• Structural Engineering and Mechanics
• /
• 제20권2호
• /
• pp.173-189
• /
• 2005

The paper presents a finite element model for studying timber-concrete composite beams under long-term loading. Both deformability of connection system and rheological behaviour of concrete, timber and connection are fully considered. The creep of component materials and the influence of moisture content on the creep of timber and connection, the so-called "mechano-sorptive" effect, are evaluated by means of accurate linear models. The solution is obtained by applying an effective step-by-step procedure in time, which does not require storing the whole stress history in some points in order to account for the creep behaviour. Hence the proposed method is suitable for analyses of composite beams subjected to complex loading and thermo-hygrometric histories. The possibility to accurately predict the long-term response is then shown by comparing numerical and experimental results for different tests.

• Geomechanics and Engineering
• /
• 제12권6호
• /
• pp.899-917
• /
• 2017

Sixty four tests were performed in a steel tank to investigate the axial responses of piles driven into organic soil prepared at two different densities using a drop hammer. Four different pile materials were used: wood, steel, smooth concrete, and rough concrete, with different length to diameter ratios. The results of the load tests showed that the shaft load capacity of rough concrete piles continuously increased with pile settlement. In contrast, the others pile types reached the ultimate shaft resistance at a settlement equal to about 10% of the pile diameter. The ratios of base to shaft capacities of the piles were found to vary with the length to diameter ratio, surface roughness, and the density of the organic soil. The ultimate unit shaft resistance of the rough concrete pile was always greater than that of other piles irrespective of soil condition and pile length. However, the ultimate base resistance of all piles was approximately close to each other.

• 농업생명과학연구
• /
• 제46권1호
• /
• pp.29-34
• /
• 2012

소나무 톱밥보드로 제조된 우드세라믹에 전선을 연결하여 목재 틀과 콘크리트 블록 속에 넣고 통전하여 강화마루판과 합판마루판의 표면온도 상승과 하강변화를 조사 하여 우드세라믹을 온돌마루판 하부소재로 이용할수 있는 가능성을 검토하였다. 통전시간 60분 후 마루판의 표면온도와 처음 시작온도 차이는 강화마루판이 크게 나타나 합판마루판보다 열전달이 빠름을 알 수 있었다. 목재 틀에서 우드세라믹 표면설정온도가 $70^{\circ}C$와 $80^{\circ}C$일 때 60분 후 강화마루판의 표면온도는 각각 $37.8^{\circ}C$와 $39.4^{\circ}C$로 높게 나타나 열전달이 우수하였다. 각 우드세라믹 표면설정온도별 처음 시작온도와 30분후의 표면온도 하강차이는 목재 틀이 콘크리트 블록보다, 강화마루판이 합판마루판보다 커서 온도하강이 빠름을 알 수 있었다. 우드세라믹 자체의 표면온도 하강은 목재 틀보다 콘크리트 블럭에서 하강속도가 빨랐으며, 마루판의 하강속도가 우드세라믹의 하강속도보다 느려 마루판이 오랜 시간 열을 유지하고 있음을 알 수 있었다.

• 한국재난정보학회 논문집
• /
• 제4권1호
• /
• pp.86-100
• /
• 2008

It is needed to classify the kinds of construction and demolition(c&d) debris to 6 catagories of waste concrete, waste asphalt concrete, waste wood, scraps, combustible waste and incombustible waste in order to properly do a separate discharge and to estimate unit generation rate in construction site. Also, in this case, the unit treating cost for mixed wastes should be applied with the unit treating cost for combustible waste. The construction standard materials estimation data is used for basic data for estimating unit generation rate. The mixed wastes in this data should be classified to waste wood, combustible waste and incombustible waste, and their ratio is obtained by using the unit generation rate of Asia Pacific Environment and Management Institute and Seoul Metropolitan Development Institute. The waste amounts generated from newly-built construction can be obtained from multiplying the loss rate by the amount of materials used from construction standard estimation data. Also, those from dismantling construction can be obtained by subtracting waste amount generated during newly-built construction from total input amount of materials in newly-built construction. Those in two cases can be used in construction site. It can be used for estimating the amount generated and establishing the treating plan in the case of setting up the policy of waste management and doing the environment impact assessment.

