• Journal of Environmental Health Sciences
• /
• v.29 no.3
• /
• pp.72-78
• /
• 2003

In the process of producing chitosan from crustacean shell, the use of excessive acid and alkli is causing the problems of environmental pollution and of production cost. In this study, one way to solve these problems is to cultivate fungi, then, to extract chitosan from the cell wall. By means of flask incubation and batch cultivation, the optimum cultivation conditions for mass production of continuous cultivation was found. Four strains used for the production of fungal chitosan were Gongronella butleri IF08080, Absidia coerulea IF05301, Rhizopus delemar IF04775, Mucor tuberculisporus IF09256. In flask incubation to select strain of producing much chitosan by means of experiment of the effect of initial pH, Absidia coerulea IFO 5301 had highest yield in FCs, 258.1 $\pm$ 47.3 mg/200 $m\ell$l at pH 6.5. In flask incubation under the optimum cultivation condition, temperature 27$^{\circ}C$, culture time 6days, glucose 2%, peptone 1%, (NH$_4$)$_2$ SO$_4$ 0.5%, $K_2$HPO$_4$ 0.1 %, Nacl 0.1 %, MgSO$_4$ㆍ7$H_2O$ 0.05%, CaCl$_2$ㆍ2$H_2O$ 0.01 %, the yield of DCW brought the highest yields. In batch bioreactor, the optimum cultivation condition was that cell suspended solution was 70 $m\ell$, aeration rate 0.5 l/min, agitation rate 800 rpm, culture time 36 hr. In continuous bioreactor, the optimum substrate flow rate was 4 ι/day.

• Journal of Korea Foundry Society
• /
• v.40 no.3
• /
• pp.66-75
• /
• 2020

The aim of this study was to optimize a solid solution treatment for a high pressure die casting Al-10Si-0.3Mg-0.6Mn alloy to avoid blistering and to improve the strength of the alloy. To achieve this goal, the number density of the blisters and the strength of the alloy under various solid solution treatment (SST) conditions were evaluated. The SST was performed at 470, 490, 510 and 530℃ for 20, 60, 120, 240 and 480 min on the alloy. The number density of the blisters increased with the increasing temperature and time of the SST and the defect area fraction. The yield strength of the alloy after the T6 heat treatment increased with the increasing SST temperature and time. Based on the results, it is suggested that SST should be performed at 510℃ within 60 min. or at 470 and 490℃ within 240 min. to avoid blistering and to improve the strength.

• Korean Journal of Food Science and Technology
• /
• v.25 no.1
• /
• pp.78-82
• /
• 1993

This study was carried out to develop a new processing method for the production of yeast autolyzate (YA) by which the yield and the quality could be improved, compared to the conventional method. The result indicated that 85.3% of yeast cell walls treated with glucanase and protease was ruptured by homogenizing at 10,000 psi. Alkali treatment, however, was not effective in disintegrating yeast cell walls. Optimum conditions for autolysis of ruptured yeast cells, obtained with help of response surface methodology (RSM), were pH 7.0, $30^{\circ}C$, ethanol 4% and salt 3%. YA produced by the developed method had significantly higher yield and better sensory quality than that produced by the conventional method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.1
• /
• pp.50-57
• /
• 2016

We studied the Lab-scale process for the development of DNAM in aspect of safety and overall efficiency. Melamine is used for starting material of process, DNAM was synthesized by oxidation and nitration reaction. In order to optimize the process parameters with the product in higher yield and purity, a systematic study with variation of different parameters like molar ratio of nitrating mixture, conditioning time and order of reactant was carried out. The optimized reaction conditions for the synthesis of DNAM were : conditioning time of $3{\pm}3.5$ hour and nitrating mixture in 1:1.4 molar ratio. In order to proceed a stable reaction, melamine was added with enough time to relieve reaction heat. From these reaction condition, DNAM could be obtained in a yield of more than 60%.

• Journal of Ginseng Research
• /
• v.40 no.2
• /
• pp.105-112
• /
• 2016

Background: Minor saponins or human intestinal bacterial metabolites, such as ginsenosides Rg3, F2, Rh2, and compound K, are more pharmacologically active than major saponins, such as ginsenosides Rb1, Rb2, and Rc. In this work, enzymatic hydrolysis of ginsenoside Rb1 was studied using enzyme preparations from cultured mycelia of mushrooms. Methods: Mycelia of Armillaria mellea, Ganoderma lucidum, Phellinus linteus, Elfvingia applanata, and Pleurotus ostreatus were cultivated in liquid media at $25^{\circ}C$ for 2 wk. Enzyme preparations from cultured mycelia of five mushrooms were obtained by mycelia separation from cultured broth, enzyme extraction, ammonium sulfate (30-80%) precipitation, dialysis, and freeze drying, respectively. The enzyme preparations were used for enzymatic hydrolysis of ginsenoside Rb1. Results: Among the mushrooms used in this study, the enzyme preparation from cultured mycelia of A. mellea (AMMEP) was found to convert ginsenoside Rb1 into compound K with a high yield, while those from G. lucidum, P. linteus, E. applanata, and P. ostreatus produced remarkable amounts of ginsenoside Rd from ginsenoside Rb1. The enzymatic hydrolysis pathway of ginsenoside Rb1 by AMMEP was $Rb1{\rightarrow}Rd{\rightarrow}F2{\rightarrow}$ compound K. The optimum reaction conditions for compound K formation from ginsenoside Rb1 were as follows: reaction time 72-96 h, pH 4.0-4.5, and temperature $45-55^{\circ}C$. Conclusion: AMMEP can be used to produce the human intestinal bacterial metabolite, compound K, from ginsenoside Rb1 with a high yield and without food safety issues.

