Advances in concrete construction

  • 제11권6호
  • /
  • Pages.531-544
  • /
  • 2021
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Effect of mixing Nano-silica and Perlite with pervious concrete for nitrate removal from the contaminated water

  • Hosseini, Seyed Azim (Department of Civil Engineering, South Tehran Branch, Islamic Azad University) ;
  • Toghroli, Ali (Department of Civil Engineering, South Tehran Branch, Islamic Azad University)
  • 투고 : 2020.07.26
  • 심사 : 2021.05.11
  • 발행 : 2021.06.25
⟨ 이전 논문 다음 논문 ⟩

초록

Nitrogen and phosphorus contained in storm water runoff contaminate both surface and ground waters, causing problems for natural aquatic systems and human health. Pervious concrete particularly developed for pollutant removal might be a novel notion to remove nitrate from runoff. In this research, three aggregates were used in pervious concrete as Nano silica, perlite (Pe) and zeolite (Z) which are able to adsorb pollutants. The water absorption, compressive strength, porosity, permeability of aggregate and nitrate removal of concrete samples were evaluated in tests. While adding Nano silica, perlite and zeolite, experiments have shown that addition of fine grains enhances runoff efficiency and compressive strength, but reduces permeability and porosity. Both adsorbents improved the runoff quality while increasing the additives' ratio. The mechanical properties were density of 879 (Kg/m3), permeability of 1.06 (cm/s), the void rate of 19.7(%), compressive strength of 3.6 (MPa), and nitrate removal of about 75%. While adding perlite with the highest (40%) water absorption, the results showed no reactivity of aggregates in terms of alkali-silica reaction. Considering the Permeability tests, perlite has the minimum (1.4 cm/s) permeability, and then adding perlite to previous concrete brought the nitrate absorption capacity about 70 ml/g (60%). The best results belonged to samples containing zeolite treatments (with 15% adsorbent and 0, 10, 20% fine-grains) with a maximum pollution decline and improved Chemical Oxygen Demand (COD) (87.1, 82.6 and 89.3%), Biochemical oxygen demand (BOD) (88.1, 87.3 and 90.7%) and Total suspended solids (TSS) (75.8, 79.1 and 84.6%). Thus, zeolite has shown effective mechanical characteristics and runoff quality, while perlite and Nano silica has shown a poor and moderate performance among the adsorbents in all tests, respectively.

키워드

참고문헌

  1. Abedini, M. and Zhang, C. (2021), "Dynamic performance of concrete columns retrofitted with FRP using segment pressure technique", Compos. Struct., 260, 113473. https://doi.org/10.1016/j.compstruct.2020.113473.
  2. Abedini, M., Zhang, C., Mehrmashhadi, J. and Akhlaghi, E. (2020), "Comparison of ALE, LBE and pressure time history methods to evaluate extreme loading effects in RC column", Struct., 28, 456-466. https://doi.org/10.1016/j.istruc.2020.08.084.
  3. Abedini, M. and Zhang, C. (2021), "Dynamic vulnerability assessment and damage prediction of RC columns subjected to severe impulsive loading", Struct. Eng. Mech., 77(4), 441-461. https://doi.org/10.12989/sem.2021.77.4.441.
  4. Afshar, A., Jahandari, S., Rasekh, H., Shariati, M., Afshar, A. and Shokrgozar, A. (2020), "Corrosion resistance evaluation of rebars with various primers and coatings in concrete modified with different additives", Constr. Build. Mater., 262, 120034. https://doi.org/10.1016/j.conbuildmat.2020.120034.
  5. Aggregate, Concrete (2004), State of the Practice National Review, Washington, DC.
  6. Alam, Z., Sun, L., Zhang, C., Su, Z. and Samali, B. (2021), "Experimental and numerical investigation on the complex behaviour of the localised seismic response in a multi-storey plan-asymmetric structure", Struct. Infrastr. Eng., 17(1), 86-102. https://doi.org/10.1080/15732479.2020.1730914
  7. Alam, Z., Zhang, C. and Samali, B. (2020), "Influence of seismic incident angle on response uncertainty and structural performance of tall asymmetric structure", Struct. Des. Tall Spec. Build., 29(12), e1750. https://doi.org/10.1002/tal.1750.
  8. Alam, Z., Zhang, C. and Samali, B. (2020), "The role of viscoelastic damping on retrofitting seismic performance of asymmetric reinforced concrete structures", Earthq. Eng. Eng. Vib., 19(1), 223-237. https://doi.org/10.1007/s11803-020-0558-x
  9. Ali, T., Meldi, S., Zainah, I., Maryam, S., Mahdi, S. and Shahaboddin, S. (2018), "RETRACTED ARTICLE: Potential of soft computing approach for evaluating the factors affecting the capacity of steel-concrete composite beam", J. Intel. Manuf., 29(8), 1793-1801. https://doi.org/10.1007/s10845-016-1217-y.
  10. Arabnejad Khanouki, M.M., Ramli Sulong, N.H. and Shariati, M. (2011), "Behavior of through beam connections composed of CFSST columns and steel beams by finite element studying", Adv. Mater. Res., 168, 2329-2333. https://doi.org/10.4028/www.scientific.net/AMR.168-170.2329.
  11. Bai, Y., Wang, S., Mou, B., Wang, Y. and Skalomenos, K. A. (2021), "Bi-directional seismic behavior of steel beam-column connections with outer annular stiffener", Eng. Struct., 227, 111443. https://doi.org/10.1016/j.engstruct.2020.111443.
  12. Chen, C., Shi, L., Shariati, M., Toghroli, A., Mohamad, E.T., Bui, D. T. and Khorami, M. (2019), "Behavior of steel storage pallet racking connection-A review", Steel Compos. Struct., 30(5), 457-469. https://doi.org/10.12989/scs.2019.30.5.457.
  13. Chen, F., Jin, Z., Wang, E., Wang, L., Jiang, Y., Guo, P., ... & He, X. (2021), "Relationship model between surface strain of concrete and expansion force of reinforcement rust", Scientif. Report., 11(1), 1-11. https://doi.org/10.1038/s41598-021-83376-w.
  14. Chen, F., Zhong, Y., Gao, X., Jin, Z., Wang, E., Zhu, F., ... & He, X. "Non-uniform model of relationship between surface strain and rust expansion force of reinforced concrete".
