The effects of the fiber direction, specimen size and temperature on the compressive strength of carbon fiber reinforced silicon carbide composite (C/SiC composite) manufactured by liquid silicon infiltration(LSI) is investigated. Tests were conducted in accordance with ASTM C 695 at room temperature and elevated temperatures. Experiments are conducted with two different specimens considering grain direction. With grain (W/G) specimens have a carbon fibers parallel to the load direction, but across grain (A/G) specimens have a perpendicular carbon fibers. To verify the specimen size effect of C/SiC composite, two types of specimens are manufactured. One has a one to two ratio of diameter to height and the other has a one to one ratio. The compressive strength of C/SiC composite increased as temperature rise. As specimens are larger, compressive strength of A/G specimens increased, however compressive strength of W/G decreased.

The friction factors according to the flow regimes in helical coil tubes depend on the coil diameter, the tube diameter, and the coil pitch. In previous studies, correlations for the laminar flow regime in helical coil tubes have been proposed. However, studies on the transition flow regime and the turbulent flow regime are insufficient and further researches are necessary. In this study, characteristics of the friction factors for the laminar, transition and turbulent flow regimes in helical coil tubes were experimentally investigated. The helical coil tubes used in the experiments were made of copper. The curvature ratios of the helical coil tubes, which means the ratio of helical coil diameter to inner diameter of the helical coil tube are 24.5 and 90.9. Experiments were carried out in the range of $529{\leq}Re{\leq}39,406$ to observe the flows from the laminar to the turbulent regime. The friction factors were obtained by measuring the differential pressures according to the flow rates in the helical coil tubes while varying the curvature ratios of the helical coil tubes. Experimental data show that the friction factors for the helical coil tube with 24.5 in the curvature ratio of the helical coil tube were larger than those in the straight tube in all flow regimes. As the curvature ratio of the helical coil tube increases, the friction factor in turbulent flow regime tends to be equal to that of the straight tube. In addition, it was confirmed that the transition flow regimes in the helical coil tubes were much wider than those in the straight tube, also the critical Reynolds numbers were larger than those in the straight tube. The results obtained in this experimental study can be used as basic data for studies on the water hammer phenomenon in helical coil tubes.

Cause analysis of accidents associated with industrial machines and devices is essential to improve the effectiveness and the efficiency of industrial safety system in Korea. This study focuses on cause analysis of accidents associated with industrial machines and devices. In particular, analysis of abstracts of accidents which are written in descriptive format and, therefore, inherently unstructured and exhibits characteristics of big data is suggested and tested. Automatic analysis of such big data performed in this study reveals the consistent results with the manual analysis results in previous studies. Analysis results also suggest that incorporating transition from the current user-oriented indirect regulations to more manufacturer and user balanced direct regulations will guarantee more effective prevention of industrial accidents at the early stage of generation of danger.

Many electronic devices are powered by various rechargeable batteries such as lithium-ion recently, and occasionally the batteries undergo thermal runaway and cause fire, explosion, and other hazards. If a battery fire should occur in an electronic device of vehicle and aircraft cabin, it is important to quickly extinguish the fire and cool the batteries to minimize safety risks. Attempts to minimize these risks have been carried out by many researchers but the results have been still unsatisfied. Because most rechargeable batteries are operated on the ion state during charge and discharge of electricity and the combustion of ion state has big difference with normal combustion. Here we focused on the effect of ions including an electron during combustion process. The effects of an ionized fuel on the flame stability and the combustion products were experimentally investigated in the propane jet diffusion flames. The burner used in this experiment consisted of 7.5 mm diameter tube for fuel and the propane was ionized with th ionizer (SUNJE, SPN-11). The results show that toe overall flame stability and shape such as flame length has no significant difference even in the higher ion concentration. However the fuel ionization affects to the pollutant emissions such as NOx and soot. NOx and CO emissions measured in post flame region decreased by fuel ionization, especially high fuel velocity, i.e. high ion density. TGA analysis and morphology of soot by TEM indicates that the fuel ionization makes soot to be matured.

