Complex dynamic relaxation processes of mechanical as well as dielectric character in polymeric anelastic solids are closely related through the movement of molecular chain segment in morphological structure, and the morphology can easily be modified by the treatments such as mechanical drawing or irradiation, those of which result, in turn, the complicated change on the appearance of the observed complex relaxation peak. In order to extract any meaningful understanding from the modified appearance of the peak, the relaxation peak must be resolved into the sum of the dynamic single relaxation peaks, each of which can be characterized respectively by three factors such as activation energy, magnitude of peak height and peak point temperature on the temperature dependent characteristics.

An attempt has been made to summarize the research and development on the topic of assessing the status of composite Insulators used for outdoor power delivery. Advances made in the evaluation of the electrical performance are discussed. The findings are applicable to other composite insultaing systems, as well. Aspects that have been understood well enough to be of practical use, and those needing further research are outlined.

Many factors influence SF6 insulation and a number of them have been clarified quantitatively. For the next generation of gas-insulated switchgear (GIS), quantitative considerations of these factorsare necessary to enhance reliability and to make GIS more compact. Advanced insulation technology this purpose is described.

Interfacial effect in polymetric composites have been studied extensively. This report deals mainly with the effects of interfacial space charge and interface structure. A model for the dynamic process of interfacial space charge accumulation is proposed. The new model might interpret some interface phenomena which is difficult to be explained in terms of traditional Maxwell-Wagner theory. An interface structure is also presented, by which the importance of surface treatment of glass Fiber for improving the properties of FRP could be well understood.

Electrical breakdown strength of paper-oil and polypropylene/film-oil insulation samples was measured under dc, ac and pulsating voltages. The latter was obtained by superimposing ac upon dc volate and provides an attractive method for a simultaneous testing and assessment of the state of insulation of the various parts of HV apparatus in service. The measurements were carried out over a wide range of the pulsation ratio defined as p=Eac/Edc. The results obtained under pulsating voltages follow colsely an experssion which relates the breakdown strength to the sum of arc tangent and arc cotangent function of the parameter p. The study was carried out using dry paper as well as paper containing various degrees of moisture. The presence of moisture showed a pronounced effect upon the breakdown strength which varied with the pulsation parameter p.

This paper describes a collaborative work between SEI and KEPCO on the Superconducting Magnetic Energy Storage system (SMES). We have studied two types of magnets. One is the 400kJ class LTS-SMES for testing the power stabilization operated at liquid helium temperature (4.2K) and the other is the 100J class HTS-SMES for confirming the possibility of applying HTS wire to SMES at liquid nitrogen temperature (77k). In this paper, the design of the magnet and the test results are described. Each magnet performed completely at rated operation.

In this study, polarization switching characteristics of Pb(ZrxTil-x)O3 (PZT) thin films were investigated. Switching times(ts) were found to be decreased as the Zr mol% was increased. But, the switching peak currents(Imax) showed the largest value at 50 mol% Zr. As a result of this experiment, ts was found to be depended on the remanent polarization and coercive field and also Imax strongly depended on the dielectric constant of PZT thin films. In order to investigate the partial switching kinetics of PZT thin films, short and relatively small voltage pulses were applied to the MFM(metalferroelectric metal) PZT capacitors and polarization switching curves were measured with a variation of the total width of the applied pulses. Also, the switching curves were measured at different applied voltages(4, 8, 10, 12 and 14 volts). As the applied voltages increased, ts and Imax were found to be decreased and increased, respectively. In case of fatigued specimen which we applied $\pm$10 volts square pulse for 1010 cycles, ts and Imax were found to be shorter and smaller than those of virgin specimens. This is due to the decrease of the remanent polarization and the increase of the coercive field.

Paraelectric lead landthanum titanate(PLT) thin films have been prepared by a reactive dc magnetron sputtering system using a multicomponent metal target. The surface area control of each element on the target markedly facilitates the fabrication of thin films of complex ceramic compounds. A postdeposition heat-treatment was applied to all as-deposited PLT thin films at annealing temperatures up to 75$0^{\circ}C$ for crystalization. The composition of the PLT(28) thin filmannealed at $650^{\circ}C$ was: Pb, 0.73; La, 0.28; Ti, 0.88; O, 2.9. The dielectric constant and dissipation factor of the thin film(200 nm) at low filed measurements (500 Vcm-1) are 1216 and 0.018, respectively. The charge storage density using a typical Sawyer-Tower circuit with a 500 Hz sine wave was 12.5 $\mu$Ccm-2 at the electric field of 200 kVcm-1.