  15. Chen, S., Hassanzadeh-Aghdam, M.K. and Ansari, R. (2018), "An analytical model for elastic modulus calculation of SiC whiskerreinforced hybrid metal matrix nanocomposite containing SiC nanoparticles", J. Alloy. Compound., 767, 632-641. https://doi.org/10.1016/j.jallcom.2018.07.102.
  16. Cosic, K., Korat, L., Ducman, V. and Netinger, I. (2015), "Influence of aggregate type and size on properties of pervious concrete", Constr. Build. Mater., 78, 69-76. https://doi.org/10.1016/j.conbuildmat.2014.12.073.
  17. Daie, M., Jalali, A., Suhatril, M., Shariati, M., Khanouki, M.A., Shariati, A. and Kazemi-Arbat, P. (2011), "A new finite element investigation on pre-bent steel strips as damper for vibration control", Int. J. Phys. Sci., 6(36), 8044-50. https://doi.org/10.5897/ijps11.1585.
  18. Davoodnabi, S.M., Mirhosseini, S.M. and Shariati, M. (2019), "Behavior of steel-concrete composite beam using angle shear connectors at fire condition", Steel Compos. Struct., 30(2), 141-147. https://doi.org/10.12989/scs.2019.30.2.141.
  19. Duan, Y., Liu, Y., Chen, Z., Liu, D., Yu, E., Zhang, X., ... & Du, H. (2020), "Amorphous molybdenum sulfide nanocatalysts simultaneously realizing efficient upgrading of residue and synergistic synthesis of 2D MoS 2 nanosheets/carbon hierarchical structures", Green Chem., 22(1), 44-53. https://doi.org/10.1039/c9gc02855b
  20. Foroughi, M., Khiadani, M., Amin, M.M., Pourzamani, H.R. and Vahid Dastjerdi, M. (2013), "Treatment of synthetic urban runoff using manganese oxide-coated sand in the presence of magnetic field", https://doi.org/10.4103/2277-9183.115794.
  21. Hamidian, M., Shariati, M., Arabnejad, M.M.K. and Sinaei, H. (2011), "Assessment of high strength and light weight aggregate concrete properties using ultrasonic pulse velocity technique", Int. J. Phys. Sci., 6(22), 5261-5266.
  22. Heydari, A. and Shariati, M. (2018), "Buckling analysis of tapered BDFGM nano-beam under variable axial compression resting on elastic medium", Struct. Eng. Mech., 66(6), 737-748. https://doi.org/10.12989/sem.2018.66.6.737.
  23. Hosseinpour, E., Baharom, S., Badaruzzaman, W.H.W., Shariati, M. and Jalali, A. (2018), "Direct shear behavior of concrete filled hollow steel tube shear connector for slim-floor steel beams", Steel Compos. Struct., 26(4), 485-499. https://doi.org/10.12989/scs.2018.26.4.485.
  24. HS, N.K., Kattimani, S. and Nguyen-Thoi, T. (2021), "Influence of porosity distribution on nonlinear free vibration and transient responses of porous functionally graded skew plates", Defence Technology. https://doi.org/10.1016/j.dt.2021.02.003.
  25. Huang, H., Huang, M., Zhang, W., Pospisil, S. and Wu, T. (2020), "Experimental investigation on rehabilitation of corroded RC columns with bsp and hpfl under combined loadings", J. Struct. Eng., 146(8), 04020157. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002725
  26. Ichlas, Z.T. and Ibana, D.C. (2017), "Process development for the direct solvent extraction of nickel and cobalt from nitrate solution: aluminum, cobalt, and nickel separation using Cyanex 272", Int. J. Min. Metal. Mater., 24(1), 37-46. https://doi.org/10.1007/s12613-017-1376-7
  27. Jalali, A., Daie, M., Nazhadan, S.V.M., Kazemi-Arbat, P. and Shariati, M. (2012), "Seismic performance of structures with pre-bent strips as a damper", Int. J. Phys. Sci., 7(26), 4061-4072. https://doi.org/10.5897/IJPS11.1324.
  28. Jena, S.K., Sahu, J., Padhy, G., Mohanty, S. and Dash, A. (2020), "Chlorination roasting-coupled water leaching process for potash recovery from waste mica scrap using dry marble sludge powder and sodium chloride", Int. J. Min. Metal. Mater., 27(9), 1203-1215. https://doi.org/10.1007/s12613-020-1994-3.
  29. Jiang, Q., Shao, F., Lin, W., Gu, K., Jiang, G. and Sun, H. (2017), "Optimizing multistage discriminative dictionaries for blind image quality assessment", IEEE Tran. Multimedia, 20(8), 2035-2048. https://doi.org/10.1109/TMM.2017.2763321.
  30. Ju, Y., Shen, T. and Wang, D. (2020), "Bonding behavior between reactive powder concrete and normal strength concrete", Constr. Build. Mater., 242, 118024. https://doi.org/10.1016/j.conbuildmat.2020.118024.
  31. Kaplan, G., Gulcan, A., Cagdas, B. and Bayraktar, O.Y. (2021), "The impact of recycled coarse aggregates obtained from waste concretes on lightweight pervious concrete properties", Envir. Sci. Pollut. Res., 28(14), 17369-17394. https://doi.org/10.1007/s11356-020-11881-y.
  32. Katebi, J., Shoaei-parchin, M., Shariati, M., Trung, N.T. and Khorami, M. (2019), "Developed comparative analysis of metaheuristic optimization algorithms for optimal active control of structures", Eng. Comput., 1-20. https://doi.org/10.1007/s00366-019-00780-7.
  33. Ke, P.C., Liu, Z.H. and Li, L. (2018), "Synthesis, characterization, and property test of crystalline polyferric sulfate adsorbent used in treatment of contaminated water with a high As (III) content", Int. J. Miner. Metal. Mater., 25(10), 1217-1225. https://doi.org/10.1007/s12613-018-1674-8.
  34. Kevern, J.T., Wang, K. and Schaefer, V.R. (2010), "Effect of coarse aggregate on the freeze-thaw durability of pervious concrete", J. Mater. Civil Eng., 22(5), 469-475. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000049.