The purpose of this study is to fabricate a sensor module to detect the resistive leakage current (Igr) in real time that occurs to low voltage electric lines and to verify its reliability. In the case of the developed sensor module, wires are inserted into the zero current transformer (ZCT) and current transformer (CT) in advance and then the branch line is connected to the circuit breaker. The measurement result of the resistance of the distribution panel equipped with the developed sensor module shows that the resistance is $0.151m{\Omega}$ between the R and R phases, $0.169m{\Omega}$ between the S and S phases, and $0.178m{\Omega}$ between the T and T phases, respectively. The insulation resistance measured at AC 500 V and 1,000 V is $0.08m{\Omega}$ between the R, S, T and N phases, respectively. Then, the insulation resistance measured at DC 500 V is $83.3G{\Omega}$ between the R, S, T and G terminal, respectively. In addition, the applied withstanding voltage is AC 220 V/380 V/440 V and it was found that characteristics between all phases are good. This study measured the standby power by installing the developed sensor module at the rear of the MCCB and switching the circuit breaker on sequentially. The standby power is 1.350 W when one circuit breaker is turned on, 1.690 W when 2 circuit breakers are turned on, and 4.371 W when 10 circuit breakers are turned on. This study also verified the reliability of the standby power of the distribution panel equipped with the developed sensor module using the Minitab Program (Minitab PGM). Since the analysis shows the statistical average of 1.34627 in the reliable range of normal distribution, standard deviation of 0.001874, AD of 0.554, and P value of 0.140, it is found that the distribution panel equipped with the developed sensor module has high reliability.

This research aimed to develop an leakage detector of analyzing the electric potential generated from the electric leakage of electric equipment of the fountain. To accomplish this goal, the potential gradient was analyzed against path 1 ~ path 4; this was done by taking the lighting of a fountain as the electric leakage point based on code analyses in Korea and other countries. Lighting 1 was taken as the electric leakage point, and the earthing point was set against lightings(2~3). It appeared that the allowable touch voltage against the 1 type(under 2.5 V) exceeded 60.0%. Therefore, the lighting of fountain turned out to be the most dangerous point, and electric shock could be formed by the electric leakage of electric equipment in underwater as well as by the lighting. An leakage detector was developed based on this risk; this detector is capable of analyzing the electric potential of a electric equipments of the fountain in underwater. Then, a verification test was carried out. This leakage detector can be used to measure electric potential in various submerged areas such as swimming pools, flooded spaces, and fountains.

Experiments were carried out the phenomenal observation on effect of corona treated hotmelt laminating film in process of manufacture by 2 kinds of rolling speed and electric power variatons. Surface treatment by corona which is exposure of film surface to electron of ion bombardment, rather than mere exposure to active species, like atomic oxygen or ozone, can enhance adhesion by removing contaminant, electret, roughening surface, and introducing reactive chemical group. Reactive neutrals, ions, electron and photons generated during the corona treatment interact simultaneously with polymers to alter surface chemical composition, wettability, and thus film adhesion. However, it is highly recommended that extensive chains scission is avoided because it can lead to side-effect by forming sticky matter, resulting in dropouts. This paper reviews principles of surface preparation of polypropylene substrate by corona discharging. In addition, the experimental section provides a description of parameter optimization on corona discharging treatment and its side-effect. Experimental results are discussed in terms of surface wetting as determined by contact angle and SEM measurements. When the rolling speed of the film decreased from 1.666 [m / sec] to 0.083 [m / sec], contact angle decreased from $80[^{\circ}]$ to $64[^{\circ}]$, and the wettability was greatly improved. As the supply power increased from 0.4 [kVA] to 2 [kVA] at the corona discharge surface treatment, the contact angle decreased from $77[^{\circ}]$ to $65[^{\circ}]$, and the wettability was greatly improved.

