• International Journal of Highway Engineering
• /
• v.8 no.2 s.28
• /
• pp.55-62
• /
• 2006

Transverse cracks in continuously reinforced concrete pavement (CRCP) occur at early ages due to temperature and moisture variations. The width and spacing of transverse cracks have a significant effect on pavement performance such as load transfer efficiency and punchout development. Also, crack widths in CRCP depend on 'zero-stress temperature,' which is defined as a temperature where initial concrete stresses become zero, as well as drying shrinkage of concrete. For good long-term performance of CRCP, transverse cracks need to be kept tight. To keep the crack widths tight throughout the pavement life, zero-stress temperature must be as low as practically possible. Thus, temperature control at early ages is a key component In ensuring good CRCP performance. In this study, concrete temperatures were predicted using PavePro, a concrete temperature prediction program, for a CRCP construction project, and those values were compared with actual measured temperatures obtained from field testing. The cracks were also surveyed for 12 days after concrete placement. Findings from this study can be summarized as follows. First, the actual maximum temperatures are greater than the predicted maximum temperature in the ranges of 0.2 to 4.5$^{\circ}C$. For accurate temperature predictions, hydration properties of cementitious materials such as activation energy and adiabatic constants, should be evaluated and accurate values be obtained for use as input values. Second, within 24 hours of concrete placement, temperatures of concrete placed in the morning are higher than those placed in the afternoon, and the maximum concrete temperature occurred in the concrete placed at noon. Finally, from the 12 days of condition survey, it was noted that the rate of crack occurrence in the morning placed section was 25 percent greater than that in the afternoon placed section. Based on these findings, it is concluded that maximum concrete temperature has a significant effect on crack development, and boner concrete temperature control is needed to ensure adequate CRCP performance.

• Journal of Korean Society of Transportation
• /
• v.25 no.4
• /
• pp.123-133
• /
• 2007

This study analyzed whether a transit network with hierarchy is efficient or not, and if transit network hierarchy has cost efficiency, then which condition guarantees the efficiency of the transit network hierarchy. The authors modeled the total cost of the transit network and suggested the conditions in which the transit network hierarchy has cost efficiency through comparing the cost of the transit network with and without hierarchy. The efficiency of transit network hierarchy is guaranteed when the travel cost savings induced by using a higher hierarchy transit network is larger than the increasing non-travel cost, which is the sum of access cost, waiting cost, and operating cost, induced by the introduction of a higher hierarchy transit network. This result is consistent with common sense and with the concept of cost and benefit analysis. If a passenger traveling within the area divided by a higher hierarchy transit network uses only a lower hierarchy transit network and the passenger traveling out of the area divided by the higher hierarchy transit network uses both lower and higher hierarchy transit networks, the travel demand using the higher hierarchy transit network is inversely proportional to the square of the line spacing. This means that the transit network becomes more efficient and small increases of travel demand guarantee the efficiency of the transit network hierarchy as the connectivity of the network becomes higher. This result shows that transit networks have economies of aggregation. This study is the first analytical research on transit network hierarchy and is expected to be a basis for numerical research. However, numerical research should complement this study, since analytical research has some limitations for considering a real network.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.6 no.1
• /
• pp.13-26
• /
• 2001

Six ferromanganese crusts from the Lomilik and Litatfooki seamounts in the Marshall Islands were analyzed for texture, geochemistry and stratigraphy to delineate the paleoceanographic conditions. The crusts can be divided into three layers; 1) outermost massive layer (Layer 1), 2) middle porous Fe-oxides rich layer infllled with biointemal clasts (Layer 2), and 3) innermost massive layer cemented and/or replaced by carbonate fluoapatite (CFA) (Layer 3). The Layer 1 contains higher Mn, Co, Ni, and Mg than other two layers, and the Layer 2 was relatively more enriched in Fe, Al, Ti, Ba, Cu, and Zn. However, the Layer 3 shows higher Ca and P and lower Mn, Fe, Co, and Ni contents than overlying two layers. Based on the Co-chronometry, the crusts are postulated to have begun to grow from 56-31 Ma (early Eocene to Oligocene). The boundaries between layers 1 and 2, and layers 2 and 3 are dated to be 7-3 Ma and 26-14 Ma, respectively. High contents of Ca and P in Layer 3 clearly indicate that the layer had been phosphatized prior to the formation of Layer 2. Considering the well-preserved mjcrostructures in Layer 3, it is unlike that the crusts themselves were recrystallized in suboxic condition. Also, the lower Co concentrations in Layer 3 may imply that the Co supply was not constant during the formation of Layer 3. Layer 2, characterized by the porous texture, grew over Layer 3 during 26-9 Ma. Internal biogenic sediments including foraminifera within the original cavities and the enrichment of organophillic elements such as Ba, Cu, and Zn, suggest that Layer 2 have below high production regions. Also, high content of allumino silicate components may indicate increased terrigeneous input during the formation of Layer 2. The Layer 2. The Layer 1 has been subjected to little diagenetic influence since the Pliocene.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.13 no.1
• /
• pp.58-65
• /
• 2010