  35. Khorami, M., Alvansazyazdi, M., Shariati, M., Zandi, Y., Jalali, A. and Tahir, M. (2017), "Seismic performance evaluation of buckling restrained braced frames (BRBF) using incremental nonlinear dynamic analysis method (IDA)", Earthq. Struct., 13(6), 531-538. http://doi.org/10.12989/eas.2017.13.6.531.
  36. Khorami, M., Khorami, M., Motahar, H., Alvansazyazdi, M., Shariati, M., Jalali, A. and Tahir, M.M. (2017), "Evaluation of the seismic performance of special moment frames using incremental nonlinear dynamic analysis", Struct. Eng. Mech., 63(2), 259-268. https://doi.org/10.12989/sem.2017.63.2.259.
  37. Khorramian, K., Maleki, S., Shariati, M., Jalali, A. and Tahir, M.M. (2017), "Numerical analysis of tilted angle shear connectors in steel-concrete composite systems", Steel Compos. Struct., 23(1), 67-85. https://doi.org/10.12989/scs.2017.23.1.067.
  38. Khorramian, K., Maleki, S., Shariati, M. and Ramli Sulong, N.H. (2015), "Behavior of tilted angle shear connectors", PLoS one, 10(12), e0144288. https://doi.org/10.1371/journal.pone.0144288.
  39. Li, C., Sun, L., Xu, Z., Wu, X., Liang, T. and Shi, W. (2020), "Experimental investigation and error analysis of high precision FBG displacement sensor for structural health monitoring", Int. J. Struct. Stab. Dyn., 20(06), 2040011. https://doi.org/10.1142/S0219455420400118.
  40. Li, D., Toghroli, A., Shariati, M., Sajedi, F., Bui, D.T., Kianmehr, P., ... & Khorami, M. (2019), "Application of polymer, silicafume and crushed rubber in the production of Pervious concrete", Smart Struct. Syst, 23(2), 207-214. https://doi.org/10.12989/sss.2019.23.2.207.
  41. Lian, C. and Zhuge, Y. (2010), "Optimum mix design of enhanced permeable concrete-an experimental investigation", Constr. Build. Mater., 24(12), 2664-2671. https://doi.org/10.1016/j.conbuildmat.2010.04.057.
  42. Luo, Z., Sinaei, H., Ibrahim, Z., Shariati, M., Jumaat, Z., Wakil, K., ... & Khorami, M. (2019), "Computational and experimental analysis of beam to column joints reinforced with CFRP plates", Steel Compos. Struct., 30(3), 271-280. https://doi.org/10.12989/scs.2019.30.3.271.
  43. Mansouri, I., Shariati, M., Safa, M., Ibrahim, Z., Tahir, M.M. and Petkovic, D. (2020), "Analysis of influential factors for predicting the shear strength of a V-shaped angle shear connector in composite beams using an adaptive neuro-fuzzy technique", 30, 1247. https://doi.org/10.1007/s10845-017-1306-6
  44. Mehrabi, P., Shariati, M., Kabirifar, K., Jarrah, M., Rasekh, H., Trung, N.T., ... & Jahandari, S. (2021), "Effect of pumice powder and nano-clay on the strength and permeability of fiberreinforced pervious concrete incorporating recycled concrete aggregate", Constr. Build. Mater., 287, 122652. https://doi.org/10.1016/j.conbuildmat.2021.122652
  45. Mohammadhassani, M., Akib, S., Shariati, M., Suhatril, M. and Khanouki, M.A. (2014), "An experimental study on the failure modes of high strength concrete beams with particular references to variation of the tensile reinforcement ratio", Eng. Fail. Anal., 41, 73-80. https://doi.org/10.1016/j.engfailanal.2013.08.014.
  46. Mohammadhassani, M., Suhatril, M., Shariati, M. and Ghanbari, F. (2013), "Ductility and strength assessment of HSC beams with varying of tensile reinforcement ratios", Struct. Eng. Mech.., 48(6), 833-848. https://doi.org/10.12989/sem.2013.48.6.833.
  47. Mohammadhassani, M., Nezamabadi-Pour, H., Suhatril, M. and Shariati, M. (2013), "Identification of a suitable ANN architecture in predicting strain in tie section of concrete deep beams", Struct. Eng. Mech., 46(6), 853-868. http://doi.org/10.12989/sem.2013.46.6.853.
  48. Mohammadhassani, M., Nezamabadi-Pour, H., Suhatril, M. and Shariati, M. (2014), "An evolutionary fuzzy modelling approach and comparison of different methods for shear strength prediction of high-strength concrete beams without stirrups", Smart Struct. Syst., 14(5), 785-809. http://doi.org/10.12989/.2014.14.5.785.
  49. Montgomery, D.C., Runger, G.C. and Hubele, N.F. (2009), Engineering Statistics, John Wiley & Sons.
  50. Mou, B., Li, X., Bai, Y. and Wang, L. (2019), "Shear behavior of panel zones in steel beam-to-column connections with unequal depth of outer annular stiffener", J. Struct. Eng., 145(2), 04018247. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002256.
  51. Naghipour, M., Niak, K.M., Shariati, M. and Toghroli, A. (2020), "Effect of progressive shear punch of a foundation on a reinforced concrete building behavior", Steel Compos. Struct., 35(2), 279-294. http://doi.org/10.12989/scs.2020.35.2.279.
  52. Naghipour, M., Yousofizinsaz, G. and Shariati, M. (2020), "Experimental study on axial compressive behavior of welded built-up CFT stub columns made by cold-formed sections with different welding lines", Steel Compos. Struct., 34(3), 347. http://doi.org/10.12989/scs.2020.34.3.347.
  53. Nasrollahi, S., Maleki, S., Shariati, M., Marto, A. and Khorami, M. (2018), "Investigation of pipe shear connectors using push out test", Steel Compos. Struct., 27(5), 537-543. http://dx.doi.org/10.12989/scs.2018.27.5.537.
  54. Paknahad, M., Shariati, M., Sedghi, Y., Bazzaz, M. and Khorami, M. (2018), "Shear capacity equation for channel shear connectors in steel-concrete composite beams", Steel Compos. Struct, 28(4), 483-494. https://doi.org/10.12989/scs.2018.28.4.483.
