This paper deals with the result of an analysis on the effect of the power generation by municipal solid waste(MSW)-refuse derived fuel(RDF) and the introduction of tipping fee sharing between RDF manufacturing and power generation project. As a model case for the MSW generated at small and medium cities in our country, an analysis of the RDF power generation and Tipping fee sharing shows that 1) MSW amount of 7,800* $10^3 $t/y could produce 1,950*$10^3$t/y of RDF 2) Electric power generated by MSW-RDF could supply 290,000 households/year and 98,548 C-t/y of $CO_2$ could be reduced. 3) Tipping Fee should be shared by the considering of the contents of project of both side between RDF Production and power generation.

In offset or intaglio printing machine, it's operated with combination of blanket cylinder and impression cylinder. The blanket cylinder has some number of grooves to attach the blanket on surface. In case of operating the printing machine, it has generate mechanical impact noise when the two cylinders encounter with the grooves. So, in this study, we developed a printing pressure control algorithm with hydraulic servo control system. We also proposed simulation model of experimental device to analysis the throw on force response of hydraulic servo actuator. Finally, we have reduced the mechanical impact noise and improved printing quality with a groove detecting signal and PI control of hydraulic servo actuator.

Up to now, collimators have teen generally produced by handwork and only a few companies have produced by semi-automatic system. Under this situation, automatic system for assembly of optical collimators has risen as a mast essential technique in the development of optical communication components. In this study, it was constructed to develop optical collimators with high functionality and we manufactured optical collimators with a GRIN rod lens and spherical lens using automatic system. Therefore, we worked a performance test through a comparison of collimators made by automatic system and handwork with angle augment, bean size. Also we selected a optimum assembly condition of GRIN rod lens and spherical lens. As a result, it brought a reduction of the tact time and an improvement of an efficiency and a productivity of optical collimators, therefore it was found that automatic system was indispensable for materialization of optical collimators with high functionality.

This study was performed to develop accelerated life test method of machanical parts using cumulative damage theory that used to model the fatigue of parts that receive variable load. The cumulative damage theory was introduced, and the estimation of life and calculation of accelerated life test time was illustrated. As the actual application example, accelerated life test method of agricultural tractor transmission was described. Life distribution of agricultural tractor transmission was supposed to follow Weibull distribution and life test time was calculated under the conditions of average life (MTBF) 3,000 hours and 90% reliability for one test sample. According to the cumulative damage theory, because test time can shorten in case increase test load, test time could be reduced by 482 hours when we put the load 1.1 times of rated load than 0.73 times of rated load that is equivalent load calculated by load spectrum of the agricultural tractor. This time, acceleration coefficient was 11.7. This accelerated test method was used to develop accelerated test method of gear reducer, hydraulic hose and bearing as well as agricultural tractor transmission and it is considered to be applied comprehensively to machanical parts the fatigue of which is happened by load or pressure etc.

Hydraulic breaker attached excavator generally used for the destroying and disassembling of buildings, crashing road pavement, breaking rocks at quarry and etc. The developed breaker are determined their own destructive force and number of impact by the input hydraulic flow rate and pressure than the operating conditions, In this study, the characteristics of pressure variation in closed vessel is invested for testing the impact energy of hydraulic breaker. To test the impact energy, the test system is designed as a mechanism consisted with a hydraulic cylinder, main base, pressure sensor, LVDT, data acquisition system and etc.. The developed test system is applied to measure the impact energy for hydraulic breaker. The proposed testing method could be applied for conventional impact test and the control system evaluation for hydraulic breakers.

Performance demonstration with real flawed specimens has been strongly required for nondestructive evaluation of safety class components in nuclear power plant. Specimen has been designed to produce mechanical fatigue flaw with tension stress and fatigue flaw has been produced to control stress and cycle, for suitable roughness. Notch condition is considered for control of fracture mode. After seal welding for fracture surface, final welding was performed to complete flaw specimen with GTAW(Gas Tungsten Arc welding) and FCAW(Flux Cored Arc Welding). It was demonstrated flaw size of flawed specimen by radiographic. testing and ultrasonic testing.

