The purpose of this research is to characterize formaldehyde as trace toxic air pollutant in the underground spaces in Gyungnam province. Air samples of formaldehyde were taken in the three underground spaces for ten months from April 2003 to January 2004. The IAQ(Indoor Air Quality) of underground spaces were controled using central ventilation(supply/exhaust) system. The levels of GM of airborne formaldehyde concentrations in three sampling spaces were well below applicable standards, Korean Ministry of Environment, 0.1 ppm. However, some sample of airborne formaldehyde concentrations in underground spaces 'B' and 'C' were in excess of standard, due to the commercial products in shop, structural material, and the climate having high humidity and temperature. There are statistical differences in levels of formaldehyde by sampling spaces (p=0.086).

The photocatalytic oxidation of Rhodamine B(RhB) was studied using photocatalytic reactor filled with module of quartz tube. Module of quartz tube consisted of small quartz tube (inner diameter, 1.5 mm; outer diameter, 3 mm) bundle coated with powder $TiO_2$ and uncoated large quartz tube (inner diameter, 20 mm; outer diameter, 22 mm). Two 30 W germicidal lamp was used as the light source and the reactor volume was 0.5 l. The effects of parameters such as the coating materials and numbers, initial concentration, $H_{2}O_2$ dose and metal deposition (Ag, Pt and Fe) and simultaneous application of $H_{2}O_2$ and metal deposition. The results showed that the initial reaction constant of quartz module coated with powder $TiO_2$ was higher 1.4 time than that of the $TiO_2$ sol and optimum coating number is twice. In order to increase reaction rate, simultaneous application of photocatalytic and photo-fenton reaction using Fe coating and dose $H_{2}O_2$ dose increased reaction rate largely.

Food waste is becoming by environmental problem nowdays increasing festinately in Korea during past 10 years. Food waste collected from garbage trucks that is offered in S municipal government that food waste mixs enough, and sewage sludge collected in the country. Composting experiment conditions achieved in the mixture ratio rate that food waste and sewage sludge are each 10:90, 30:70, 50:50, 60:40, 70:30 and 90:10 $wt\%$. The fermentation temperature was $18{\sim}22^{\circ}C$ at the beginning, and then it was sharply increased to $44{\sim}66^{\circ}C$ up to 1 day after fermentation, which was maintained for more than 3 days. Then, it was slowly decreased to $18{\sim}25^{\circ}C$ up to 8 days after fermentation, which was maintained all the time. It could be known from examiation of various conditions, including reaction rate, salinity. carbon/nitrogen(C/N) ratio, temperature, organic substance, etc.. Optimum mixture ratio rate of composting using food waste and sewage sludge was 60:40 $wt\%$.

Dual actions are the most recently used delivery system in drug study. Dual-action agents are unique chemical entities comprised of two different type of antibacterial compounds covalently linked together in a single molecule in such a way that both components are able to exert their bactericidal properties. Crosslinked sulfadiazine-sulfanilamide such as antibiotics is synthesized by synthetic handle with glutaraldehyde. As a result, New synthetic antibacterial agent exhibited the broad antibacterial activities against Gram(+) and Gram(-) of 4 strains and a long durability supposing that the stomach and blood.

This study was carried to investigate the emission characteristics of mercury from domestic and industrial MSW (municipal solid waste) incinerator stacks. The mercury concentration levels of flue gas from 32 MSW incinerators stacks selected were above the criteria level ($5{\mu}g/S\;m^3$). MSWI facilities exceeding the criteria levels in Korea are due to the poor units comparison of combustion chamber(CC)-cyclone(CY)-stack. So, the mercury from MSW incinerators stack were suspected to contaminate the natural system unless the MSW incinerators were properly controlled. Mean-while, the relationship between mercury concentration and temperature of flue gas in MSW incinerator stacks were examined at two temperature ranges (Group A : $29.85{\sim}327.63^{\circ}C$, Group B : $446.9{\sim}848.15^{\circ}C$). The mercury concentration in flue gas with high temperature range was higher than that of flue gas with low temperature rage. This mean that the temperature of flue gas plays an important role in mercury control in MSW incinerator. The emission characteristics oi mercury was also evaluated by using the correlation matrix between the mercury and NOx, $PM_{10}$, moisture (MO.) at both low temperature and high temperature flue gas ranges. The mercury concentration was mainly affected by NOx, $PM_{10}$. moisture (MO.) at low temperature range, while the mercury concentration at high temperature flue gas was mainly affected by NOx, moisture (MO.). From these results, it was suggested that the temperature of cooling system and the air pollution control device should be properly regulated in order to control mercury of flue gas in MSWI incinerator.