Purpose: Since there are few studies involving acute pancreatitis in children, we reviewed our experience with this medical condition to describe the clinical features. Methods: A retrospective analysis was conducted by reviewing the medical records of 41 patients with AP who were admitted to the Department of Pediatrics of Pusan National University Hospital between January 1996 and June 2007. Results: Twenty males and 21 females (mean age, 8.7${\pm}$4.5 years) were included. In 22 patients (53.7%), no definitive causes were found. The most common etiologies were choledochal cysts (22.0%). Necrotizing pancreatitis was diagnosed in 5 patients (12.2%), and recurrent acute pancreatitis in 4 patients (9.8%). CT findings included pancreatic swelling (43.9%), peripancreatic fluid collection (29.3%), ascites (24.4%), and peripancreatic fat necrosis (12.2%). Serum amylase and lipase levels at diagnosis were 535.3${\pm}$553.2 and 766.2${\pm}$723.6 U/L, respectively, and were normalized within 1 week in 22 and 14 patients, respectively. On the basis of the Balthazar scale, 2 patients were diagnosed with severe AP. In 4 patients (9.8%), a surgical procedure was indicated. Major complications included ascites (32.3%), sepsis (16.1%), and pseudocyst and renal impairments (12.9%). Two patients died from multi-organ failure. Conclusion: The etiologies of AP in children are varied. Most children have a single episode and a self-limited course. However, AP of childhood still carries significant morbidity and mortality. Early diagnosis, appropriate treatment according to disease severity, and management of complications are important.

• Journal of radiological science and technology
• /
• v.35 no.4
• /
• pp.345-352
• /
• 2012

As the breast cancer rate is increasing fast in Korean women, people pay more attention to mammography and number of mammography have been increasing dramatically over the last few years. Mammography is the only means to diagnose breast cancer early, but harms caused by radiation exposure shouldn't be overlooked. Therefore, it is important to calculate the radiation dose being absorbed into the breast tissue during the process of mammography for a protective measure against radiation exposure. Because it is impossible to directly measure the radiation dose being absorbed into the human body, statistical calculation methods are commonly used, and most of them are supposed to simulate the interaction between radiation and matter by describing the human body internal structure with anthropomorphic phantoms. However, a simulation using Geant4 Code of Monte Carlo Method, which is well-known as most accurate in calculating the absorbed dose inside the human body, helps calculate exact dose by recreating the anatomical human body structure as it is through the DICOM file of CT. To calculate the absorbed dose in the breast tissue, therefore, this study carried out a simulation using Geant4 Code, and by using the DICOM converted file provided by Geant4, this study changed the human body structure expressed on the CT image data into geometry needed for this simulation. Besides, this study attempted to verify if the dose calculation of Geant4 interlocking with the DICOM file is useful, by comparing the calculated dose provided by this simulation and the measured dose provided by the PTW ion chamber. As a result, under the condition of 28kVp/190mAs, the Difference(%) between the measured dose and the calculated dose was found to be 0.08 %~0.33 %, and at 28 kVp/70 mAs, the Difference(%) of dose was 0.01 %~0.16 %, both of which showed results within 2%, the effective difference range. Therefore, this study found out that calculation of the absorbed dose using Geant4 Simulation is useful in measuring the absorbed dose in the breast tissue for mammography.

