.
Inp 소자를 이용하여 광섬유 온도 센서를 제작하고 InP센서의 기초 광흡수단의 이동특성을 조사하였다. 그 결과를 일반 반도체의 흡수계수에 적용하여 InP 소자의 광흡수 계수(${\Omega}$)를 유도하였다. 광흡수 계수와 InP 센서소자의 두께 파라미터를 전달특성에 대입하여 온도변화에 따른 기초 광흡수단 가장자리의 이동특성을 세점의 온도($249^{\circ}K$, $298^{\circ}K$, $369^{\circ}K$)에서 컴퓨터로 계산하고 실험 결과와 비교하였다. 그 결과 InP 소자의 기초 광흡수단이 온도에 비례하여 장파장 영역으로 이동하였으며 단위 온도 상승시 광흡수단의 이동거리는 약 0.42 nm / $^{\circ}K$ 였다. 또 반도체 소자의 두께가 증가할수록 광 파워 밀도 곡선이 낮은 온도로 이동하였다.
This research was aimed to examine the effect of Polygoni Multiflori Radix extract on the blood pressure in spontaneous hypertensive rat (SHR) and norepinephrine - induced arterial contraction in rabbit. In order to investigate the effect of Polygoni Multiflori Radix on rabbit's contracted vascular ring detached from common carotid artery, vascular ring with intact or damaged endothelium was used for the experiment using organ bath. To analyze the mechanism of Polygoni Multiflori Radix-induced relaxation, Polygoni Multiflori Radix extract was infused into contracted vascular ring which had been pretreated by $N{\omega}$-nitro-L-arginine(L-NNA), Methylene blue(MB), and $Ca^{2+}$ was infused into contracted vascular ring induced by NE after treatment of Polygoni Multiflori Radix extract in $Ca^{2+}$-free solution. The results were as follows: Systolic blood pressure was significantly attenuated by administration of Polygoni Multiflori Radix. Blood flow and aldosterone were significantly decreased, but velocity and renin were not affected by Polygoni Multiflori Radix. Polygoni Multiflori Radix had an effective relaxation to the contracted vascular ring by NE in 0.03 mg/ml, 0.1 mg/ml and 0.3 mg/ml level. Polygoni Multiflori Radix had an effective relaxation to the intact endothelium vascular ring, but when endothelium was removed, vascular ring did not relax. Polygoni Multiflori Radix-induced relaxation was inhibited by the pretreatment of L-NNA and MB. Pretreatment of Polygoni Multiflori Radix extract inhibit the contraction by influx of extra-$Ca^{2+}$ in contracted vascular ring induced by NE in $Ca^{2+}$-free solution. As mentioned above, we suggest that Polygoni Multiflori Radix relaxes vascular ring through suppress influx of extra-cellular $Ca^{2+}$ by the action of nitric oxide from endothelium.
Transparent conduction oxides (TCOs) films is extensively reported for optoelectronic devices application such as touch panels, solar cells, liquid crystal displays (LCDs), and organic light emitting diodes(OLEDs). Among the many TCO film, indium tin oxide(ITO) is in great demand due to the growth of flat panel display industry. However, indium is not only high cost but also its deposits dwindling. Therefore, many studies are being done on the transparent conductive oxides(TCOs). We fabricated a target of IZTO(In2O3:ZnO:SnO2=70:15:15 wt.%) reduced indium. Then, IZTO thin films were deposited on glass substrates by pulsed DC magnetron sputtering with various oxygen flow ratio. The substrate temperature was fixed at the room temperature. We investigated the electrical, optical, structural properties of IZTO thin films. The electrical properties of IZTO thin films were dependent on the oxygen partial pressure. As a result, the most excellent properties of IZTO thin films were obtained at the 3% of oxygen flow rate with the low resistivity of $7.236{\times}10^{-4}{\Omega}cm$. And also the optical properties of IZTO thin films were shown the good transmittance over 80%. These IZTO thin films were used to fabricated organic light emitting diodes(OLEDs) as anode and the device performances studied. The OLED with an IZTO anode deposited at optimized deposition condition showed good brightness properties. Therefore, IZTO has utility value of TCO electrode although it reduced indium and we expect it is possible for the IZTO to apply to flexible display due to the low processing temperature.
We have considered the influence of electron irradiation energy of 300, 600 and 900 eV on the stuctural, electrical and optical properties of GZO/$TiO_2$ thin films prepared with RF magentron sputtering. The optical transmittance and electrical resistivity of the films were dependent on the electron's irradiation energy. The electron irradiated GZO/$TiO_2$ films at 900 eV are grown as a hexagonal wurtzite phase and the resistivity is decreased with electron irradiation energy. The GZO/$TiO_2$ films irradiated at 900 eV shows the lowest resistivity of $4.3{\times}10^{-3}{\Omega}cm$. The optical transmittance in a visible wave length region also increased with the electron irradiation energy. The film that electron irradiated at 900 eV shows 82% of optical transmittance and higher work function of 5.18 eV in this study.