Seaweed waste(SWW) was used to improve the liner effect in recycling of dredged soil as the landfill liner. It was found that the compressive strength became somewhat lower when SWW was added than that was when Ordinary Port-land Cement(OPC) only was added. The permeability coefficient, however, became lower in this case which showed the lowest permeability coefficient when the addition of SWW was one percent. Hence, to comply with the regulations for the compression strength and permeability coefficient of landfill liner, the addition of OPC should be over eight percent and that of seaweed waste one percent. The results of leaching test showed that the solidified material was not against the laws of waste control, so it is possible to use as the landfill liner and to expect sufficient economic effects because wastes such as dredged soil and seaweed can be recycled.

In this study, lots of methods have been studing to utilize energy and decrease contaminated effluents. There has been great progress on IGCC (Integrated gasification combined cycle) to reduce thermal energy losses. The following results have been conducted from desulfurization experiments using waste shell to remove $H_{2}S$. Unreacted core model ior desulfuriration rate prediction of sorbent was indicated. These were linear relationship between time and conversion. So co-current diffusion resistance was conducted reaction rate controlling step. The sulfidation rate is likely to be controlled primarily by countercurrent diffusion through the product layer of calcium sulfide(CaS) formed. Maximum desulfurization capacity was observed at 0.631 mm for lime, oyster and hard-shelled mussel. The kinetics of the sorption of $H_{2}S$ by CaO is sensitive to the reaction temperature and particle size at $800^{\circ}C$, and the reaction rate of oyster was faster than the calcined limestone at $700^{\circ}C$.

I performed the research about the drinking water treatment by precoat filtration and activated carbon adsorption process in the D water treatment plant at Gwangju. D water treatment plant inlet water is supplied from Juam lake in Jeollanamdo. The results are as follows; 1. Element disk used in this experiment are R(pore size $10{\mu}m$), B(pore size $20{\mu}m$). And diatomaceous earth are A(cake pore size $3.5{\mu}m$), B(cake pore size $7{\mu}m$) and C(cake pore size $17{\mu}m$) 2. Filtrate of precoat filter during 30 min are B-C 10.2 > BB 5.7 > R-A 5.4 ($m^3/m^2$). 3. The water quality through B-C+AC and R-A+AC are DOC 1.76 mg/1, 1.288 m/l respectively. 4. total THMs produced by chlorination are $84.2{\mu}g/l$(B-C+AC), $66.11{\mu}g/l$ (R-A+AC), $97{\mu}g/l$ (rapid sand filtration water) respectively. 5. The R-A+AC and B-C+AC process can be substitute of CWTS.

The objective of this investigation was to evaluate applicability of precoat filtration that can be substituted for rapid sand filter of conventional water treatment system(CWTS). Precoat filter used in this experiment are candle filter. Element disk of candle are pore size $10{\mu}m(R),\;20{\mu}m(B)$ And diatomaceous earth are cake pore size $3.5{\mu}m$(Standard Super- Cel; A), $7{\mu}m$(Hyflo Super-Cel; B) and $17{\mu}m$(Celite 545RV; C). $2kg/m^2$ diatomaceous earth is used for precoating, it coated candle in $5{\sim}6mm$ thickness. 1. Al adsorption dosages by diatomaceous earth used in experimental we Hyflo Super-Cel 0.843mg/g, Standard Super-Cel 0.782 mg/g and Celite 545RV 0.766 mg/g. 2. Filtrate of precoat filter during 60min are R-C combination 20.7($m^3/m^2$)>B-C 18.3($m^3/m^2$)>B-B 15.0($m^3/m^2$)> R-B 12.9($m^3/m^2$)> R-A 11,093($l/m^2$). 3. Water quality of precoat filter effluent are thus. $KMnO_4$ consumption are $1.10{\sim}2.20mg/l$, removal rate are $30.9{\sim}65.6\%$. They are R-A 1.10(mg/l)(removal rate $65.6\%$). R-C(2.20 mg/l)(removal rate $30.9\%$). 4. $Al^{3+}$ are not detected with all combination, removal rate $100\%$. 5. Considering water quality and flux, continued running time of R-A combination is 7 hr. Accumulated filtrate are $74.4 m^3/m^2$, average flux is $177.2 l/m^2{\cdot}min$. And filtrate per diatomaceous earth 1g are 37.2 l. 6. R-A effluent's water quality are $KMnO_4$ Consumption 1.10(mg/l), DOC 1.161 mg/1, Al 0.0 mg/1, $UV_{254}$ 0.016/cm, Turbidity 0.1(NTU). R-A combination is suitable to precoat filtration for the settling basin effluent treatment.