This study compares the interrelation of fit factor(FF) and visual acuity test by the order of wearing preference between Particulate filtering face piece respirators(PFFR) and glasses for 54 participants. Glasses fitting factors is Optical Center Height(OH), Vertex Distance(VD) and Pantoscopic Angle(PA) or Visual acuity. We measured those factors and expressed by the ratio of standard point and change point. Quantitative fit factor was measured by Portacount Pro+ 8038 and compared the result of preference of wearing order between respirators and glasses. Also, we selected to 6 exercises among 8 exercises OSHA QNFT (Quantitative Fit testing) protocol to measure the fit factors. The pass/ fail criterion of FF was set at 100. Visual acuity test chart is developed by Chunsuk Han was used, Descriptive statistics was performed. Descriptive statistics(SAS ver 9.2), it is used geometric means, Wilcoxon analysis, peason correlation(P=0.05) Fit factor was increased when the respirator was worn before wearing the glasses(p=0.000) and decreased for visual acuity(p=0.000) The negative correlation was showed between OH and Overall fit factor(r=-0.409, p=0.002). Among 54 participants, 11 participants(20.3%) were worn respirator before wearing glasses and 1 participant(1.9%) was worn glasses before wearing respirator. The overall fit test showed the higher level was investigated for the group of participants wearing respirator before wearing glasses in 6 exercises. Also, overall fit factor were increased when participants wore glasses prior to respirator(16.6) to respirator prior to glasses(36.6). Visual acuity were increased when participants wore respirator prior to glasses(93.8) to glasses prior to respirator(106.0). Finally, comparison result of overall fit factor and visual acuity were glasses first choice from mask first choice. The results showed that higher overall fit factor was investigate when the participants wore the respirator prior to glassess at all. The results implied that it is important to maintain the overall fit factor and visual acuity according to the consideration of OH for glasses fitting when worker wore respirator and glasses at the same time.

In this study, we developed a system for information sharing and cooperation support system among the accident response organizations to enable prompt and efficient response in responding to chemical accidents. In other words, by applying mobile messenger function, it is proposed to improve the chemical accident response system that provides information necessary for accident response promptly and accurately, and facilitates bi-directional communication between accident response organizations and field responders, thereby enabling efficient and organic response. As a result of comparing the information provision time before and after the chemical accident of chemical accident response information sharing system, the ratio of processing of substance information and chemical air diffusion information within 30 minutes was improved by 8% and 32%, respectively. As a result of this study, applying the chemical accident response information sharing system to the chemical accident response is expected to contribute to the improvement of the system and the ability to cope with the accident more effectively.

The rapid progress toward the 4th industrial society has led to possibilities of fire increase. It is pointed out that, though initial fire suppression is emphasized, the current legal systems do not sufficiently recognize the importance of initial fire suppression. In order to resolve this, problems of the current legal systems and regulations, as well as fire-fighting facilities to be equipped according to the size of specific fire-fighting objects, were diagnosed. Also, suggestions for improvement were provided through comparative analysis with relevant laws and technical regulations of Korea and other countries. According to fire safety standards such as NFPA, IMO, ISO, and Russian standards, automatic fire extinguishers are to be installed as per the adaptability criteria of fire extinguishers and automatic fire extinguishers. In Korea, the "Act on Fire Prevention and Installation, Maintenance, and Safety Control of Fire-fighting Systems" cover the types and scope of fire fighting facilities that include specific fire protection objects, such as electric room, power room, and substation room. This study has identified that, in case of a place with a floor area of less than $300m^2$, the installation requirement is not clearly specified. Therefore, in this study, fire extinguishing equipment and automatic fire extinguishing equipment to be added for each sub-use application are proved to have fire extinguishing performance of Class A, Class B, and Class C, respectively. In view of the fact that, in overseas standards, all space except containing such materials as Deep fire, metal fire and peroxide, can be installed with fire fighting equipment, a legal system for specifying the capacity units of fire fighting apparatus by application is, in this study, proposed.