• Applied Chemistry for Engineering
• /
• v.18 no.4
• /
• pp.314-319
• /
• 2007

The destruction of synthetic acetic acid wastewater was carried out using UV, $O_3$, $H_2O_2$, $Fe^{2+}$ oxidants in various combinations by the advanced oxidation processes. $UV/H_2O_2$, $UV/H_2O_2/Fe^{2+}$, $O_3$, $O_3/H_2O_2$, $UV/O_3/H_2O_2$, $UV/O_3/H_2O_2/Fe^{2+}$ processes were tested. $UV/H_2O_2/Fe^{2+}$, $O_3/H_2O_2$, $UV/O_3/H_2O_2$, $UV/O_3/H_2O_2/Fe^{2+}$ processes shows the most effective destruction efficiency at low pH (3.5) condition of wastewater, but $UV/H_2O_2$ and $O_3$ processes were observed less than 20%. Destruction efficiency was gradually increased with the reaction time in the $O_3/H_2O_2$ and $UV/O_3/H_2O_2$ processes, in case of the $UV/H_2O_2/Fe^{2+}$ and $UV/O_3/H_2O_2/Fe^{2+}$ processes shows rapid increasing of destruction efficiency within 90 min, then slightly decreasing with time. The destruction efficiencies of $UV/H_2O_2/Fe^{2+}$, $O_3/H_2O_2$, $UV/O_3/H_2O_2$ and $UV/O_3/H_2O_2/Fe^{2+}$ processes were observed 55, 66, 66 and 64%, respectively.

• Journal of Sericultural and Entomological Science
• /
• no.12
• /
• pp.37-45
• /
• 1970

The processing management forms of our country's filature factories in 1969 are summarized as follows. (1) About 80％ of total cocoon collection is made within 5 days involving peak day, and 10％ of cocoon collection is finished until 3 days before and after the peak day, (2) About 92％ of alive cocoons transported on unpaved road, and about 40％ of the cocoons purchased by all factories are loaded on trucks from common selling station which is far beyond 40km, therefore a new packing system of alive cocoons to drop the damage of cocoon qualities, should be taken. (3) 22％ of all factories in our. country have only low-temperature cocoon drying machine. Therefore the installment of hot-air cocoon drying machine is required urgently. (4) In view of cocoon qualities in our country, the grouping method of cocoon for reeling. taken by about 50％ of the factories at percent, which classify cocoons for reeling as high group (1,2,3,4 grades) and low group(5,6 grades), will have to be replaced by the method tat classify them high group (1,2 grades) middle group (3,4 grades), low group (5,6 grades). (5) The .ratio of cocoon assorting stood about 10％ in multi-ends reeling, about 15％ in automatic reeling, conclusively, the ratio of cocoon assorting for automatic reeling was higher tan that for multi-ends reeling. One person's ability for a day in cocoon assorting reaches to about 80-100kg. (6) Cocoon cooking condition requires the increase of the cooking time, the pressure and temperature used to be prolonged as much as the qualities of cocoons are material cocoon ior automatic and double cocoon machines are treated uncompletely. (7) Automatic silk reeling is being performed at 1-2$^{\circ}C$ lower in reeling water temperature and operated at about twice velocity. (8) The temperature and humidity of rereeling room stood at 25$^{\circ}C$, 67.2％ R.H and 32.3$^{\circ}C$, 51.9％ R.H of rereeling machine are showed, Average rereeling velocity is 233m/min and large reefs charged for one person are 7.5 reels and form of skein used in all factories is double skein. (9) About 73％ of water sources for filature used under-earth water. About 48％ of all filature factories in our country have not yet water purifying equipments. Installation of the equipment for these factories seems to be urgent, (10) Denier .balance, sizing reel, seriplane, are being used in most factories as self-inspection apparatus. (11) More than 90％ of the factories use the vacum tank in rereeling process and about 20％ of them use it in cocoon cooing process (12) Only 21％ of the factories use chemicals in filature process. About all them use "Seracol 100" in cocoon cooking process and "Seracol 500" in rereeling process, (13) Above survey results explain each all factories show large difference in the processing management. Therefore, it is believed that intercommunication through seminar or technical exchange will contribute to the production evaluation of cocoon in our filature industry.