We investigate changing characteristics and concentration distribution of ambient air quality using data from which obtained local ambient air monitoring network and local meterological measuring sites in Gwangju area from January to December in 2003. Sulfur dioxide ($SO_2$) showed that increase from 8 AM and decrease in 6 PM but, it was not drastically changed concentration. it also 0.010 ppm in 1995 from at this time it's decrease step by step and than some constant in year 2001 to 2003. Nitrogen dioxide ($NO_2$) concentration was showed highest peak in 10 AM and increase again at 6 PM. And also it showed peak concentration (0.026 ppm) in 2001 and decreased from after that times. Ozone was showed peak concentration in 1 PM and Nitrogen dioxide was ditto in 10 AM from this data, we can conclude that this two article ws showed chemical reaction by 3 to 5 hours. There was no case of Ozone alarm in Gwangju area since 1995, but it showed highest ozone concentration (over 0.070 ppm) in May and June of the year and 2 to 4 PM of the day and sometimes it showed increase at the dawn. Ozone product optimum condition was that air temperature is over $25^{\circ}C$, no rain and increase solar radiation (over $20MJ/m^2$) and no wind or below 2.0 m/s wind speed.

The calcination characteristics of the waste Corbicula Japonica and Ostrea virginjca shell were examined for the future use as desulfurization sorbent. The weight variation was measured according to thermal-decomposition using TGA and observed variation of the phase. The qualitative and quantitative analysis of the sample were performed using XRD and the structural analysis, SEM. The results of TGA and XRD experiments showed that the almost all of the raw samples Corbicula Japonica and Ostrea virginjca were changed from calcite to lime by firing and calcination reaction. The result of SEM experiment showed that the plate type of the raw sample was changed to circle type, so the surface area ratio was increased. Above results suggested that waste Corbicula Japonica and Ostrea virginjca were usable in the viewpoint of the reuse of resource and the decrease of environmental pollution.

Korean certification regulation for particulate filtering respirators requires inward leakage (IL) test as European Standards (EN) and the standard levels of regulation are the same as those of EN. This study was conducted to evaluate particulate filtering respirators being commercially used in the market by using IL and assess the characteristics of IL. The study began with discussing the concept of IL, comparison of IL with fit test, and IL measurement method. Three brands of half masks and 10 brands of filtering facepieces (two top class, four 1st class and four 2nd class), total 13 brands respirators, and 10 test panels (subjects) who were classified in 9 facial grids in accordance with face length and lip length, were selected for IL test. IL tests were conducted in the laboratory of 3M Innovation Center which was established by EN standard. As expected ILs of half masks were lower than those of filtering facepiece mask. ILs of half masks and some filtering facepieces were significantly different in manufacturers. ILs of 1st class filtering facepieces were found to be much more than those of 2nd class and thus the result would cause wearers to get confused to select a mask. Four of six brands being no compliance with standards were thought that they should be tested again for certification because of a lot of differences from standards. There were no significant differences among ILs of five exercises. In 6 out of 13 brands lognormal distribution of ILs may be a better fit distribution and in 7 brands both lognormal and normal distributions were rejected. The result indicates that geometric mean may be better than arithmetic mean to establish standard.

Airborne bacteria, gram negative bacteria (GNB) and fungi were measured in 70 class of 17 kindergartens. The objective of this study is to identify the factors influencing airborne concentrations of bacteria, GNB and fungi using multiple regression analysis. The average concentrations of bacteria and fungi exceeded $1,000\;CFU/m^3$. The average of GNB was $3.7{\times}10^2\;CFU/m^3$. This results indicated that air of kindergartens was contaminated with microbes such as bacteria and fungi. ANOVA test found that the concentrations of bacteria, GNB and fungi were significantly different by the characteristics of weather (rain, after rain, sunny) sampling date (July, August, September and October), the location of sampling site (ground level and basement) and the location of toilet (inside class, nearby class and away class). Multiple regression tests concluded that sampling date, the scale of city where kindergartens are located, the location of sampling site and ventilation efficiency can significantly affect the airborne concentration of bacteria, GNB and fungi. Most of these factors could be related moisture. Environmental factors that can cause the increment of moisture should be controlled in order to reduce airborne concentration of bacteria, GNB and fungi. Legal actions concerning prohibition on the presence of toilet inside class and ventilation criteria should be taken.

This study is to calculate Allocation of Pollution Discharges by administrative region for the TMDL (Total Maximum Daily Load) on Tamjin River. TMDL has the water quality target and value ($BOD_5$, 1 ppm) and is calculated by the QUAL2E model. The expected TMDL for Tamjin River is 1,532,360 kg/day. The calculation showed that the main pollutants are due to the non-point sources in Tamjin River and the aqua-farms are another important sources near the bay. And sources from population and livestock should be reduced, especially aqua-farm source should be managed and eliminated first which is over 14,000 ton/day.