This study analyses the types, related operations, facilities, and causes of chemical accidents in Korea based on the RISCAD classification taxonomy. In addition, human error analysis was carried out employing different human error classification criteria. Explosion and fire were major accident types, and nearly half of the accidents occurred during maintenance operation. In terms of related facility, storage devices and separators were the two most frequently involved ones. Results of the human error-based analysis showed that latent human errors in management level are involved in many accidents as well as active errors in the field level. Action errors related to unsafe behavior leads to accidents more often compared with the checking behavior. In particular, actions missed and inappropriate actions were major problems among the unsafe behaviors, which implicates that the compliance with the work procedure should be emphasized through education/training for the workers and the establishment of safety culture. According to the analysis of the causes of the human error, the frequency of skill-based mistakes leading to accidents were significantly lower than that of rule-based and knowledge based mistakes. However, there was limitation in the analysis of the root causes due to limited information in the accident investigation report. To solve this, it is suggested to adopt advanced accident investigation system including the establishment of independent organization and improvement in regulation.

According to the statistics publication of KOSHA, more than half of serious accidents at the construction sites were related to the temporary works and/or the temporary structures such as scaffoldings, shores, earth retaining walls, etc. The structural failures are occurred because of the overload acting on the structures or lack of performance of the one or more members of the structures. For the prevention of the collapse accidents relating to the temporary structures at the construction sites, we have to control construction processes not to occur the overload and also to control the performance and quality of each member of the temporary structures. MOLIT has amended the "Construction Technology Promotion Act" on Jan. 7th, 2015 to ensure the structural safety of the temporary structures. According to the Act, the designers of the construction design projects should check the structural integrity of the structures including the temporary structures and the construction companies have to let 'the Relative Professionals' confirm the structural integrity of temporary structures, the shores(${\geq}5m$ high) and the scaffolds(${\geq}31m$ high), before construction. Also, MOLIT has amended the "Regulation for Construction Technology Promotion Act" on Jul. 4th, 2016 for quality management and testing of temporary equipments. According th this regulation, the construction companies and supervisors should manage and test the temporary equipments before using them. In this paper, the standard drawings of the shores(< 5 m high) and the scaffolds(< 31 m high) and the amended "Business Guideline for Quality Management of Construction Work" are presented. As the result of this study, MOLIT noticed the amended "Business Guideline for Quality Management of Construction Work" on Jul. 1st, 2017.

The seismic response, the natural frequencies and the mode shapes of an offshore wind turbine with twisted tripod substructure subject to various pile-ground interactions are discussed in this paper. The acceleration responses of the tower head by four historical earthquakes are presented as the seismic response, while the other loads are assumed as ambient loads. For the pile-ground interactions, the fixed, linear and nonlinear models are employed to simulate the interactions and the p-y, t-z and Q-z curves are utilized for the linear and nonlinear models. The curves are designed for stiff, medium and soft clays, and thus, the seven types of the pile-ground interactions are used to compare the seismic response, the acceleration of the tower head. The mode shapes are similar to each other for all types of pile-ground interactions. The natural frequencies, however, are almost same for the three clay types of the linear model, while the natural frequency of the fixed support model is quite different from that of the linear interaction model. The wind turbine with the fixed support model has the biggest magnitude of acceleration. In addition, the nonlinear model is more sensitive to the stiffness of clay than the linear pile-ground interaction model.

The improvement of safety and health education method in construction site was investigated through the survey for workers and delphi technique. The results of preliminary survey done for workers were analyzed using the multi variance analyses, and the questionnaires for delphi survey were composed based on the results of preliminary survey. Finally, the participatory safety and health education method was suggested. The result showed that most of workers were very interested in accident prevention and health. On the contrary, they did not actively participate in safety activities in sites including safety and health education. In order to improve workers' levels of safety consciousness and prevent the construction accident, the participatory safety and health education method that construction workers directly examine and give presentations about accident causes and measures was suggested and verified by tests. One-way instructor-led safety and health education used widely and participatory safety and health education with workers were carried out by dividing participants into two groups. After education, the examination is done for two groups. The test results found that the average score of safety consciousness of the worker group that received participatory safety education was higher than that of the work group that received instructor-led safety education. And the Delphi technique utilizing experts was analyzed that participatory safety education has a great effect on improvement of workers' level of safety consciousness.