The intensity of x-ray or gamma-ray is attenuated according to density and thickness of the transmitted medium. In this study, by using this principle, on-line real-time radiometric system was developed using a 128 channels linear array of solid state detectors to measure wall thickness of insulated piping system. This system uses a Ir-192 as a gamma ray source and detector is composed of BGO scintillator and photodiode. Ir-192 gamma ray source and linear detector array mounted on a computer controlled robotic crawler. The Ir-192 gamma ray source is located on one side of the piping components and the detector array on the other side. The individual detectors of the detector array measure the intensity of the gamma rays after passing through the walls and the insulation of the piping component under measurement. The output of the detector array is amplified by amplifier and transmitted to the computer. This system collects and analyses the data from the detector array in real-time. The maximum measurable length of pipe is 120cm/mm. in the case of 1mm scanning interval.

A martensitic precipitation hardening stainless steel, 17-4PH has been widely used in the aircraft, chemical and nuclear industries for long time, owing to the excellent mechanical properties with corrosion resistance that can be achieved by simple heat treatment. The microstructure and mechanical properties of the 17-4PH stainless steel cast parts for aircraft, such as impeller, are largely affected by heat treatment condition. But the database of heat treatment has not been clearly established in the domestic investment casting industries because the domestic aerospace, industry lags behind the advanced countries. In this study, the microstructural evolution and mechanical properties of cast 17-4PH stainless steel depending on the heat treatment conditions and aging at $400^{\circ}C$ were investigated.

Even in the world wide automobile companies where a few simple modules are put into practical use, the front subframe modules of which performances of durability, NVH and crash are significantly important are under planing. In this study, design technology for the automobile front subframe module, which consists of an engine, a transmission and steering parts, structural components (frame, upper arm, lower arm and brake etc.) and rubber components(engine mount, axle mount and rubber disc etc.), was developed. A FEM-based analytical approach was used to evaluate the multiaxial high cycle fatigue damage of the front subframe module. Strain-life fatigue database system and expert system for fatigue properties of welded materials were developed. Stiffness values of the various rubber bushes mounted on the front subframe were evaluated by experimental method and FEM. TWB(Tailor Welded Blank) technology was applied to forming the cross member of the front subframe. Performance evaluations in relation to NVH and crash were conducted by using CAE technologies.

An Internet-based dynamic analysis system, called P-DYN, for multibody dynamic systems is developed. All the interfaces of the system are accessible via Web browsers, such as Netscape or Explorer. The system uses a template type P-DYN/Modeler as a preprocessor. The P-DYN postprocessor composed of P-DYN/Plotter and P-DYN/Animator is developed in JAVA. The P-DYN/Solver for predicting the dynamic behavior is run on the server. Anyone who wants to analyze the dynamics of multibody systems or share results data can access the analysis system over the Internet regardless of their OS, platform, or location.

In this study, the crashworthiness of KHST has been evaluated by analysing a nonlinear spring/bar-damper-mass model of 1-dimensional collision dynamics. The numerical results show that KHST can easily absorb kinetic energy at lower impact force and acceleration in heavy collisions, when compared with KTX. Also, in a Light collision like a traint-to-train accident at lower speed under 8 kph, the carbody and components of KHST can be protected without any damage except the energy absorbing tube to be replaced easily. However, KTX may be much damaged in the light collision because there is no energy absorbing tube. In conclusion, the crashworthy performance of KHST has been much improved than that of KTX, although there are something to be improved for a better crashworthy performance

In this paper, the design of a decatizing cylinder with uniformly distributed pressure in a decatizing system is investigated by using the Finite Element Method. Particularly, since deflection of a cylinder will not perform to iron the fabrics, the cylinder design insuring uniform pressure is very important. In this paper proposed two improved cylinder model obtained by changing the support type of the bean and the support location. And perform optimization with two improved cylinder model.