• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.556-561
• /
• 2005

The steel shows plastic deformation after the yield point exceeds. The plastic deformation due to overloads occurs at the interior support of a continuous bridge. The plastic deformation is concentrated at the interior support and the permanence deformation at the interior support remains after loads apply. Because local yielding causes the positive moment at the interior support, it is called 'auto-moment'. Auto-moment redistributes the elastic moment. Because of redistribution, auto-moment decreases the negative moment at the interior support of a continuous bridge. In this paper, the plastic rotation is evaluated using the moment-rotation curve proposed by Schalling and Beam-line method. Moreover, auto-moment is derived from the experiment curve.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.443-446
• /
• 1997

This paper raises issues in testing the absorption coefficients of sound-absorptive samples in the standing wave tube according to the Korean standard of KS F 2814. The code does not consider any effect of air-damping during test. This limitation has been shown to yield much variation of sound absorption coefficients for recent sample tests whose coefficients are less than 10 %. An improved method of calculating the sound absorption coefficients is proposed in this work and its effectiveness in real test is also illustrated. Finally, the guide line for the modification of our national standard code KS F 2814 is suggested for the future.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.04a
• /
• pp.33-40
• /
• 1998

Although a structural analysis based on e linear elastic theory yields good results for deformations and stresses produced by working loads, it fails to assess the teal load-carrying of the plates on the verge of yielding. In case of a limit analysis of plates, the yield line theory is widely used on the basis of the upper bound theorem and theoretically it overestimates the strength of the plate. There is, therefore, a general need for analytical methods of predicting the inelastic behavior and load-carrying capacities of plate subjected to arbitrary loadings and boundary conditions. The $\rho$-version of finite element method has been presented for determining the accurate limit load of plates. The numerical results by $\rho$-version model compares with the results obtained by the h-version software ADINA as well as with the available analytical solutions in literatures.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.21 no.2
• /
• pp.35-42
• /
• 1984

A line integral is exhibited which has the same value for all paths surrounding the tip of crack in a two dimensional strain field of elastic-plasticc material. Finite element method was used to determine Rice's J-integral value in centrally cracked plate. These numerical J-integral values were compared with corresponding values of reference with low hardening and high yield strength. The J-integral value was also computed for a crack extension and different load condition. For increasing crack length the value of J-integral also increases, this means that the crack is unstable. To prove path independent, three paths were used in the analysis and proved.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.80-93
• /
• 1996

A 2-dimensional FEM/GEM program was developed under the plane strain assumption using linear line elements for analyzing stretch/draw forming operations of an arbitrarily shaped draw-die. FEM formulation adopted a new algorithm for solving force equilibrium as well as non-penetration condition simultaneously. Also, a rigid-viscoplastic material model with Hill's normal anisotropic yield condition and rate-sensitive hardening law is assumed, along with the Coulomb friction law in the contact regions. For the case of numerical divergence at nearly final forming stages, geometric force equilibrium method(GEM) is also introduced. The developed program was tested by simulating the forming processes of cylindrical punch/open die, and the drawing processes of automotive oilpan and hood inner panel in order to verify the usefulness and validity of FEM/GEM formulation. The numerical simulation verified the validity and robustness of developed program.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1992.06a
• /
• pp.23-28
• /
• 1992

The purpose of this paper is to develop a new adaptive echo canceller improving convergence speed and near-end-talker detection performance of the conventional echo canceller. In a conventional adaptive echo canceller, an adaptive digital filter with TDL(Tapped-Delay Line) structure modelling the echo path uses the LMS(Least Mean Square) algorithm to cote the coefficients, and NET detector using energy comparison method prevents the adaptive digital filter to update the coefficients during the periods of the NET signal presence. The convergence speed of the LMS algorithm depends on the eigenvalue spread ratio of the reference signal and NET detector using the energy comparison method yields poor detection performance if the magnitude of the NET signal is small. This paper presents a new adaptive echo canceller which uses the pre-whitening filter to improve the convergence speed of the LMS algorithm. The pre-whitening filter is realized by using a low-order lattice predictor. Also, a new NET signal detection algorithm is presented, where the start point of the NET signal is detected by computing the cross-correlation coefficient between the primary input and the ADF(Adaptive Digital Filter) output while the end point is detected by using the energy comparison method. The simulation results show that the convergence speed of the proposed adaptive echo canceller is faster than that of the conventional echo canceller and the cross-correlation coefficient yield more accurate detection of the start point of the NET signal.

• Journal of Positioning, Navigation, and Timing
• /
• v.5 no.1
• /
• pp.1-9
• /
• 2016

Range-based wireless localization system must measure accurate range between a mobile node (MN) and reference nodes. However, non-line-of-sight (NLOS) error caused by the spatial structures disturbs the localization system obtaining the accurate range measurements. Localization methods using the range measurements including NLOS error yield large localization error. But filter-based localization methods can provide comparatively accurate location solution. Motivated by the accuracy of the filter-based localization method, a filter residual-based NLOS error estimation method is presented in this paper. Range measurement-based residual contains NLOS error. By considering this factor with NLOS error properties, NLOS error is mitigated. Also a process noise covariance matrix tuning method is presented to reduce the time-delay estimation error caused by the single dynamic model-based filter when the speed or moving direction of a MN changes, that is the used dynamic model is not fit the current dynamic of a MN. The presented methods are evaluated by simulation allowing direct comparison between different localization methods. The simulation results show that the presented filter is more accurate than the iterative least squares- and extended Kalman filter-based localization methods.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.31 no.2
• /
• pp.82-91
• /
• 1989