  55. Pitcher, S.K., Slade, R.C.T. and Ward, N.I. (2004), "Heavy metal removal from motorway stormwater using zeolites", Sci. Total Environ., 334, 161-166. https://doi.org/10.1016/j.scitotenv.2004.04.035.
  56. Qi, C., Chen, Q. and Kim, S.S. (2020), "Integrated and intelligent design framework for cemented paste backfill: A combination of robust machine learning modelling and multi-objective optimization", Min. Eng., 155, 106422. https://doi.org/10.1016/j.mineng.2020.106422.
  57. Qi, C. and Fourie, A. (2019), "Cemented paste backfill for mineral tailings management: Review and future perspectives", Min. Eng., 144, 106025. https://doi.org/10.1016/j.mineng.2019.106025.
  58. Radfard, M., Yunesian, M., Nabizadeh, R., Biglari, H., Nazmara, S., Hadi, M., ... & Mahvi, A.H. (2018), "Drinking water quality and arsenic health risk assessment in Sistan and Baluchestan, Southeastern Province, Iran", Human Ecolog. Risk Asses., 25(4), 949-965. https://doi.org/10.1080/10807039.2018.1458210.
  59. Radfard, M., Yunesian, M., Nabizadeh, R., Biglari, H., Nazmara, S., Hadi, M., ... & Mahvi, A.H. (2018), "Drinking water quality and arsenic health risk assessment in Sistan and Baluchestan, Southeastern Province, Iran", Human Ecolog. Risk Asses., 25(4), 949-965. https://doi.org/10.1080/10807039.2018.1458210.
  60. Razavian, L., Naghipour, M., Shariati, M. and Safa, M. (2020), "Experimental study of the behavior of composite timber columns confined with hollow rectangular steel sections under compression", Struct. Eng. Mech., 74(1), 145-156. https://doi.org/10.12989/sem.2020.74.1.145.
  61. Chahnasir, E.S., Zandi, Y., Shariati, M., Dehghani, E., Toghroli, A., Mohamad, E.T., ... & Khorami, M. (2018), "Application of support vector machine with firefly algorithm for investigation of the factors affecting the shear strength of angle shear connectors", Smart Struct. Syst., 22(4), 413-424. https://doi.org/10.12989/sss.2018.22.4.413.
  62. Safa, M., Shariati, M., Ibrahim, Z., Toghroli, A., Baharom, S.B., Nor, N.M. and Petkovic, D. (2016), "Potential of adaptive neuro fuzzy inference system for evaluating the factors affecting steelconcrete composite beam's shear strength", Steel Compos. Struct., 21(3), 679-688. https://doi.org/10.12989/scs.2016.21.3.679.
  63. Safa, M., Maleka, A., Arjomand, M.A., Khorami, M. and Shariati, M. (2019), "Strain rate effects on soil-geosynthetic interaction in fine-grained soil", Geomech. Eng., 19(6), 533-542. https://doi.org/10.12989/gae.2019.19.6.533.
  64. Safa, M., Sari, P.A., Shariati, M., Suhatril, M., Trung, N.T., Wakil, K. and Khorami, M. (2020), "Development of neuro-fuzzy and neuro-bee predictive models for prediction of the safety factor of eco-protection slopes", Physica A: Stat. Mech. Its Appl., 550, 124046. https://doi.org/10.1016/j.physa.2019.124046
  65. Safa, M., Sari, P.A., Shariati, M., Suhatril, M., Trung, N.T., Wakil, K. and Khorami, M. (2020), "Development of neuro-fuzzy and neuro-bee predictive models for prediction of the safety factor of eco-protection slopes", Physica A: Stat. Mech. Its Appl., 550, 124046.. https://doi.org/10.12989/scs.2019.30.5.417.
  66. Sedghi, Y., Zandi, Y., Shariati, M., Ahmadi, E., Azar, V.M., Toghroli, A., ... & Wakil, K. (2018), "Application of ANFIS technique on performance of C and L shaped angle shear connectors", Smart Struct. Syst., 22(3), 335-340. https://doi.org/10.12989/sss.2018.22.3.335.
  67. Shah, S.N.R., Sulong, N.R., Jumaat, M.Z. and Shariati, M. (2016), "State-of-the-art review on the design and performance of steel pallet rack connections", Eng. Fail. Anal., 66, 240-258. https://doi.org/10.1016/j.engfailanal.2016.04.017.
  68. Shah, S.N.R., Sulong, N.R., Khan, R., Jumaat, M.Z. and Shariati, M. (2016), "Behavior of industrial steel rack connections", Mech. Syst. Signal Pr., 70, 725-740. https://doi.org/10.1016/j.ymssp.2015.08.026.
  69. Shahabi, S.E.M., Sulong, N., Shariati, M., Mohammadhassani, M. and Shah, S.N.R. (2016), "Numerical analysis of channel connectors under fire and a comparison of performance with different types of shear connectors subjected to fire", Steel Compos. Struct., 20(3), 651-669. https://doi.org/10.12989/scs.2016.20.3.651.
  70. Shariat, M., Shariati, M., Madadi, A. and Wakil, K. (2018), "Computational Lagrangian Multiplier Method by using for optimization and sensitivity analysis of rectangular reinforced concrete beams", Steel Compos. Struct., 29(2), 243-256. https://doi.org/10.12989/scs.2018.29.2.243.
  71. Shariati, A., Sulong, N.H., Suhatril, M. and Shariati, M. (2012), "Investigation of channel shear connectors for composite concrete and steel T-beam", Int. J. Phys. Sci., 7(11), Articlenumber. 0626DBF16390 1828-1831. https://doi.org/10.5897/IJPS11.1604.
  72. Shariati, A., RamliSulong, N.H. and Shariati, M. (2012), "Various types of shear connectors in composite structure: A review", Int. J. Phys. Sci., 7(22), 2876-2890. https://doi.org/10.5897/IJPSx11.004.
  73. Shariati, A., Shariati, M., Sulong, N.R., Suhatril, M., Khanouki, M.A. and Mahoutian, M. (2014), "Experimental assessment of angle shear connectors under monotonic and fully reversed cyclic loading in high strength concrete", Constr. Build. Mater., 52, 276-283. https://doi.org/10.1016/j.conbuildmat.2013.11.036.
