• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.4
• /
• pp.502-509
• /
• 2013

It presents an efficient switching pattern, which expects a reduction of switching losses in a cascaded H-bridge PWM multilevel inverter. By the proposed switching scheme, the lower H-bridge module operates at low frequency of 60[Hz] because it assigns to transfer most load power. The upper H-bridge module operates at high frequency of PWM switching to improve THD of output voltage. The proposed switching pattern applies to cascaded H-bridge multilevel inverter with PD, APOD, bipolar, and unipolar switching methods. By computer-aided simulations, we verify the validity of the proposed switching scheme. Finally, we prove that the proposed PD and APOD switching patterns are better than those of the conventional one in efficiency.

• The Journal of Korean Physical Therapy
• /
• v.26 no.1
• /
• pp.27-32
• /
• 2014

Purpose: The purpose of the study was to comparison of trunk muscle activity during static standing position and standing position on therapeutic climbing wall of adult. Methods: Study subject is arbitrarily classified into 10 of experimental group and 10 control group among 20 of adult. Trunk activity measured as rectus abdominalis, external oblique, internal oblique, erector spinae. Control group maintains that center of gravity of trunk pass the front of shoulder, pelvis, knee and ankle on stable surface with putting legs apart more than shoulder width. Experimental group had static exercise on 4 by 3 meter, 90 degree of Therapeutic climbing wall. Starting position is that putting arms and legs apart more than shoulder width. In order to compare the effect of it between the groups, independent t-test was used. Results: According to the test result, significant difference between among rectus abdominalis, erector spinae the experimental groups. And external oblique, internal oblique muscle atvity is no significant difference experimental groups between among the control groups was observed. Conclusion: Trunk muscle activation is activated to standing position on the Therapeutic Climbing Wall more than static standing position.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.7
• /
• pp.756-759
• /
• 2014

DC/DC converters are commonly used to generate regulated DC output voltages with high-power efficiencies from different DC input sources. The converters can be applied in the regenerative braking of DC motors to return energy back to the supply, resulting in energy savings for the systems at periodic intervals. The fundamental converter studied here consists of an IGBT (Insulated Gate Bipolar mode Transistor), an inductor, a capacitor, a diode, a PWM-IC (Pulse Width Modulation Integrated Circuit) controller with oscillator, amplifier, and comparator. The PWM-IC is a core element and delivers the switching waveform to the gate of the IGBT in a stable manner. Display of the DC/DC converter output depends on the IGBT's changes in the threshold voltage and PWM-IC's pulse width. The simulation was conducted by PSIM software, and the hardware of the DC/DC converter was also implemented. It is necessary to study the fact that the output voltage depends on the duty rate of D, and to compare the output of experimental result with the theory and the simulation.

• Biomedical Science Letters
• /
• v.15 no.3
• /
• pp.241-247
• /
• 2009

Wound healing is a complex and highly organized biological response to injury that results in the loss of tissue integrity. Our particular interest was propolis, traditional used as an antimicrobial and an anti-inflammatory agent. The purpose of this study was to see the effects of propolis on healing of the laser induced wounds and the level of collagen formation. 808 nm laser (20 J) was irradiated on the back of rats. Irradiated wounds were divided into gel control and 6 experimental groups (3 and 5% of different three kinds of propolis). Gel type of propolis (supplied by Seoul Propolis Co., Daejeon, Korea) in water based were applied on the laser wound once daily for 14 days. One fourth of rats were sacrificed on $3^{rd}$, $7^{th}$, $10^{th}$, and $14^{th}$ day and each wound was evaluated for degree of wound healing and the level of collagen formation. Healing of wound was evaluated by measuring and comparing the width and depth of the wounds. The levels of collagen were increased in 3 and 5% gel groups comparing to control on $3^{rd}$ day and the collagen level were increased more on $7^{th}$ day. Wounds of the experimental groups showed better healing in width comparing to the healing of the control. The results of this study demonstrated that propolis accelerated healing of wounds induced by laser irradiation and good collagen formation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.10
• /
• pp.1636-1647
• /
• 1997