마이크로컴퓨터 코오지 배양시설을 제작하여 배양실내의 온도, 상대습도를 계측하고 코오지의 무게를 공정제어 대상으로 공정의 자동화를 시도하였다. 코오지 무게변화는 외팔보형 strain gauge 무게감응장치로 코오지 및 배양실의 온도는 백금저항선$(Pt,\;100\Omega)$ 센서로 계측하였다. 계측신호는 디지털화하여 MC6821 접속소자를 통해 마이크로컴퓨터로 입력되었다. 코오지 무게계측치를 공정의 제어대상으로 할 때 디지탈값(Y)과 코오지의 무게(W,g) 사이의 관계는 Y=0.310W+32.329(r=0.99989)이었다. 배양실내의 온도제어는 폐회로방식에 의하여 on/off로 이루어졌으며 습도제어는 계측된 건, 습구 온도값으로부터 계산된 습도값을 기준으로 살균수의 분무로 수행되었다.
질소 등을 GST225 상변화재료에 첨가시켜 비저항을 증가시킴으로서 PCRAM의 동작 전류를 감소시킨 연구가 선행된 바 있다. 본 연구에서는 GST225와 달리 고속 동작 특성을 갖는 것으로 널리 알려진 Ge-doped SbTe (GeST) 상변화 재료에 Carbon을 첨가하여 박막 특성을 연구하여 동작 전류 감소의 가능성을 타진하였다. 실험을 위한 박막 제작을 위해 2 inch size의 GeST 및 C doped GeST (C-GeST) single target을 이용하여 RF magnetron co-sputtering 하였다. 박막은 carbon이 첨가되지 않은 GeST와 carbon 첨가량이 늘어나는 순서로 C-GeST 1, C-GeST 2, C-GeST 3로 구성된다. 이 때 제작한 박막의 composition analysis를 위해 XRF/RBS/AES가 사용되었고 제작된 박막의 기본적인 특성평가를 위해 resistivity(${\rho}$)와 crystallzation temp.(Cx), surface morphology(AFM), x-ray diffraction pattern(XRD)를 측정하였다. 실험결과 GeST, C-GeST 1, C-GeST 2, C-GeST 3 박막의 Cx는 각각 209, 225, 233, $245^{\circ}C$로 측정되어 carbon 첨가량이 증가됨에 따라 결정화 온도가 증가되는 것을 알 수 있었다. 또한 ${\rho}$도 마찬가지로 annealing 온도를 약 $320^{\circ}C$로 할 경우 ${\rho}$(as-dep)와 ${\rho}$(crystalline) 모두 0.03 / $2.61*10^{-6}$, 0.08 / $7.93*10^{-6}$, 0.09 / $11.99*10^{-6}$, 0.13 / $13.49*10^{-6}{\Omega}{\cdot}m$로 증가하였다. 증가된 ${\rho}$의 원인이 박막의 grain size의 감소라고 단언 할 수는 없으나 AFM 측정결과 grain이라고 추측되는 박막 feature들의 size가 점차 감소하는 것을 확인하였다.
찹쌀가루와 메주가루의 배합비율(무게비)을 달리한 고추장(찹쌀가루 : 메주가루 = 1:1, 1:2, 1:3, 2:1, 3:1)의 숙성 중 품질 변화를 평가하기 위해 12주 동안 숙성시키면서 고추장의 이화학적 특성, 효소 활성 및 레올로지 특성을 연구하였다. 숙성 중 고추장의 수분함량은 $47.4{\sim}47.9%$에서 점차 증가하여 8주에는 최대 수분함량을 보였다. 환원당 함량은 $2{\sim}4$주에 가장 높았으며 이후에서는 점차 감소하는 경향을 보였다. 아미노태 질소 함량은 지속적으로 증가하였다. ${\alpha}-amylase$와 ${\beta}-amylase$ 활성은 숙성 $2{\sim}4$주에 최대 역가를 나타냈다. Acidic protease와 neutral protease는 각각 숙성 2주와 4주에 가장 높은 활성을 보였다. Power law 모델에 의한 유동성 측정에서 고추장은 낮은 유동성지수(flow behavior index, $n=0.21{\sim}0.36$)를 가진 전단담화(shearing-thinning)거동을 보여주었으며, 점조도 지수(consistency index, K)와 겉보기점도 $({\eta}_{a,10})$는 숙성 2주에 급격히 증가하고 이후에는 감소하였다. Casson 모델식에 의한 항복응력$({\sigma}_{oc})$은 숙성 2주에 급격히 증가하고 이후에는 감소하였다. 동적 점탄성 측정에서는 저장 탄성률 (G#)이 손실탄성률 (G') 보다 높은 수치를 나타내었고 주파수(frequency, ${\omega}$)가 증가함에 따라 증가하는 경향을 보여주었다. 또한 숙성기간이 경과함에 따라 (G#)과 (G@)이 증가하는 경향을 나타냈다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.