  74. Shariati, M., Ramli Sulong, N.H., Arabnejad, M.M.K.H. and Mahoutian, M. (2011), "Shear resistance of channel shear connectors in plain, reinforced and lightweight concrete", Scientif. Res. Essay., 6(4), 977-983.
  75. Shariati, M., Ramli-Sulong, N.H., Arabnejad, M.M., Shafigh, P. and Sinaei, H. (2011), "Assessing the strength of reinforced concrete structures through Ultrasonic Pulse Velocity and Schmidt Rebound Hammer tests", Scientif. Res. Essay., 6(1), 213-220. https://doi.org/10.5897/SRE10.879.
  76. Shariati, M., Ramli Sulong, N.H., Sinaei, H., Arabnejad Khanouki, M.M. and Shafigh, P. (2011), "Behavior of channel shear connectors in normal and light weight aggregate concrete (experimental and analytical study)", Adv. Mater. Res., 168, 2303-2307. https://doi.org/10.4028/www.scientific.net/AMR.168-170.2303.
  77. Shariati, M. (2013), "Behaviour of C-shaped shear connectors in stell concrete composite beams", Jabatan Kejuruteraan Awam, Fakulti Kejuruteraan, Universiti Malaya.
  78. Shariati, M., Ramli Sulong, N.H. and Arabnejad Khanouki, M.M. (2010), "Experimental and analytical study on channel shear connectors in light weight aggregate concrete", Proceedings of the 4th International Conference on Steel Compos. Struct., 21-23.
  79. Shariati, M., Ramli Sulong, N.H., Arabnejad Khanouki, M.M. and Shariati, A. (2011), "Experimental and numerical investigations of channel shear connectors in high strength concrete", Proceedings of the 2011 World Congress on Advances in Struct. Eng. Mech. (ASEM'11+).
  80. Shariati, M., Sulong, N.R., Shariati, A. and Khanouki, M.A. (2016), "Behavior of V-shaped angle shear connectors: experimental and parametric study", Mater. Struct., 49(9), 3909-3926. https://doi.org/10.1617/s11527-015-0762-8.
  81. Shariati, M., Sulong, N.R., Shariati, A. and Kueh, A.B.H. (2016), "Comparative performance of channel and angle shear connectors in high strength concrete composites: An experimental study", Constr. Build. Mater., 120, 382-392. https://doi.org/10.1016/j.conbuildmat.2016.05.102.
  82. Shariati, M., Sulong, N.R., Suhatril, M., Shariati, A., Khanouki, M.A. and Sinaei, H. (2012), "Behaviour of C-shaped angle shear connectors under monotonic and fully reversed cyclic loading: An experimental study", Mater. Des., 41, 67-73.. https://doi.org/10.1016/j.matdes.2012.04.039.
  83. Shariati, M., Ramli Sulong, N., Suhatril, M., Shariati, A., Arabnejad Khanouki, M. and Sinaei, H. (2012), "Fatigue energy dissipation and failure analysis of channel shear connector embedded in the lightweight aggregate concrete in composite bridge girders", Proceedings of the 5th international conference on Eng. Fail. Anal., ICEFA, 1-4.
  84. Shariati, M., Sulong, N.R., Suhatril, M., Shariati, A., Khanouki, M.A. and Sinaei, H. (2013), "Comparison of behaviour between channel and angle shear connectors under monotonic and fully reversed cyclic loading", Constr. Build. Mater., 38, 582-593. https://doi.org/10.1016/j.conbuildmat.2012.07.050.
  85. Shariati, M., Shariati, A., Sulong, N.R., Suhatril, M. and Khanouki, M. A. (2014), "Fatigue energy dissipation and failure analysis of angle shear connectors embedded in high strength concrete", Eng. Fail. Anal., 41, 124-134. https://doi.org/10.1016/j.engfailanal.2014.02.017.
  86. Shariati, M., Trung, N.T., Wakil, K., Mehrabi, P., Safa, M. and Majid. K.. (2019), "Moment-rotation estimation of steel rack connection using extreme learning machine", Steel Compos. Struct., 31(5), 427-435. https://doi.org/10.12989/scs.2019.31.5.427.
  87. Shariati, M. (2008), "Assessment of building using nonedestructive test techniques (ultra sonic pulse velocity and schmidt rebound hammer)", Universiti Putra Malaysia.
  88. Shariati, M., Armaghani, D.J., Khandelwal, M., Zhou, J. and Khorami, M. (2021), "Assessment of longstanding effects of fly ash and silica fume on the compressive strength of concrete using extreme learning machine and artificial neural network", J. Adv. Eng. Comput., 5(1), 50-74. http://doi.org/10.25073/jaec.202151.308.
  89. Shariati, M., Azar, S.M., Arjomand, M.A., Tehrani, H.S., Daei, M. and Safa, M. (2019), "Comparison of dynamic behavior of shallow foundations based on pile and geosynthetic materials in fine-grained clayey soils", Geomech. Eng., 19(6), 473-484. https://doi.org/10.12989/gae.2019.19.6.473.
  90. Shariati, M., Azar, S.M., Arjomand, M.A., Tehrani, H.S., Daei, M. and Safa, M. (2020), "Evaluating the impacts of using piles and geosynthetics in reducing the settlement of fine-grained soils under static load", Geomech. Eng., 20(2), 87-101. https://doi.org/10.12989/gae.2020.20.2.087.
  91. Shariati, M., Faegh, S.S., Mehrabi, P., Bahavarnia, S., Zandi, Y., Masoom, D.R., ... & Salih, M.N. (2019), "Numerical study on the structural performance of corrugated low yield point steel plate shear walls with circular openings", Steel Compos. Struct., 33(4), 569-581. https://doi.org/10.12989/scs.2019.33.4.569.
  92. Shariati, M., Ghorbani, M., Naghipour, M., Alinejad, N., & Toghroli, A. (2020), "The effect of RBS connection on energy absorption in tall buildings with braced tube frame system", Steel Compos. Struct., 34(3), 393-407. https://doi.org/10.12989/scs.2020.34.3.393.
  93. Shariati, M., Grayeli, M., Shariati, A. and Naghipour, M. (2020), "Performance of composite frame consisting of steel beams and concrete filled tubes under fire loading", Steel Compos. Struct., 36(5), 587-602. https://doi.org/10.12989/scs.2020.36.5.587.
