• Corrosion Science and Technology
• /
• v.23 no.3
• /
• pp.228-234
• /
• 2024

Zinc wiping is a phenomenon used to control zinc-coating thickness on steel substrate during hot dip galvanizing by equipment called air knife. Uniformity of zinc coating weight in length and width profile along with surface quality are most critical quality parameters of galvanized steel. Deviation from tolerance level of coating thickness causes issues like overcoating (excess consumption of costly zinc) or undercoating leading to rejections due to non-compliance of customer requirement. Main contributor of deviation from target coating weight is dynamic change in air knives equipment setup when thickness, width, and type of substrate changes. Additionally, cold coating measurement gauge measure coating weight after solidification but are installed down the line from air knife resulting in delayed feedback. This study presents a coating weight control model (Galvantage) predicting critical air knife parameters air pressure, knife distance from strip and line speed for coating control. A reverse engineering approach is adopted to design a predictive, prescriptive, and descriptive model recommending air knife setups that estimate air knife distance and expected coating weight in real time. Implementation of this model eliminates feedback lag experienced due to location of coating gauge and achieving setup without trial-error by operator.

• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.133-135
• /
• 2007

This research presented the new zero-current switching pulse width modulation SEPP(Single Ended Push-Pull)high frequency inverter for solving the problem of the zero-current SEPP high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the zero-current switching pulse width modulation SEPP high frequency inverter. The inverter circuit which is attempted by on-off operation of a switch has the reduction effect of the power loss due to a soft switching and a high frequency switching. And it confirmed that the power regulation is possible continuously from 0.25[kW] until 2.84[kW] in the case the duty rate(D) changes from 0.08 to 0.3 under zero-current switching operating by a dissymmetry pulse width modulating control and the power conversion efficiency comes true the efficiency of 95[%]. Due to the result above, the ZCS PWM SEPP high frequency inverter will be effective as sources of an induction heating apparatus.

• Proceedings of the KIEE Conference
• /
• 2007.11c
• /
• pp.119-124
• /
• 2007

This research presented the new zero-current switching pulse width modulation SEPP(Single Ended Push-Pull)high frequency inverter for solving the problem of the zero-current SEPP high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the zero-current switching pulse width modulation SEPP high frequency inverter. The inverter circuit which is attempted by on-off operation of a switch has the reduction effect of the power loss due to a soft switching and a high frequency switching. And it confirmed that the power regulation is possible continuously from 0.25[kW] until 2.84[kW] in the case the duty rate(D) changes from 0.08 to 0.3 under zero-current switching operating by a dissymmetry pulse width modulating control and the power conversion efficiency comes true the efficiency of 95[%]. Due to the result above, the ZCS PWM SEPP high frequency inverter will be effective as sources of an induction heating apparatus.

• Journal of Welding and Joining
• /
• v.13 no.4
• /
• pp.122-131
• /
• 1995

An automatic welding equipment for thick plates requires the capability of the seam tracking of the weld line which often includes misalignment of the workpiece and variation of groove width. In this study, an automatic welding equipment and control algorithms based on the arc sensor were proposed for the GMA welding of thick plates which had misalignment and gap variation. The developed system being constituted with 5 axis can be automatically controlled by computer and also automnatically set the welding conditions such as welding current, and voltage. The proposed algorithms for the seam tracking in multi-pass welding of the thick plates were constituted as follows : the detection of weaving-end point for findng the variation of groove width, the control of welding velocity for acquiring a constant thickness deposition of weld metal, and the calculation of groove width and height of an arbitrary pass in the multi-pass weld. As results of the application of the system, it was revealed that the system had a good capability in seam tracking and made an excellent weld quality in V groove butt joint.