Deposition conditions, surface morphology, and electrical properties of polyamic acid alkylamine salts (PAAS) Langmuir-Blodgett(LB) films have been investigated through a study of surface pressure-area $\pi$-A isotherms, AFM (atomic force microscopy), and current-voltage characteristics. To obtain the optimum conditions of film deposition, the $\pi$-A isotherms were examined by varying temperature, barrier moving speed, dipping speed, spreading amount of solution etc. The Z-type LB films were made at the surface pressure of 5 mN m-1 and 25 mN m-1 for the AFM study; the former surface pressure forms the gas phase and the latter one forms the solid phase. The LB film made in the gas phase show domains with a size of about 200 A diameter and 70 A height. However, the LB films made in the solid phase show a very smooth surface with 2 A surface roughness. In the current-voltage characteristics measured along the perpendicular direction of the films, ohmic conduction has been observed below 105 V cm-1 and the calculated electrical conductivity is about 10-13 S cm-1. Nonohmic conduction has been observed above = 10-11 V cm and the conduction mechanism can be explained by the Schottky effect.

Plasma polymerized hexamethyldisiloxane (PPHMDSO) thin films were produced using an electrode capacitively coupled apparatus. Fourier transform infrared spectroscopy analysis indicated that the thin film spectra are composed not only of the corresponding monomer bands but also of several new bands. Auger electron spectroscopy analysis indicated that the permeation depth of aluminum into the films is ca. 30nm when top electrode is deposited by evaporation aluminum. The increase of relative dielectric constant and decrease of dielectric loss tangent with the discharge power is originated from high cross-link of the films.

The effects of Al micro-bumps on the magnetic properties of CoCr(Pt)Ta/Cr films deposited on glass substrates were investigated. The coercivity increased and the coercivity squareness decreased by incorporating Cr/Al underlayers. The cause of the coercivity increase is attributed to the reduction of Co(0002) texture, the increase of magnetic isolation of CoCr(Pt)/Ta grains, and the refinement of CoCr(Pt)/Ta grains deposited on Cr/Al underlayers. The effects of an Al overlayer on the magnetic properties of CoCr(Pt)Ta/Cr films were also studied. The decrease of coercivity squareness is ascribed to the magnetic isolation of CoCr(Pt)Ta grains.

Metallo-phthalocyanines(MPcs) are very sensitive to toxic molecules such as electron affinitive NO2 gas and also chemically and thermally stable since losts of MPcs have been studied for the potential chemcial gas sensors for $NO_2$ using their electrical conductivity. In this study, thin films of octa-dodecyloxy copper -phthalocyanine were prepared by Langmuir-Blodgett(LB) method and characterized by using UV/Vis absorption spectroscopy, and ellipsometry. It was found that the proper transfer surface pressure for the film deposition was 25mN/m and the limiting area per molecule was $112\AA$/molecule. The film thickness of one layer was $64\AA$. Current-voltage(I-V) characteristics of these films were investigated as a function of film thickness.

Suitable replacement materials for ultrathin SiO2 in deeply scaled MOSFETs such as lattice polarizable films, which have much higherpermittivities than SiO2, have bandgaps of only 3.0 to 4.0 eV. Due to these small bandgaps, the reliability of these films as a gate insulator is a serious concern. Ramped voltage, time dependent dielectric breakdown, and hot carrier effect measurements were done on 190 layers of TiO2 which were deposited through the metal-organic chemical vapor deposition of titanium tetrakis-isopropoxide (TTIP). Measurements of the high and low frequency capacitance indicate that virtually no interface state are created during constant current injection stress. The increase in leakage upon electrical stress suggests that uncharged, near-interface states may be created in the TiO2 film near the SiO2 interfacial layer that allow a tunneling current component at low bias.

Along with fusion energy, photovoltaic solar energy conversion has long been considered as one of the few sustainable options for large scale energy supply in the future. In the past, commercial use has been restricted largely to remote area applications where conventional electricity is expensive. However, 1998 marked a year of transition where the major application of the cells changed to become generation of residential electricity in urban areas already supplied by the conventional grid. The current state of the technology is discussed as are major overseas programs to accelerate the urban residential use of photovoltaics, particularly in Japan, Europe and the United States, includng the "million roof" program in the latter. Finally, the planned use of photovoltaics in the Sydney 2000 Olympics is described, where the technology will be used to provide most of the electricity requirements of the 665 residences which will be a legacy of the Olympic Village.