  94. Shariati, M., Heyrati, A., Zandi, Y., Laka, H., Toghroli, A., Kianmehr, P., ... & Poi-Ngian, S. (2019), "Application of waste tire rubber aggregate in porous concrete", Smart Struct. Syst., 24(4), 553-566. https://doi.org/10.12989/sss.2019.24.4.553.
  95. Shariati, M., Mafipour, M.S., Haido, J.H., Yousif, S.T., Toghroli, A., Trung, N.T. and Shariati, A. (2020), "Identification of the most influencing parameters on the properties of corroded concrete beams using an Adaptive Neuro-Fuzzy Inference System (ANFIS)", Steel Compos. Struct., 34(1), 155. http://doi.org/10.12989/scs.2020.34.1.155.
  96. Shariati, M., Mafipour, M.S., Mehrabi, P., Bahadori, A., Zandi, Y., Salih, M.N., ... & Poi-Ngian, S. (2019), "Application of a hybrid artificial neural network-particle swarm optimization (ANN-PSO) model in behavior prediction of channel shear connectors embedded in normal and high-strength concrete", Appl. Sci., 9(24), 5534. https://doi.org/10.3390/app9245534.
  97. Shariati, M., Mafipour, M.S., Mehrabi, P., Shariati, A., Toghroli, A., Trung, N.T. and Salih, M.N. (2020), "A novel approach to predict shear strength of tilted angle connectors using artificial intelligence techniques", Eng. Comput., 1-21. https://doi.org/10.1007/s00366-019-00930-x.
  98. Shariati, M., Mafipour, M.S., Mehrabi, P., Zandi, Y., Dehghani, D., Bahadori, A., ... & Poi-Ngian, S. (2019), "Application of Extreme Learning Machine (ELM) and Genetic Programming (GP) to design steel-concrete composite floor systems at elevated temperatures", Steel Compos. Struct., 33(3), 319-332. https://doi.org/10.12989/scs.2019.33.3.319.
  99. Shariati, M., Naghipour, M., Yousofizinsaz, G., Toghroli, A. and Tabarestani, N.P. (2020), "Numerical study on the axial compressive behavior of built-up CFT columns considering different welding lines", Steel Compos. Struct., 34(3), 377-391. https://doi.org/10.12989/scs.2020.34.3.377.
  100. Shariati, M., Rafie, S., Zandi, Y., Fooladvand, R., Gharehaghaj, B., Mehrabi, P., ... & Poi-Ngian, S. (2019), "Experimental investigation on the effect of cementitious materials on fresh and mechanical properties of self-consolidating concrete", Adv. Concrete Constr., 8(3), 225-237. http://doi.org/10.12989/acc.2019.8.3.225.
  101. Shariati, M., Shariati, A., Trung, N.T., Shoaei, P., Ameri, F., Bahrami, N. and Zamanabadi, S.N. (2021), "Alkali-activated slag (AAS) paste: Correlation between durability and microstructural characteristics", Constr. Build. Mater., 267, 120886. https://doi.org/10.1016/j.conbuildmat.2020.120886.
  102. Shariati, M., Sulong, N.R. and Khanouki, M.A. (2012), "Experimental assessment of channel shear connectors under monotonic and fully reversed cyclic loading in high strength concrete", Mater. Des., 34, 325-331. https://doi.org/10.1016/j.matdes.2011.08.008.
  103. Shariati, M., Tahir, M.M., Wee, T.C., Shah, S.N.R., Jalali, A. and Khorami, M. (2018), "Experimental investigations on monotonic and cyclic behavior of steel pallet rack connections", Eng. Fail. Anal., 85, 149-166. https://doi.org/10.1016/j.engfailanal.2017.08.014.
  104. Shariati, M., Tahmasbi, F., Mehrabi, P., Bahadori, A. and Toghroli, A. (2020), "Monotonic behavior of C and L shaped angle shear connectors within steel-concrete composite beams: an experimental investigation", Steel Compos. Struct., 35(2), 237-247. https://doi.org/10.12989/scs.2020.35.2.237.
  105. Shu, X., Huang, B., Wu, H., Dong, Q. and Burdette, E.G. (2011), "Performance comparison of laboratory and field produced pervious concrete mixtures", Constr. Build. Mater., 25(8), 3187-3192. https://doi.org/10.1016/j.conbuildmat.2011.03.002.
  106. Sinaei, H., Jumaat, M.Z. and Shariati, M. (2011), "Numerical investigation on exterior reinforced concrete Beam-Column joint strengthened by composite fiber reinforced polymer (CFRP)", Int. J. Phys. Sci., 6(28), 6572-6579. https://doi.org/10.5897/IJPS11.1225.
  107. Sinaei, H., Shariati, M., Abna, A.H., Aghaei, M. and Shariati, A. (2012), "Evaluation of reinforced concrete beam behaviour using finite element analysis by ABAQUS", Scientif. Res. Essay., 7(21), 2002-2009. https://doi.org/10.5897/SRE11.1393.
  108. Sonebi, M. and Bassuoni, M.T. (2013), "Investigating the effect of mixture design parameters on pervious concrete by statistical modelling", Constr. Build. Mater., 38, 147-154. https://doi.org/10.1016/j.conbuildmat.2012.07.044.
  109. Sonebi, M. and Bassuoni, M.T. (2013), "Investigating the effect of mixture design parameters on pervious concrete by statistical modelling", Constr. Build. Mater., 38, 147-154. https://doi.org/10.1016/j.conbuildmat.2012.07.044.
  110. Sun, L., Li, C., Zhang, C., Liang, T. and Zhao, Z. (2019), "The strain transfer mechanism of fiber bragg grating sensor for extra large strain monitoring", Sensor., 19(8), 1851. https://doi.org/10.3390/s19081851.
  111. Sun, L., Li, C., Zhang, C., Su, Z. and Chen, C. (2018), "Early monitoring of rebar corrosion evolution based on FBG sensor", Int. J. Struct. Stab. Dyn., 18(08), 1840001. https://doi.org/10.1142/S0219455418400011.
  112. Sun, L., Yang, Z., Jin, Q. and Yan, W. (2020), "Effect of Axial Compression Ratio on Seismic Behavior of GFRP Reinforced Concrete Columns", Int. J. Struct. Stab. Dyn., 20(06), 2040004. https://doi.org/10.1142/S0219455420400040.
