• 한국재료학회지
• /
• 제12권2호
• /
• pp.146-152
• /
• 2002

Effect of polyaniline and additives on surface appearance of Zn electrodeposition was investigated by SEM and XRD analyzing. We carried out the experiment from sulfate Zinc bath containing sulfonated polyaniline, gelatin and thiourea by EG(Electrogalvanizing) simulator. Addition of polyaniline and gelatin in bath, crystal size and shape of hexagonal plane of Zn crystal reduced. Mixing of thiourea, however, brittle deposits were observed because of the difference between vertical growth and parallel growth. (1011) peak appeared with polyaniline and gelatin in XRD analysis. In case of mixing of polyaniline, gelatin and thiourea, (1011) peak appeared and intensity of Zn basal plane decreased. These results suggested that overpotential increased with addition of polyaniline and additives In bath.

• 한국전기전자재료학회논문지
• /
• 제22권8호
• /
• pp.682-688
• /
• 2009

A periodic away of zinc oxide(ZnO) micro-rods as fabricated by using chemical bath deposition and photo-lithography. Vertically aligned ZnO micro-rods array was successfully grown by chemical bath deposition method on ZnO seed layer. The ZnO seed layer was deposited on glass and the patterning was made by standard photo-lithography technique. The selective growth of ZnO micro-rods as achieved with the masked ZnO seed layer. The fabricated ZnO micro rods were found to be single crystalline and have grown along hexagonal c-axis direction of (0002) which is same as the preferred growth orientation of ZnO seed layer.

• 한국표면공학회지
• /
• 제48권1호
• /
• pp.27-32
• /
• 2015

Advanced high strength steels undergo recrystallization annealing in reducing gas atmosphere before galvanizing to improve mechanical properties. The selective oxidations of elements such as Mn, Si, Cr and Al during annealing decrease wettability of liquid zinc, resulting in bare spots and other defects. In this work, Fe-3wt%Mn steel sheet was annealed at $780^{\circ}C$ for 1200 sec. in 5% $H_2-N_2$ atmosphere and then dipped into zinc bath held at $460^{\circ}C$, which contained 0.2wt% dissolved Al. MnO crystallines in the average size of 200 nm were formed on the surface after annealing. It is estimated that MnO has been detached into bath with the formation and growth of inhibition layer with longer immersion time during galvanizing. No evidence of aluminothermic reduction of MnO has been found in this study.

• 한국표면공학회지
• /
• 제30권2호
• /
• pp.128-135
• /
• 1997

The effect of the polyethyledglycol(PEG) on the surface morphology and crystal orientation of electrodeposited zinc from a chloride (1.5M Zinc+7.0M chloriode) have been studied by means of electrochemical methodes, scanning electron microscopy, surface appearance measurement and X-ray diffraction patterns. The resistance of electrodeposit increased, whereas the evolution of hydrogen decreased with incrasing of molecular weight of the PEG. Large grains of electrodeposit were obtained from bath in the absence of organid additive. When the PEG was added, fine grained crystals were observed and the surface roughness was relatively small, but surface appearance deteriorated. The preferred orientation with a(101) plane parallel to the surface was obtained from the PEG addited bath.

• Advances in nano research
• /
• 제14권6호
• /
• pp.557-573
• /
• 2023

The rapid growth of zinc-oxide (ZnO) nanostructures (NSs) on woven carbon fiber (WCF) is reported in this study employing a microwave-aided chemical bath deposition process. The effects of different process parameters such as molar concentration, microwave duration and microwave power on morphologies and growth rate of the ZnO on WCF were studied. Furthermore, an attempt has been taken to study influence of different type of growth solutions on ZnO morphologies and growth rates. The surface functionalization of WCF fabrics is achieved by successful growth of crystalline ZnO on fiber surface in a very short duration through one-step microwave synthesis. The morphological, structural and compositional studies of ZnO-modified WCF are evaluated using field-emission scanning electron microscopy, X-ray diffraction and energy dispersive X-ray spectroscopy respectively. Good amount of zinc and oxygen has been seen in the surface of WCF. The presence of the wurtzite phase of ZnO having crystallite size 30-40 nm calculated using the Debye Scherrer method enhances the surface characteristics of WCF fabrics. The UV-VIS spectroscopy is used to investigate optical properties of ZnO-modified WCF samples by absorbance, transmittance and reflectance spectra. The variation of different parameters such as dielectric constants, optical conductivity, refractive index and extinction coefficient are examined that revealed the enhancement of optical characteristics of carbon fiber for wide applications in optoelectronic devices, carbon fiber composites and photonics.

• 한국표면공학회지
• /
• 제31권6호
• /
• pp.379-388
• /
• 1998

The iron-zinc interfacial reaction and corrosin properties in galvanizing bath containning Ni have been intestigated. The substrate steel plates were galvanized in Zn or Zn-0.018Al baths with various Ni contents. The corrosion resistance of galvanized specimens was also evaluated by $60^{\circ}$bending test for galvannealing speaaimens. The corrosion resistance was improved with Ni addition in pure Zn bath, while deteriorated with Ni addition in Zn-0.18Al bath. The anti-powdering property, on thhe otherhand, was improved with Ni addition in Zn-0.18Al bath, while deteriorated with Ni addition in pure Zn. It was found that the anti-powdering property was improved with increasing $\xi$ phase ratio in reaction layer.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2001년도 춘계학술발표회 초록집
• /
• pp.48-49
• /
• 2001

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.25-26
• /
• 2000

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.37-37
• /
• 2000

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2001년도 춘계학술발표강연 및 논문개요집
• /
• pp.35-35
• /
• 2001