This study investigated the improvement of safety certification marking method and location marked on temporary equipments in order to guarantee the quality and safety of temporary equipments. The survey was performed for the stakeholder (manufacturers, lessors, and users) to find out the effective way that all stakeholder can agree each other. The main reason which users checked the safety certification making is that the mandatory safety certification marking can prevent the usage of poor and illegal temporary equipments. For the marking method, all stakeholder agreed that a depressed engraving method was an effective and usable displaying method. The opinions about the position of safety certification marking among the users, lessors, and manufacturers did not come into the agreement. The manufacturers preferred the marking position in which the engraving process is easy, but users wanted the conspicuous place such as vertical member. However, it is necessary to continuously study ways to adopt the position preferred by the users.

Since tower cranes are susceptible to wind loads, the operation of the tower crane should be ceased when it exposed to a strong wind. For this reason, even in Korea, the operation limit for wind loading on the tower crane is regulated by a law. Recently the Korean law in which provided the wind speed limit to cease the tower crane operation has been revised from "instantaneous wind speed of 20 m/s" to "instantaneous wind speed of 15 m/s". Although this revision is expected to reduce safety risks in tower crane operation, some field operators still insist to lower the wind speed limit. However, in many countries "wind speed of 20 m/s" is normally used as the maximum in-service wind speed for tower cranes. Therefore, the investigation of the proper wind speed for regulation would be helpful to secure the safety of the tower crane operation under windy condition. In this study the validity of the revised wind speed limit is investigated with the surveys targeted to both tower crane practitioners and parties of concerned in construction companies, in which various questions was provided for a suitable wind speed limit and the answers were analyzed. The results showed that the revised wind speed limit is acceptable to tower crane practitioners as well as the parties of concerned in construction companies and is satisfying the structural stability requirement for in-service state tower crane. Therefore, it can be concluded that the revised wind speed limit is valid in humanly safety point of view.

This study examined the effect of Behavior Based Safety(BBS) program on safe behaviors of bus drivers and passengers. Four male bus drivers working at a H transportation company situated in Seoul participated in this study. BBS program consisted of education, prompts, and self-monitoring with goal setting. Dependent variables were the percentage of two safe driving behaviors of bus drivers (departure after stopping for 3 seconds, announcement for holding bus handles) and the percentage of one safe behavior of passengers getting on the busses those drivers drove (holding bus handles). A primary observer and two trained assistant observers measured two safe behaviors of the bus drivers with behavior checklists by riding on the busses and the passengers' safe behavior was observed by CCTV installed on each bus. An ABC multiple baseline design across participants was adopted. After baseline(A), education and prompts(B) and self-monitoring with goal setting(C) were introduced sequentially to each participant. The results showed that BBS program was effective to increase both bus drivers' and passengers' safe behaviors. Especially self-monitoring with goal setting was more effective in improving safe behaviors of bus drivers than education/prompts. These results suggest that education/prompts and self-monitoring with goal setting would be an alternative treatment technique to improve safety for lone workers such as bus drivers.

The study aims present data collection on the current state of safety and safety consciousness in universities' laboratories to verify the relation between investigation factors and further draw implications. The first finding is that laboratories with high risk level do not have better safety management performance than those with lower risk level. Secondly, labs that experienced accidents has a higher level of control than those without any. Regarding to the university's acceptance of safety requirements, the group with a high level of risk awareness or accidents were concerned that their universities did not provide sufficient support in safety management. It means that safety is low on the list of priorities in Universities' overall agenda and individual labs are responsible of their own safety. Most of the causes of accidents in the labs are man-made than physical errors. It requires that continuous safety educations and measures through safe research activities are means to eliminate and reduce the individual's safety frigidity. Through the survey, it is known that current education's system and contents are too generalized to reflect the characteristics of each laboratory. Thus, it is difficult to recognize various risk situations and to actually prevent safety accidents. Therefore, it is necessary to shift to customized curriculum and system for various major fields.