  113. Sun, M., Yan, L., Zhang, L., Song, L., Guo, J. and Zhang, H. (2019), "New insights into the rapid formation of initial membrane fouling after in-situ cleaning in a membrane bioreactor", Proc. Biochem., 78, 108-113. https://doi.org/10.1016/j.procbio.2019.01.004.
  114. Tahmasbi, F., Maleki, S., Shariati, M., Ramli Sulong, N.H. and Tahir, M.M. (2016), "Shear capacity of C-shaped and L-shaped angle shear connectors", PLoS one, 11(8), e0156989. https://doi.org/10.1371/journal.pone.0156989.
  115. Tan, K., Qin, Y., Du, T., Li, L., Zhang, L. and Wang, J. (2021), "Biochar from waste biomass as hygroscopic filler for pervious concrete to improve evaporative cooling performance", Constr. Build. Mater., 287, 123078. https://doi.org/10.1016/j.conbuildmat.2021.123078.
  116. Toghroli, A., Mohammadhassani, M., Suhatril, M., Shariati, M. and Ibrahim, Z. (2014), "Prediction of shear capacity of channel shear connectors using the ANFIS model", Steel Compos. Struct., 17(5), 623-639. http://doi.org/10.12989/scs.2014.17.5.623.
  117. Toghroli, A., Shariati, M., Karim, M.R. and Ibrahim, Z. (2017), "Investigation on composite polymer and silica fume-rubber aggregate pervious concrete", Proceedings of the 5th International Conference on Advances in Civil, Structural and Mechanical Engineering-CSM. https://doi.org/10.15224/978-1-63248-132-0-56.
  118. Toghroli, A., Shariati, M., Sajedi, F., Ibrahim, Z., Koting, S., Mohamad, E.T. and Khorami, M. (2018), "A review on pavement porous concrete using recycled waste materials", Smart Struct. Syst., 22(4), 433-440. https://doi.org/10.12989/sss.2018.22.4.433.
  119. Toghroli, A., Mehrabi, P., Shariati, M., Trung, N.T., Jahandari, S. and Rasekh, H. (2020), "Evaluating the use of recycled concrete aggregate and pozzolanic additives in fiber-reinforced pervious concrete with industrial and recycled fibers", Constr. Build. Mater., 252, 118997. https://doi.org/10.1016/j.conbuildmat.2020.118997.
  120. Trung, N.T., Shahgoli, A.F., Zandi, Y., Shariati, M., Wakil, K., Safa, M. and Khorami, M. (2019), "Moment-rotation prediction of precast beam-to-column connections using extreme learning machine", Struct. Eng. Mech., 70(5), 639-647. https://doi.org/10.12989/sem.2019.70.5.639.
  121. Trung, N.T., Alemi, N., Haido, J.H., Shariati, M., Baradaran, S. and Yousif, S.T. (2019), "Reduction of cement consumption by producing smart green concretes with natural zeolites", Smart Struct. Syst., 24(3), 415-425. https://doi.org/10.12989/sss.2019.24.3.415.
  122. Xie, Q., Sinaei, H., Shariati, M., Khorami, M., Mohamad, E.T. and Bui, D.T. (2019), "An experimental study on the effect of CFRP on behavior of reinforce concrete beam column connections", Steel Compos. Struct., 30(5), 433-441. https://doi.org/10.12989/scs.2019.30.5.433.
  123. Xu, J., Li, Y., Ren, C., Wang, S., Vanapalli, S.K. and Chen, G. (2021), "Influence of freeze-thaw cycles on microstructure and hydraulic conductivity of saline intact loess", Cold Reg. Sci. Technol., 181, 103183. https://doi.org/10.1016/j.coldregions.2020.103183.
  124. Yang, S.T., Zhou, M., Jiang, T., Guan, S.F., Zhang, W.J. and Xue, X.X. (2016), "Application of a water cooling treatment and its effect on coal-based reduction of high-chromium vanadium and titanium iron ore", Int. J. Miner. Metal. Mater., 23(12), 1353-1359. https://doi.org/10.1007/s12613-016-1358-1.
  125. Yang, Y., Chen, H., Zou, X., Shi, X.L., Liu, W.D., Feng, L., ... & Chen, Z.G. (2020), "Flexible carbon-fiber/semimetal Bi nanosheet arrays as separable and recyclable plasmonic photocatalysts and photoelectrocatalysts", ACS Appl. Mater. Interf., 12(22), 24845-24854. https://doi.org/10.1021/acsami.0c05695.
  126. Yang, Y., Li, Y., Yao, J., Iglauer, S., Luquot, L., Zhang, K., ... & Wang, Z. (2020), "Dynamic pore-scale dissolution by CO2- saturated brine in carbonates: Impact of homogeneous versus fractured versus vuggy pore structure", Water Resour. Res., 56(4), e2019WR026112. https://doi.org/10.1029/2019WR026112.
  127. Yang, Y., Tao, L., Yang, H., Iglauer, S., Wang, X., Askari, R., ... & Sun, H. (2020), "Stress sensitivity of fractured and vuggy carbonate: an X-Ray computed tomography analysis", J. Geophys. Res.: Solid Earth, 125(3), e2019JB018759. https://doi.org/10.1029/2019JB018759.
  128. Yang, Y., Yao, J., Wang, C., Gao, Y., Zhang, Q., An, S. and Song, W. (2015), "New pore space characterization method of shale matrix formation by considering organic and inorganic pores", J. Nat. Gas Sci. Eng., 27, 496-503. https://doi.org/10.1016/j.jngse.2015.08.017.
  129. Yap, S.P., Chen, P.Z.C., Goh, Y., Ibrahim, H.A., Mo, K.H. and Yuen, C.W. (2018), "Characterization of pervious concrete with blended natural aggregate and recycled concrete aggregates", J. Clean. Prod., 181, 155-165. https://doi.org/10.1016/j.jclepro.2018.01.205.
  130. Yazdani, M., Kabirifar, K., Frimpong, B.E., Shariati, M., Mirmozaffari, M. and Boskabadi, A. (2021), "Improving construction and demolition waste collection service in an urban area using a simheuristic approach: A case study in Sydney, Australia", J. Clean. Prod., 280, 124138. https://doi.org/10.1016/j.jclepro.2020.124138.