• Food Science of Animal Resources
• /
• v.28 no.1
• /
• pp.51-58
• /
• 2008

This study was performed to evaluate the physico-chemical properties of fermented sausages containing probiotic starter cultures (LK-30 plus, Lactobacillus plantarum 155 and 167, and Pediococcus damnosus L12) with reduced fat levels, and to determine the optimum condition for the manufacture of these products. Although low-fat fermented sausages were reduced fat content at the amount of 90% and the ripening time by 1-2 weeks, as compared to regular-fat counterpart, they became harder and had many winkles outside due to the extreme drying. In addition, fat level in fermented sausages affected the composition and shear force values. During ripening, pH, lightness and yellowness values tended to decrease, however, microbial counts of inoculated lactic acid bacteria were increased up to $10^8-10^9cfu/g$ within 3 days and remained constant thereafter. Low-fat fermented sausages had higher microbial counts than regular-fat ones. Although the inoculated probiotic starter cultures alone had the functional properties, such as cholesterol reduction, anti-high blood pressure and antimicrobial activity, they did not have distinctive characteristics in the fermented sausages. Based on these results, the low-fat fermented sausages were successfully manufactured, but a little bit increased fat level and improved functional properties in the fermented sausages would be required to have better quality as compared to regular-fat counterparts.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.18 no.2
• /
• pp.74-87
• /
• 2016

Potato phenology, growth, and yield are projected to be highly affected by global warming in the future. The objective of this study was to examine the responses of potato growth and yield to environmental elements like temperature, solar radiation, and daylength. Planting date experiments under open field condition were conducted using three cultivars differing in maturity group (Irish Cobbler and Superior as early; Atlantic as mid-late maturing) at eight different planting dates. In addition, elevated temperature experiment was conducted in four plastic houses controlled to target temperatures of ambient temperature (AT), $AT+1.5^{\circ}C$, $AT+3^{\circ}C$, and $AT+5^{\circ}C$ using cv. Superior. Tuber initiation onset was found to be hastened curve-linearly with increasing temperature, showing optimum temperature around $22-24^{\circ}C$, while delayed by longer photoperiod and lower solar radiation in Superior and Atlantic. In the planting date experiments where the average temperature is near optimal and solar radiation, rainfall, pest, and disease are not limiting factor for tuber yield, the most important determinant was growth duration, which is limited by the beginning of rainy season in summer and frost in the late fall. Yield tended to increase along with delayed tuber initiation. Within the optimum temperature range ($17^{\circ}-22^{\circ}C$), larger diurnal range of temperature increased the tuber yield. In an elevated temperature treatment of $AT+5.0^{\circ}C$, plants failed to form tubers as affected by high temperature, low irradiance, and long daylength. Tuber number at early growth stage was reduced by higher temperature, resulting in the decrease of assimilates allocated to tuber and the reduction of average tuber weight. Stem growth was enhanced by elevated temperature at the expense of tuber growth. Consequently, tuber yield decreased with elevated temperature above ambient and drop to almost nil at $AT+5.0^{\circ}C$.

• Journal of the Korean association of regional geographers
• /
• v.2 no.1
• /
• pp.69-85
• /
• 1996

This research adoptes a spatial analysis function of the Geographic Information System[GIS] to analyze the location and the service district of a collective consumption facility, to discover the optimal location, and to redefine the service district. The location and spatial district of a collective consumption facility strongly influences the quality of life of residents. This research studies administrative offices and districts, especially Gu-offices in Ulsan. Ulsan would be raised to the status of Kwangyokshi in 1997; so that, the status of four Gus would be changed from a general administration into a self-governing administration. The summary of this research focuses on five significant points. First, the districts of four Gus were strongly required to be redefined to obtain the maximization of the degree of potential development as well as of the efficiency and equity of administring services. The spatial range of residents in a Gu was not in accord with its administrative district. The administrative districts of four Gus in Ulsan were not balanced in terms of area and population, and the high degree of disparity among Gus existed the efficiency and equality of a collective consumption service. Second, the current gu-offices were located based on security of land and accessibility of a main route; so, there was difficult to find the creteria and the principles of selections of the location of Gu offices. The social disparity of an administrative service existed in the accessibility into Gu-offices. Third, the administrative districts of Gus were redefined with spatial analysis tool of ARC/INFO. It was recommended that Ulsan maintain four Gus under the condition of five Kwangyokshi in South Korea. The redefined districts of administration reduced the disparity among four Gus in terms of area and population. improved the degree of harmony between the spatial range of residents of Gus and the administrative district of Gus, and increased the efficiency and equity of administrative service. Fourth, within the redefined adminis trative district of a Gu, the centroid reduced the maximum distance and mean distance; so, the efficiency and equity of public service provided by the Gu-office were improved. Last, the spatial analysis function of GIS helped to select the optimal location and to delineate the district of public service with more speedly and objectively. The function of spatial analysis of GIS was very useful to minimize the conflict in the determination of the location of a collective consumption facility and of the service district. To improve location analysis with GIS. non-spatial data base such as budget, thought of residents, and development policy and program, should be constructed.