With the increase in frequency of typhoons and heavy rains following the climate change, the scale of damage from the calamities in the mountainous areas has been growing larger and larger, which is different from the past. For the case of Korea where 64% of land is consisted of the mountainous areas, establishment of the check dams has been drastically increased after 2000 in order to reduce the damages from the debris flow. However, due to the lack of data on scale, location and kind of check dams established for reducing the damages in debris flow, the measures to prevent damages based on experience and subjective basis have to be relied on. Under this study, the high-precision DEM data was structured by using the terrestrial LiDAR in the Jecheon area where the debris flow damage occurred in July 2009. And, from the numerical models of the debris flow, Kanako-2D that is available to reflect the erosion and deposition action was applied to install the erosion control facilities (water channel, check dam) and analyzed the effect of reducing the debris flow shown in the downstream.After installing the erosion control facilities, most of debris flow moves along the water channel to reduce the area to expand the debris flow, and after installing the check dam, the flow depth and flux of the debris flow were reduced along with the erosion. However, as a result of analyzing the diffusion area, flow depth, erosion and deposition volume of the debris flow generated from the deposition part after modifying the location of the check dams with the damages occurring on private residences and agricultural land located on the upstream area, the highest reduction effect was shown when the check dam is installed in the maximal discharge points.

Rotary that causes traffic delays and safety issues by high-speed entry vehicles is currently being improved to roundabout. The operational difference between rotary and roundabout can cause driver's confusion and traffic accident. The purpose of this study is to develop the accident rate models which explain the factors related to the accidents by land use and intersection type. The main results are as follows. First, the null hypotheses that the type of land use and two intersections do not affect the accident rate are rejected. Second, the conflicting factors such as the number of crosswalk and bicycle lane should be carefully considered to reduce traffic accident at rotary. In the case of roundabout, greater than 3.5 m in circulatory lane width and two circulatory lane are analyzed to be important to prevent the accidents. Finally, the commercial and mixed areas are evaluated to be weak to traffic accidents than residential area.

This study aims to analyze and discuss the accidents based on the level of traffic culture (LOT). In pursuing the above, LOT are divided into three categories based on the standardized index of traffic culture. Also, this study focuses on developing the accident models using GLM (generalized linear model). The main results are as follows. First, the null hypotheses that the ratios of fatal and serious injured persons (FSI) are the same over categories are rejected. Second, as the common variables, the ratio of turn signal usage and elderly population are analysed to be impacted to the ratio of FSI. Third, the traffic culture indicators among 5 accident factors which give impact to 'high level' are judged to affect the reduction of FSI. Fourth, compared to other levels, the traffic law violations among 7 accident factors of 'medium level' are estimated to influence the increase of FSI. Finally, in 'low level', the increasing ratio of traffic culture index compared to that of previous year and the number of hospital beds per person are evaluated to be significant to reducing the ratio of FSI. This study can be expected to give some policy implications to regional traffic safety policy-making.

A traffic fatality by young people marked average annual decrease of 4.5% since 2011. Meanwhile, a traffic fatality by senior over 65 years old marked average annual increase of 7.9% for the last five years which means that the annual increase of traffic fatality by senior will be a serious problem. This study started questioning that senior drivers over 65 years old did not retain the same causal factor of fatal traffic accidents and thus extensively analyzed a risk of it by age group quantitatively, dividing the senior driver group into the early, middle and latter stages. Depending on the aging level, the risk of traffic fatality showed a wide difference in seven different types of traffic accidents generally, and happened to increase with latter and middle parts of the senior driver more than the early part. Therefore, this study proposes four policy suggestions: 1) The senior driver need to be offered customized driving educations and the improvement of road environment is also recommended. 2) Political assistance is needed to support and guide a safety related technology installation for the new or existing car. 3) Renewal of driving license and an aptitude test(physical examination, cognitive test) for drivers over 75 years old should take in a less than 3 years and an additional road test is needed as occasion demands. 4) Like the United States and Europe, development and extension of customized treatment guidebook for medical teams who examine senior drivers is needed and establishment of education and administration system that a supervisor of driving license renewal can impose safety restriction and American anonymity reporting system is considered to institutionalize in the medium to longer term.