This study was carried out to get the basic information of irrigation plans for the red pepper, such as optimum irrigation level and irrigation requirement in Taegu and Kyungpook province. In this study, red peppers were cultivated in 6 PVC pot lysimeters filled with 60cm deep clay loam soil. Four tensiometers were installed in each plot to measure the soil water pressure head. Field measurements were made during the period June 6 to October 31, 1988 at the experimental farm of Kvungpook National University. Six levels of irrigation were used. They were PF 1.8-2.0, PF 2.2-2.4, PF 2.8-3.0, FC-PF.1.7, FC-PF 2.2, and FC-PF 2.7. The results obtained from this study are summarized as follows : 1. In case of irrigation levels of narrow ranges of water contents, the higher the soil water content was, the larger the ET was. Hut in case of the irrigation levels returning to the field capacity, the lager the PF value of irrigation point was, the larger the ET was. Considering ET, yield and weight per fruit, the latter is much better than the former irrigation method. 2. The mean daily ET and mean ET ratio for each 10-day period showed that the maximum value occured in the last of August. The ranges of those were 3.74-14.64 mm/day and 0.87-3.40, respectively. These values showed that small during the early stage of growth, large during the middle stage and getting smaller in the last stage. 3. In case of irrigation levels of narrow ranges of water contents, the increase of irrigation water supplied increased the ET. The relationship between the two showed nearly straight line. Most of irrigated water was consumed as ET and the rest as percolation. But, in case of irrigation levels returning to the field capacity, the higher the PF value of irrigation point was, the larger the ET ratio was. However, their relationship didn't show straight line. 4. The irrigation level of PC - PP 2.7 was found to be the optimum irrigation level with respect to the yield, the weight per fruit, stem length, irrigation requirement and percolation quantity. In this case, mean daily ET and mean ET ratio were 6.79 mm/day (total 10052 mm) and 1.67, respectively. The maximum mean daily ET and mean ET ratio for 10-day period were 14.64 mm/day and 3.40, respectively, in the last of August, and the maximum daily ET was 2126 mm/day on August 24. 5. In case of PC - PP 2.7 which is found the optimum irrigation level, mean irrigation water required, mean ET and mean percolation water quantity were 7.44 mm/day, 6.79 mm/day(91.3% of irrigation water), and 0.38 mm/day (5.5% of it), respectively.

• Korean Journal of Breeding Science
• /
• v.40 no.4
• /
• pp.512-516
• /
• 2008

A new naked oat cultivar 'Choyang' (Avena sativa L.) was developed by the breeding team at the Department of Rice and Winter Cereal Crop, NICS, RDA in 2007. It was derived from a cross between 'Sikyonggwiri' and 'Gwiri23'. The cultivar, Sikyonggwiri is early heading while the breeding line Gwiri23 has a high yielding potential with large-size grain. Bulk method combined with pedigree selection program was employed in subsequent generations, and the promising line SO96025-B-303-44-2-5 was selected for agronomic performance in 2002. The line showed both high yield and good husking rate of seed in the Yield Trial tested at Suwon in 2003 to 2004, and was subsequently designated as 'Gwiri57'. Gwiri57 was evaluated for winter hardiness, earliness, and yield in four locations, Gimje, Iksan, Jeongeup and Jinju from 2005 to 2007 and was released as Choyang. Choyang headed 11 days earlier and matured 5 days earlier than the check cultivar 'Sunyang' in the paddy field condition. The new cultivar Choyang had 97 cm of culm length and 23.4 cm of spike length, 658 spikes per $m^2$, 75 grains per spike, 28.8 g of 1,000-grain weight, and 636 g of test weight. Choyang showed better winter hardiness than that of the check cultivar Sunyang, and similar seed quality to the check cultivar in respect to crude protein (12.9%) and ${\beta}$-glucan content (4.7%). However, it showed higher husking rate than the check cultivar. The grain yield of Choyang in the regional yield trial for 3 consecutive years was averaged $4.67MT\;ha^{-1}$, which was 38% higher than that of the check cultivar Sunyang. Choyang is recommended for the fall sowing cropping only in the southern area where daily minimum mean temperatures are averaged higher than $-4^{\circ}C$ in January, and is not recommended the in mountain area where frost damage is presumable.

• Applied Biological Chemistry
• /
• v.25 no.4
• /
• pp.232-238
• /
• 1982

From ^{15}N$ labelled nitrogen experiments on 13 fields use efficiency by difference method was higher than that by labelling method in 80% of fields tested indicating augmentation of soil nitrogen uptake by fertilizer nitrogen. Both methods showed very similar trend among fields. Sulfur coated urea(SCU) and point application increased fertilization efficiency(yield increment per fertilizer nitrogen applied, Fe) to 23 from 15 of split application through the increase of fertilizer use efficiency from 29(Eu) to 50 but tended to decrease efficiency of absorbed fertilizer nitrogen(yield increment per nitrogen derived from fertilizer, Ef) from 50. to 46 High yielding capacity of Tongil line appears to be attributed to the higher Ef, translocation efficiency and soil nitrogen preference index(soil nitrogen increment in plant per the increment of fertilizer nitrogen in plant, PI). This studies confirmed that yield under fertilizer application system depends on Fe which is the multiplication of Eu and Ef and that the improvement of fertilizer management(form, application method and time) increases principally Eu, the limit of which is controlled by Ef that is attributed mainly to varietal characteristics.