• 한국건설순환자원학회논문집
• /
• 제7권2호
• /
• pp.84-90
• /
• 2012

폐목재의 활용에 관한 특허동향 분석을 위해 한국특허정보원의 특허정보검색서비스(KIPRIS)에서 관련 키워드로 한국, 미국 및 일본의 특허 검색을 실시하여 2011년 12일 31일까지 특허 등록된 한국 77건, 미국 316건 및 일본 317건의 특허 자료를 수집하였다. 수집된 자료 중 거절, 소멸, 무효, 취하, 포기 및 폐목재와 관련이 적은 내용의 특허를 제외시키고 얻은 한국특허 71건, 미국특허 216건, 일본특허 227건에 대한 분석을 실시하였다. 또한 폐목재를 콘크리트용 경량골재로 활용하기 위한 기초 연구로서 파쇄시킨 소나무 임목부산물을 No. 8(2.4 mm)체로 쳐서 이를 통과시킨 것을 $100{\pm}5^{\circ}C$에서 24시간 동안 건조시킨 다음 잔골재의 일부로서 대체 사용한 모르타르 물성 실험을 실시하였다. 목재와 시멘트를 혼합하는 경우 목재의 수종과 부위에 따라서는 시멘트의 경화를 저해하는 것으로 알려져 있기 때문에 본 연구에서는 파쇄폐목재를 $20^{\circ}C$, $50^{\circ}C$, $80^{\circ}C$ 및 $100^{\circ}C$의 수중에서 일정 시간 동안 침지시킨 후 건조시킨 다음 이를 사용한 모르타르의 물성실험을 실시하여 파쇄폐목재의 전처리 효과를 함께 고찰하였다.

• KIEAE Journal
• /
• 제8권3호
• /
• pp.77-83
• /
• 2008

The effective mixture of structural laminated timber and other materials is expected to extend the potentials of building structures because of the potentials to realize high performance in structural safety. The classical joint types using drift pin and bolts are occurred local failures due to the small bearing area. In result, new joints using H shaped steel were suggested in this research. The objective of this study is to evaluate elasto-plastic behaviors by strengthening types of wood frames with new joints connecting structural laminated timber with H shaped steel. A total of five specimens of about one-second scale were tested. Specimens had columns with 1,050 height and $84mm{\times}100mm$ section, and a beams with 1,950mm length and $130mm{\times}100mm$ section. Also, the specimens were stiffened by brace, hwang-toh brick, and autoclaved lightweight concrete. The results of the test showed that the specimen stiffened with autoclaved lightweight concrete was characterized by fairly good strength and stiffness than those of the other specimens. Initial stiffness of H-2.0D-NS specimen with 2 times inserting length of beam height showed 1.33 times than that of H-1.5D-NS specimen. However, the strength of H-2.0D-NS specimen has not improved too much than H-1.5D-NS specimen.

• 한국건축시공학회지
• /
• 제13권5호
• /
• pp.457-464
• /
• 2013

Traditionally, the material used for the form in reinforced concrete construction has been wood or steel. But recently, aluminum forms have been widely used in wall structures such as apartment buildings. Aluminum is light, easy to handle, and economically advantageous, but the hydrogen gas created due to its reaction with the alkali component in concrete gives rise to air pockets on the concrete's surface, and deteriorates the surface's finishability. In this research, to determine the influence of aluminum material on concrete, the cement paste W/C and its chemical reactivity in alkali and acid solution were analyzed. As a prevention plan, the influence of the number of applications of calcium hydroxide and various surface coating materials was analyzed. Through the analysis, it was found that the surface voids on the aluminum form are the result of the reaction of hydrogen gas with an alkali such as $Ca(OH)_2$. This can be prevented by the surface treatment of $Ca(OH)_2$, separating material and coating material. However, poor surface form and damages to the form are expected to cause quality degradation because of the aluminum-concrete interaction. Therefore, thorough surface treatment, rather than the type of separating material or coating material, is considered the most important target of management.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 학술대회 논문집 전문대학교육위원
• /
• pp.191-193
• /
• 2006

We use electric drill for cutting wood. In electric drills, there is the core-drill that bores concrete-wall. The core-drill is used in construction or remodeling areas. Therefore we require safety in working with the core-drill. In this paper, new controller of core-drill for concrete-wall is proposed. Experimental results show the validity of the proposed controller.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.475-480
• /
• 1999

Recently domestic building market in the face of 3D, in addition to construction cost increase, materials lack problems and opening a building market to foreign countries, is trying to find out the efficient ways of overcoming these problems. So the necessity to study the permanent form is urgent to escape the problems of constructing human power economy, cost down, noises problem, environmental prevention and efficacy of form work to technical improvement will contribute a practical permanent form in field through economic evaluation of permanent form. In this paper, we compared wood form cost with permanent form cost(made form polymer or fly ash) for frame work

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
• /
• pp.19-20
• /
• 2010

본 연구는 전이슬래브의 두께를 줄이고 철근량을 감소시키기 위해 포스트텐션을 전이슬래브에 적용하는 포스트텐션 전이슬래브에 관한 연구이다. 본 논문에서는 전이슬래브와 같이 두꺼운 판요소 해석에 적합한 Wood-Armer 공식과 부착 긴장재를 사용한 포스트텐션 설계방법을 제안하고자 한다.