• Journal of the Korean Wood Science and Technology
• /
• v.25 no.3
• /
• pp.96-104
• /
• 1997

The objective of this research project was to develop the wooden footpath block to reuse of wood waste. Some physical and mechanical properties of the wooden block such as water absorption, thickness swelling, modulus of rupture, internal bond, density profile and impact resistance were studied. Water absorption and thickness swelling of the wooden block were greatly reduced when the wooden block was pressed inside the forming device than by conventional hot pressing. Also, Modulus of rupture and internal bond of the wooden block were increased greatly when the pressing was completed inside the forming device. The density profile of the wooden block was improved up to 93.5%, minimum to average density ratio. The wooden block manufactured in this study have excellent physical and mechanical prperties in comparison with existing wood based materials. So, these wooden blocks are applicable to footpth block or other exterior members.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.2
• /
• pp.52-60
• /
• 1997

Hornbeam trees(Carpinus laxiflora BL.) are growing in Korea and have good characteristics such as relatively high density, fine texture, split- resistance, and white colour. However, they have seldom been used as manufacturing materials This study was carried out to evaluate the possibility of using hornbeam wood as bent, wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of $15{\times}15{\times}350mm$ were used green or air-dried, and were steamed at $100^{\circ}C$ for 20min, or microwave heat ed f or 60 seconds. The bending processing conditions are showed in Table 3. The minimum solid-bending radii of air-dried wood were 40mm for steaming and 200mm for micro-wave heating, respectively. And that of green wood were 40mm for micro-wave heating. In conclusion, both of the steamed wood and micro-wave heated green wood showed very good solid bending processing properties, but micro-wave heated air-dried wood were not sufficient for bent-wood furniture.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.5
• /
• pp.641-651
• /
• 2015

The aim of this study was to estimate the service life of alkaline copper quaternary (ACQ)-treated wood. The service life of preservative-treated wood was estimated by comparing a residual quantity of ACQ in wood with toxic threshold to fungi. Indoor and outdoor leaching tests were carried out in order to predict residual ACQ quantity within wood. As a result, the leaching ratio of ACQ from treated wood above ground via precipitation was 18.1% for 50 years. When the H4 treated wood, which is traditionally used in contact with the ground and fresh water, is used above-ground, the leaching ratio of ACQ for 50 years is 18.1% and the residual quantity of ACQ is $4.2kg/m^3$, which is higher than the toxic threshold of ACQ. Thus, the H4 treated wood used above-ground will be resistant to biodeterioration for at least 50 years.

• Journal of the Korean Wood Science and Technology
• /
• v.11 no.2
• /
• pp.52-60
• /
• 1983

Hornbeam trees(Carpinus laxiflora BL.) are growing in Korea and have good characteristics such as relatively high density, fine texture, split-resistance, and white colour. However, they have seldom been used as manufacturing materials This study was carried out to evaluate the possibility of using hornbeam wood as bent-wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of $15{\times}15{\times}350mm$ were used green or air-dried, and were steamed at $100^{\circ}C$ for 20min, or microwave heated for 60 seconds. The bending processing conditions are showed in Table 3. The minimum solid-bending radii of air-dried wood were 40mm for steaming and 200mm for micro-wave heating, respectively. And that of green wood were 40mm for micro-wave heating. In conclusion, both of the steamed wood and micro-wave heated green wood showed very good solid bending processing properties, but micro-wave heated air-dried wood were not sufficient for bent-wood furniture.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.58-65
• /
• 2008

Most connections for the glulam structural members consisted of connector and fastener. The mechanical behaviour of the connection can be occurred by the dowel bearing resistance and wood shear by the fastener. This study aims at the examination of the shear properties for the small specimen with lamination components and for the full-sized pin connection and the moment resisting property for the double shear full-sized pin connection using structural column and beam members. Small specimens including glue line shows greater density and shear strength by the lamination effect than other specimens. It is needed that estimations of double shear property and moment resistance for the pin connections should be adjusted in some degree. For the better and safe estimation of moment resistance strength for the column-beam pin connection, however, the shear strength of small specimens should be deducted by 10%.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.547-556
• /
• 2019

Thinned, small larch logs have small diameters and no value-added final use, except as wood chips, pallets, or fuel wood, which are products with very low economic value; however, their mechanical strength is suitable for structural applications. In this study, small larch logs were sawed, dried, and cut into square timbers (with a $90mm{\times}90mm$ cross section) that were laterally glued to form core panels used to manufacture cross-laminated timber (CLT) wall panels. The surface and back of these core panels were covered with 12-mm-thick structural plywood panels, used as cross bands to obtain three-ply CLT wall panels. This attachment procedure was conducted in two different ways: gluing and pressing (CGCLT) or gluing and nailing (NGCLT). The size of the as-manufactured CLT panels was $1,220mm{\times}2,440mm$, the same as that of the plywood panels. The final wall panels were tested under lateral shear force in accordance with KS F 2154. As the lateral load resistance test required $2,440mm{\times}2,440mm$ specimens, two CLT wall panels had to be attached in parallel. In addition, the final CLT panels had tongued and grooved edges to allow parallel joints between adjacent pieces. For comparison, conventional light-frame timber shear walls and midply wall systems were also tested under the same conditions. Shear walls with edge nail spacing of 150 mm and 100 mm, the midply wall system, and the fabricated CGCLT and NGCLT wall panels exhibited maximum lateral resistances of 6.1 kN/m (100%), 9.7 kN/m (158%), 16.9 kN/m (274%), 29.6 kN/m (482%), and 35.8 kN/m (582%), respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.5
• /
• pp.471-481
• /
• 2021