• Nuclear Engineering and Technology
• /
• v.9 no.4
• /
• pp.211-222
• /
• 1977

The decomposition of all the individual chemicals used in the Harwell inactive vitrification pilot plant has been studied by means of a thermal balance. Weight loss curves to 110$0^{\circ}C$ have been obtained. The four materials (sodium nitrate, cesium nitrate, lithium nitrate and ruthenium nitroso-nitrate solution) showed a greater weight loss than that based on an oxide yield, and hence these compounds of their products of decomposition are volatile below 110$0^{\circ}C$. The remaining materials suffered a weight loss no more than that corresponding to a full yield of the oxide, and hence they were not volatile below 110$0^{\circ}C$. Most of chemicals begin to decompose at less than 75$^{\circ}C$ but the nitrates of cesium, strontium, barium and sodium not until 295$^{\circ}C$ to 59$0^{\circ}C$. The results obtained can be used in the analysis of process conditions in the vitrification and calcination of highly radioactive wastes and also of the thermal decomposition behaviour of mixtures containing those materials.

• Applied Chemistry for Engineering
• /
• v.28 no.6
• /
• pp.649-654
• /
• 2017

An activated carbon was prepared from waste citrus peel produced in large amounts in Jeju Island, Korea, using KOH activation and its characteristics was examined. Under the condition of the KOH ratio between 100 and 300%, activation temperature from 400 to $900^{\circ}C$ and activation time from 0.5 to 1.5 h, the iodine adsorptivity of the activated carbon prepared increased but the yield decreased with respect to the increase of each conditions. The iodine adsorptivity and yield of the activated carbon prepared at the activation time of more than 1.5 h were similar to those of using 1.5 h. In addition, as the KOH ratio increased, the specific surface area and pore volume of the activated carbon increased, but the pore diameter decreased. The activated carbon has an average pore diameter of $20{\sim}25{\AA}$. Also, the activated carbon prepared at 300% KOH and $900^{\circ}C$ for 1.5 h has the highest specific surface area of $1,527m^2/g$ and iodine adsorptivity of 1,246 mg/g.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.5
• /
• pp.578-590
• /
• 2015

The present study examines the influence of slurry composting and biofiltration liquid fertilizer (SCBLF) treatment on the biomass characteristics of yellow poplar, and the optimization of organosolv pretreatment for sugar production. After SCBLF treatment, total exchangeable cation contents of yellow poplar was increased from $3.1g\;kg^{-1}$ to $4.4g\;kg^{-1}$, and as a result, biomass production of yellow poplar was also enhanced by 82.3%. Organosolv pretreatment was conducted with three independent variables: 1) reaction temperature: $133.2^{\circ}C$ to $166.8^{\circ}C$; 2) acid concentration: 0.2% to 1.8%; and 3) reaction time: 1.6 min to 18.4 min. Reaction temperature was the most significant variable in water insoluble solid (WIS) recovery rate. High overall sugar yield was attained from pretreatment conditions approximately 50% of WIS recovery rate, and the highest overall glucose yield (44.0%) was achieved from pretreatment at $140^{\circ}C$ with 1.5% acid concentration for 5 min. Consequently, 21.1% of glucose and 5.8% of xylose were produced from the organosolv pretreatment of SCBLF-treated 8-year-old yellow poplar.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.3
• /
• pp.330-341
• /
• 2014

Andropogon gayanus is an important grass due to its high biomass production, drought tolerance and favorable growth on low fertility acidic soils. Currently, there is little research on the impact of growth stage on the nutritional quality or the degree of $CH_4$ production that may arise from this forage during ruminal fermentation. The objectives of this study were to determine the effects of regrowth stage of A. gayanus on its chemical composition, in vitro production of gas and CH4, as well as in vitro dry matter (DM) digestibility when grown under tropical Brazilian conditions and conserved as hay or as silage. The nutritional value of A. gayanus grass declined with increasing maturity; however digestible DM yield linearly increased. After 112 d of regrowth, A. gayanus produced higher quality silage (higher lactate and lower pH and butyrate content) and higher DM yield. However, the low levels of crude protein at this time would make protein supplementation a necessity for proper rumen fermentation. No differences in $CH_4$ kinetic parameters were found with advancing maturity or preservation method (hay or silage).

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.1
• /
• pp.47-53
• /
• 2018

Objective: The objective of this experiment was to investigate the effects of heat stress on milk protein and blood amino acid profile in dairy cows. Methods: Twelve dairy cows with the similar parity, days in milk and milk yield were randomly divided into two groups with six cows raised in summer and others in autumn, respectively. Constant managerial conditions and diets were maintained during the experiment. Measurements and samples for heat stress and no heat stress were obtained according to the physical alterations of the temperature-humidity index. Results: Results showed that heat stress significantly reduced the milk protein content (p<0.05). Heat stress tended to decrease milk yield (p = 0.09). Furthermore, heat stress decreased dry matter intake, the concentration of blood glucose and insulin, and glutathione peroxidase activity, while increased levels of non-esterified fatty acid and malondialdehyde (p<0.05). Additionally, the concentrations of blood Thr involved in immune response were increased under heat stress (p<0.05). The concentration of blood Ala, Glu, Asp, and Gly, associated with gluconeogenesis, were also increased under heat stress (p<0.05). However, the concentration of blood Lys that promotes milk protein synthesis was decreased under heat stress (p<0.05). Conclusion: In conclusion, this study revealed that more amino acids were required for maintenance but not for milk protein synthesis under heat stress, and the decreased availability of amino acids for milk protein synthesis may be attributed to competition of immune response and gluconeogenesis.