  131. Ye, M., Jiang, J., Chen, H.M., Zhou, H.Y. and Song, D.D. (2021), "Seismic behavior of an innovative hybrid beam-column connection for precast concrete structures", Eng. Struct., 227, 111436. https://doi.org/10.1016/j.engstruct.2020.111436.
  132. Zandi, Y., Shariati, M., Marto, A., Wei, X., Karaca, Z., Dao, D. K., ... & Khorami, M. (2018), "Computational investigation of the comparative analysis of cylindrical barns subjected to earthquake", Steel Compos. Struct., 28(4), 439-447. https://doi.org/10.12989/scs.2018.28.4.439.
  133. Zhang, C.W., Ou, J.P. and Zhang, J.Q. (2006), "Parameter optimization and analysis of a vehicle suspension system controlled by magnetorheological fluid dampers", Struct. Control Hlth. Monit., 13(5), 885-896. https://doi.org/10.1002/stc.63.
  134. Zhang, C. (2014), "Control force characteristics of different control strategies for the wind-excited 76-story benchmark building structure", Adv. Struct. Eng., 17(4), 543-559. https://doi.org/10.1260/1369-4332.17.4.543.
  135. Zhang, C., Alam, Z., Sun, L., Su, Z. and Samali, B. (2019), "Fibre Bragg grating sensor-based damage response monitoring of an asymmetric reinforced concrete shear wall structure subjected to progressive seismic loads", Struct. Control Hlth. Monit., 26(3), e2307. https://doi.org/10.1002/stc.2307.
  136. Zhang, C., Gholipour, G. and Mousavi, A.A. (2020), "State-ofthe-art review on responses of RC structures subjected to lateral impact loads", Arch. Comput. Meth. Eng., 1-31. https://doi.org/10.1007/s11831-020-09467-5.
  137. Zhang, C., Li, L. and Ou, J. (2010), "Swinging motion control of suspended structures: Principles and applications", Struct. Control Hlth. Monit., 17(5), 549-562. https://doi.org/10.1002/stc.331.
  138. Zhang, C., Gholipour, G. and Mousavi, A.A. (2020), "Blast loads induced responses of RC structural members: State-of-the-art review", Compos. Part B: Eng., 195, 108066. https://doi.org/10.1016/j.compositesb.2020.108066
  139. Zhang, C. and Ou, J. (2008), "Control structure interaction of electromagnetic mass damper system for structural vibration control", J. Eng. Mech., 134(5), 428-437. https://doi.org/10.1061/(ASCE)0733-9399(2008)134:5(428).
  140. Zhang, C. and Ou, J. (2015), "Modeling and dynamical performance of the electromagnetic mass driver system for structural vibration control", Eng. Struct., 82, 93-103. https://doi.org/10.1016/j.engstruct.2014.10.029.
  141. Zhang, C. and Wang, H. (2019), "Robustness of the active rotary inertia driver system for structural swing vibration control subjected to multi-type hazard excitations", Appl. Sci., 9(20), 4391. https://doi.org/10.3390/app9204391.
  142. Zhang, C. and Wang, H. (2019), "Swing vibration control of suspended structure using active rotary inertia driver system: Parametric analysis and experimental verification", Appl. Sci., 9(15), 3144. https://doi.org/10.3390/app9153144.
  143. Zhang, H., Guan, W., Zhang, L., Guan, X. and Wang, S. (2020), "Degradation of an Organic Dye by Bisulfite Catalytically Activated with Iron Manganese Oxides: The Role of Superoxide Radicals", ACS Omega, 5(29), 18007-18012. https://doi.org/10.1021/acsomega.0c01257.
  144. Zhang, H., Sun, M., Song, L., Guo, J. and Zhang, L. (2019), "Fate of NaClO and membrane foulants during in-situ cleaning of membrane bioreactors: Combined effect on thermodynamic properties of sludge", Biochem. Eng. J., 147, 146-152. https://doi.org/10.1016/j.bej.2019.04.016.
  145. Zhang, S., Zhang, J., Ma, Y. and Pak, R.Y. (2021), "Vertical dynamic interactions of poroelastic soils and embedded piles considering the effects of pile-soil radial deformations", Soil. Found., 61(1), 16-34. https://doi.org/10.1016/j.sandf.2020.10.003.
  146. Zhang, W., Tang, Z., Yang, Y., Wei, J. and Stanislav, P. (2021), "Mixed-Mode Debonding Behavior between CFRP Plates and Concrete under Fatigue Loading", J. Struct. Eng., 147(5), 04021055. https://doi.org/10.1061/(ASCE)ST.1943-541X.0003032.
  147. Zhao, R., Zhang, L., Fan, G., Chen, Y., Huang, G., Zhang, H., ... & Guan, X. (2021), "Probing the exact form and doping preference of magnesium in ordinary Portland cement clinker phases: A study from experiments and DFT simulations", Cement Concrete Res., 144, 106420. https://doi.org/10.1016/j.cemconres.2021.106420.
  148. Zheng, J., Zhang, C. and Li, A. (2020), "Experimental investigation on the mechanical properties of curved metallic plate dampers", Appl. Sci., 10(1), 269. https://doi.org/10.3390/app10010269.
  149. Zhu, J., Yang, K., Chen, Y., Fan, G., Zhang, L., Guo, B., ... & Zhao, R. (2021), "Revealing the substitution preference of zinc in ordinary Portland cement clinker phases: A study from experiments and DFT calculations", J. Hazard. Mater., 409, 124504. https://doi.org/10.1016/j.jhazmat.2020.124504.
  150. Zhu, L., Zhang, C., Guan, X., Uy, B., Sun, L. and Wang, B. (2018), "The multi-axial strength performance of composited structural BCW members subjected to shear forces", Steel Compos. Struct., 27(1), 75-87. https://doi.org/10.12989/scs.2018.27.1.075.
  151. Ziaei-Nia, A., Shariati, M. and Salehabadi, E. (2018), "Dynamic mix design optimization of high-performance concrete", Steel Compos. Struct., 29(1), 67-75 https://doi.org/10.12989/scs.2018.29.1.067..