This study investigated the hygroscopicity and UV deterioration characteristics of 3 domestic and 4 imported woods using natural oil, stain, and varnish paints. In terms of hygroscopicity, it was found that the hygroscopicity of the painted wood was lower than that of the unpainted wood, and that as the number of coatings increased, the hygroscopicity decreased. In terms of anti-absorption, oil-based chemical paints showed higher resistance than water-based paints, and natural oils showed results comparable to oil-based paints. As for the UV deterioration, the amount of color change of the painted wood was lower than that of the unpainted wood, and there was no significant difference according to the number of times of painting. The amount of color change was found to be low in oil-based paints and hardwoods. Through this study, we confirmed effective moisture blocking and small color changes during painting using paints, and it is believed that wood can be protected from internal and external defects through selective and efficient painting based on data for excellent painting performance.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.344-350
• /
• 2011

In this study, LVLs of radiata pine were fabricated with non-preservative treated veneers, CuAz treated veneers, and ACQ treated veneers, using aqueous vinyl urethane adhesive and phenol modified resorcinol resin adhesive. Then density gradient, bonding strength, bending properties and decay resistance of LVLs were evaluated. As results, the cone-shaped and higher density gradient pattern was found in layer close to glueline. After cyclic water boiled test, the LVL bonded with aqueous vinyl urethane resin adhesive was delaminated in all layers or partly delaminated including check, chasm in glueline layer. In the case of LVL bonded with phenol modified resorcinol resin adhesive, despite slight cupping due to great glueline stress and vertical check between glueline layers, it was observed that the bonding strength to delamination was higher, owing to most absence of delamination through overall glueline. On the other hand, in the decay test, mass loss by brown rot fungi was greater than white rot fungi in LVL bonded with aqueous vinyl urethane resin adhesive. However, in LVL bonded with phenol modified resorcinol resin adhesive, the mass loss by brown rot fungi was slight and non-preservative treated LVL was low. The mass loss of preservative-treated LVL was 0 (zero), showing the high decay resistance effect.

• Current Research on Agriculture and Life Sciences
• /
• v.10
• /
• pp.41-47
• /
• 1992

In general, the behavior of moisture transmission is estimated by vapor permeability or vapor transmission resistance, but its values obtained by experiments do not have great adaptability for practical situations because of changes in the experimental conditions. This fact is why only theoretical discussions have advanced. Thus, the fundamental study of the moisture transmission phenomenon has been treated lightly. Here, as the first step toward the basic research of moisture transmission, the amount of moisture transmission and the moisture distribution in specimens were investigated. The experiment was conducted in a steady state, and the moisture distribution was measured by slicing and weighing the specimens. From the examination of the vapor transmission resistance, the phenomenon of moisture transmission was dealt with devide the moisture transfer on the wood surface and moisture diffusion in wood. The following results were obtained. 1) The phenomenon of moisture transmission should be approached by its division into moisture transfer on the wood surface and moisture diffusion in the wood because the positive values of vapor transmission resistance exist in the extrapolation of thickness 0mm. 2) The distribution of moisture in wood can be illustrated by two straight lines intersecting at the point of nine percent moisture content : namely, diffusion coefficients have two constant values at moisture contents below and above nine percent. The shape of the distribution curve of moisture content is similar irrespective of the wood thickness. On the other hand, when the moisture contents on both sides was more than nine percent, the distribution of the moisture content could be illustrated by one straight lines. 3) The amount of moisture movement is determined by the moisture gradient in wood. 4) Coefficients of the moisture transfer depend on the thickness of the specimens.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.3
• /
• pp.234-246
• /
• 2013

It was found that test piece heated rapidly by 3 kW microwave for 5 minutes satisfies the targeted temperature and the percentage of moisture content, and the highest rate of weight increase is obtained in case of 120 minute immersion in the mixture of phosphates and heterocyclic compounds, from the result of such analysis as: kiln drying schedule, flame retardent by flammability test, insect resistance by termites, and permeability of combined penetrant for the wood after assigning multifunctional finish by immersing conifer structural frame, which is used for the frame work of wooden house and indoor/outdoor finishing in flame retardant and insect repellent materials mixture with the remaining heat of microwave. In addition, after a test of flame retardent treated item, it was identified that every mixture of phosphates corresponds with the standards of flame retardent, and upon investigation of moritality of 7 days after putting termites, it was showed that test piece immersed in the mixture of phosphates and heterocyclic compounds has the best characteristics, showing over 96% of high moritality. From the analysis of inward permeability of combined penetrant for the wood, it was decided that excellent performance in the flame retardent and insect resistance of the wood revealed due to full penetration of combined penetrant as it was found that combined penetrant penetrated through the whole inner cells of the wood.