• The Korean Journal of Ecology
• /
• v.6 no.2
• /
• pp.106-113
• /
• 1983

The growth of Korean axolotl., Hynobius leechii, was analyzed in natural water as control group and in six copper ion groups contaminated by 0.1, 0.2, 0.3, 0.4, 0.5, 0.6 ppm of copper ion. The copper ion checks the growth of the axolotl. The axolotl was not survived during 30 days in the copper ion of 0.3ppm, and, in the 0.4ppm the axolotl was not survived during 10 days after hatch. The growth of head width and body length show a convexing increase pattern, while that of hind leg shows a concaving increase pattern. The copper ion checks the development of hind leg. In the growth quantity of head width, body length and hid leg, that of natural water show the most rapid increase pattern, and copper ion groups of 0.1, 0.2, 0.3ppm follow in that order. The coefficient of relative growth($\alpha$) of control group is the greater value, and the copper ion groups of 0.1, 0.2, 0.3ppm follow in that order. The contaminated groups show the negative allometry in the relative growth of the containated groups to the natural water. Body length shows positive allometry, while hind leg shows negative allometry in the relative growth to head width.

• Journal of Bio-Environment Control
• /
• v.3 no.1
• /
• pp.52-57
• /
• 1994

The external qualities of cherry tomato fruits(Lycopersicon esculentum) grown in circulating deep flow hydroponic culture were non - destructively estimated in 1992 under warm climate conditions and evaluated in 1993-1994 under cool season. The fruit size of ‘Minicarol’ was by far the smallest compared to ‘Chelseamini’ and ‘Popo’. There were high correlations between external qualities of fruits-lengthwise growth harmonized with widthwise growth. The volume and/or weight of fruit could be non -destructively estimated by length and width of fruit. Volume=0.071$\times$ (length+width)$^3$＋0.451, Fresh weight=0.072$\times$ (length+width)$^3$＋0.542. These models were accurately evaluated by fruits harvested in 1994.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.241-243
• /
• 2008

This research presented the new zero-current switching pulse width modulation SEPP(Single Ended Push-Full)high frequency inverter for solving the problem of the zero-current SEPP high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the zero-current switching pulse width modulation SEPP high frequency inverter. The inverter circuit which is attempted by on-off operation of a switch has the reduction effect of the power loss due to a soft switching and a high frequency switching. And it confirmed that the power regulation is possible continuously from 0.25[kW] until 2.84[kW] in the case the duty rate(D) changes from 0.08 to 0.3 under zero-current switching operating by a dissymmetry pulse width modulating control and the power conversion efficiency comes true the efficiency of 95[%]. Due to the result above, the ZCS PWM SEPP high frequency inverter will be effective as sources of an induction heating apparatus.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.4
• /
• pp.253-265
• /
• 2016

We propose an obstacle classification method using multi-decision factors and decision sections based on Single 2D LiDAR. The existing obstacle classification method based on single 2D LiDAR has two specific advantages: accuracy and decreased calculation time. However, it was difficult to classify obstacle type, and therefore accurate path planning was not possible. To overcome this problem, a method of classifying obstacle type based on width data was proposed. However, width data was not sufficient to enable accurate obstacle classification. The proposed algorithm of this paper involves the comparison between decision factor and decision section to classify obstacle type. Decision factor and decision section was determined using width, standard deviation of distance, average normalized intensity, and standard deviation of normalized intensity data. Experiments using a real autonomous vehicle in a real environment showed that calculation time decreased in comparison with 2D LiDAR-based method, thus demonstrating the possibility of obstacle type classification using single 2D LiDAR.

• Smart Media Journal
• /
• v.8 no.1
• /
• pp.51-58
• /
• 2019

This paper describes a gesture application to controlling the special effects of physical devices for 4D contents using the PWM (Pulse Width Modulation) method. The user operation recognized by the infrared sensor is interpreted as a command for 3D content control, several of which manipulate the device that generates the special effect to display the physical stimulus to the user. With the content controlled under the NUI (Natural User Interface) technique, the user can be directly put into an immersion experience, which leads to provision of the higher degree of interest and attention. In order to measure the efficiency of the proposed method, we implemented a PWM-based real-time linear control system that manages the parameters of the motion recognition and animation controller using the infrared sensor and transmits the event.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2200-2203
• /
• 1997

This paper presents a model for p voltage controlled pulse width modulator (VCPWM), which can be used in any phase controlled converter having either manual or microprocessor based control. The circuit uses only one 555 timer, an OpAmp, some resistors, and capacitors. Although a large varieties of such circuits are available in the literature, this model is very simple with low cost and high performance.