The purpose of this paper is to understand the time series and origin of a chemical component and to compare the difference during yellow sand episodes for analysis $PM_{10}$ chemical components in the region of west in Korean Peninsula, 1999-2001. An annual mean concentration of $PM_{10}$ is $29.1\;{\mu}g/m^3$. A monthly mean and standard deviation of $PM_{10}$ concentration are very high in spring but there is no remarkably seasonal variation. Also, water soluble ionic component of $PM_{10}$ be influenced by double more total anion than total cation, be included $NO_{3}^-\;and\;SO_{4}^{2-}$ for the source of acidity and $NH_{4}^+$ to neutralize. Tracer metals of $PM_{10}$ slowly increases caused by emitted for soil and ocean (Fe, Al, Ca, Mg, Na) and Zn, Pb, Cu, Mn for anthropogenic source. According to method of enrichment factor (E.F) and statistics, assuming that the origin of metal component in $PM_{10}$ most of element in the Earth's crust e.g. Mg, Ca, Fe originates soil and Cu, Zn, Cd, Pb derives from anthropogenic sources. The ionic component for $Na^{+}\;Cl^-,\;Mg^{2+}\;and\;Ca^{2+}$ and Mg, Al, Ca, Fe originated by soil component largely increase during yellow sand period and then tracer metal component as Pb, Cd, Zn decrease. According to factor analysis, the first group is ionic component ($Na^+,\;Mg^{2+},\;Ca^{2+}$) and metal component (Na, Fe, Mn and Ni) be influenced by soil. The second group, Mg, Cr also be influenced by soil particle.

The radon concentrations were measured to survey distribution of radon concentrations in Seoul subway stations. The radon concentrations in air and water were measured at seventeen subway stations(Mapo, Chungjongno, Sodaemun, Kwanghwamun, Chongno3ga, Ulchiro4ga, Tangdaemun, Sangildong on Line 5;Nowon, Chunggye, Hagye, Kongnung, Taenung, Mokkol, Chunghwa, Sangbong, Myomok on Line 7) using the $RAdtrak^{TM}$ radon gas detector, Pylon AB-5 continuous passive radon detector and liquid scintillation counting method from January to May 1999. The major results obtained from this study were as follows: The long-term mean concentrations of radon were $61.8\;Bq/m^3$ in office, $78.9\;Bq/m^3$ in platform, $38.2\;Bq/m^3$ in concourse and $20.1\;Bq/m^3$ in outdoor, respectively. These levels were less than the action level ($148\;Bq/m^3$) of the U.S. EPA. The highest level of short-term mean concentrations was $116.55\;Bq/m^3$ at Chongno3ga station on the 5th line subway stations, while the lowest mean concentration was $19.55\;Bq/m^3$ at Mokkol station on the 7th line subway stations. The highest concentration of radon in the road water and storing underground water in the subway stations was $234.7\;KBq/m^3\;and\;155.5\;KBq/m^3$ in Sodaemun subway station, respectively. The results suggest that radon concentration in subway stations seems to be affected by ventilation and radon concentratin in underground water in the subway stations.

Vehicle occupant exposure to air pollutants has been a subject of concern in recent years because of higher levels of air pollutants inside gasoline or diesel-using vehicle, comparing to the surrounding atmosphere. Contrary to previous studies, fuel of vehicles operated in this study was liquefied petroleum gas (LPG). This study examined the potential exposure and removal efficiency of selected volatile organic compounds (VOCs), nitrogen dioxide ($NO_2$) and respirable suspended particle (RSP) by commercial air cleaning device inside vehicle under different ventilation conditions. Vehicle concentrations inside of benzene, toluene, m,p-xylene, $NO_2$ and RSP were lower under the low ventilation condition. This was indicated that outdoor air pollutants could affect the vehicle air quality inside in case metropolitan cities such as Daegu. The urban vehicle concentrations inside of benzene, toluene, m,p-xylene, $NO_2$ and RSP with air cleaning device were higher than those without air cleaning device. This means that the use of air cleaning device equipped with activated carbon filter, which was used in this study, in the interior of vehicles could be expected to reduce the vehicle occupants exposure to air pollutants effectively. In batch type reactor of laboratory scale, removal efficiencies of air cleaning device used were $97.0\%,\;95.7\%,\;94.6\%\;and\;85.5\%$ respectively in benzene, toluene, m,p-xylene and $NO_2$.

Building materials are composed of very complex chemical compounds, and these indoor building materials discharge very much Volatile Organic Compounds(VOCs). We performed the environmental chamber test to investigate the Total VOCs(TVOCs) emission characteristics and emission factors about chemical and natural coating materials. As the result, we concluded that TVOCs emission are high at initial time and decreased in course of time. Natural paint was low emission level for TVOCs than chemical paint by small chamber test. The TVOCs emission factor-time profile showed a good fit with the results from the measured and predicted value.