As most of today's automatic transmissions in passenger car adopt a electro-hydraulic control system, the role of electronically controlled solenoid valves occupies an important position and it is essential to predict solenoid transient characteristics in order to design and evaluate the performance of the hydraulic control system. However, in general, both the magnetic and electrical parameters f the solenoid system are hardly known and it is not easy to model this section with moderate complexity although mechanical system could be developed using the classical second order system. This paper presents a dynamic modelling technique of a solenoid valve, that is controlled by pulse width modulation for an automatic transmission, in terms of system identification theory. In nonlinear computer simulation, it is shown that the identified systems which produce magnetic force to input duty cycle for various excitation signals predict the static and dynamic performance very well near the operating point and in experiment conducted to confirm the validity of identification theory for PWM solenoid valve, we find that there is a good agreement between the experimental data and simulation result. Hence, this model can be utilized in the development of pressure control system with PWM solenoid valve.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.6
• /
• pp.1117-1122
• /
• 2009

In this work, temperature sensor and control circuit for measuring temperature are proposed. The proposed circuit can be fabricated without additional CMOS fabrication process and the output of proposed circuit is digital value. The supply voltage is 5volts and the circuit is designed by using 0.5${\mu}m$ CMOS process. The circuit for measuring temperature consists of PWM control circuit, VCO, counter and register. consisted The frequency of PWM control circuit is 23kHz and the frequency of VCO is 416kHz, 1MHz and 2MHz, respectively. The circuit operation is analyzed by using SPICE.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.675-684
• /
• 2016

This paper presents a new stand-alone wind-based induction generator system with constant frequency and adjustable output voltage. The proposed generator consists of a six-phase cage-rotor induction machine with two separate three-phase balanced stator windings and a three-phase space vector pulse width modulation inverter that operates as a static synchronous compensator (STATCOM). The first stator winding is fed by the STATCOM and used to excite the machine while the second stator winding is connected to the generator external load. The main frequency of the STATCOM is determined to be constant and equal to the load-requested frequency. The generator output frequency is independent of the load power demand and its prime mover speed because the frequency of the induced emf in the second stator winding is the same as this constant frequency. A sliding mode control (SMC) is developed to regulate the generator output voltage. A second SMC is used to force the zero active power exchanged between the machine and the STATCOM. Some simulation and experimental results are presented to prove the validity and effectiveness of the proposed generator system.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1725-1734
• /
• 2016

This paper presents a novel seven-level (7L) voltage source converter for high-power medium-voltage applications. The proposed topology is an H-bridge connection of two nested neutral-point clamped (NNPC) converters and is referred to as an HNNPC converter. This converter exhibits advantageous features, such as operating over a wide range of output voltages, particularly for 10-15 kV applications, without the need to connect power semiconductors in series; high-quality output voltage; and fewer components relative to other classic seven-level topologies. A novel sinusoidal pulse width modulation technique is also developed for the proposed 7L-HNNPC converter to control flying capacitor voltages. One of the main features of the control strategy is the independent application of control to each arm of the converter to significantly reduce the complexity of the controller. The performance of the proposed converter is studied under different operating conditions via MATLAB/Simulink simulation, and its feasibility is evaluated experimentally on a scaled-down prototype converter.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.2
• /
• pp.137-146
• /
• 2016

An increase in EGR rate can reduce NOx emissions. On the other hand, an excessive EGR rate is a major cause of incomplete combustion. Precise position control of the EGR valve that is optimized for the operating conditions of the engine should be supported to meet the strict emission regulations. Accordingly, this study performed mathematical modeling and control theory for characteristic analysis of an EGR valve motor. Because it is a step for controlling the position of the EGR valve motor using the Microchip development tool, this study analyzed the characteristics of the motor for each opening and closing section according to the input value of the duty ratio of PWM (Pulse Width Modulation).

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.10
• /
• pp.23-28
• /
• 2010

Resistance trimming and cutting processes of printed circuit board by making use of high power UV laser with nano-second pulse width have been proposed and investigated experimentally. Also laser-based application system with high flexibility and complex has been designed and adopted power controller, auto beam size control, auto-focusing and control program developed for ourselves. The function of each module shows that they can be reliable for industrial equipments. Resistance trimming method used a plunge and double cut process with $20{\mu}m$ spot size beam. Results show that double cut process is more effective to control resistance trimming in precision than plunge cut process.