• International Journal of Concrete Structures and Materials
• /
• v.10 no.3
• /
• pp.393-406
• /
• 2016

Axially loaded reinforced concrete columns are hardly exist in practice due to the development of some bending moments. These moments could be produced by gravity loads or the lateral loads. First, the current paper presents a detailed analysis on the overall structural behavior of 15 eccentrically loaded columns as well as one concentrically loaded control one. Columns bent in either single curvature or double curvature modes are tested experimentally up to failure under the effect of different end eccentricities combinations. Three end eccentricities ratio were studied, namely, 0.1b, 0.3b and 0.5b, where b is the column width. Second, an expression correlated the decay in the normalized axial capacity of the column and the acting end eccentricities was developed based on the experimental results and then verified against the available formula. Third, based on the equivalent column concept, the equivalent pin-ended columns were obtained for columns bent in either single or double curvature modes. And then, the effect of end eccentricity ratio was correlated to the equivalent column length. Finally, a simplified design procedure was proposed for eccentrically loaded braced column by transferring it to an equivalent axially loaded pin-ended slender column. The results of the proposed design procedure showed comparable results against the results of the ACI 318-14 code.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.5
• /
• pp.60-70
• /
• 1989

In this paper, a new HTF(Harmonic torque function) which takes into account the phasor of harmonic current, and which represents torque ripple content of induction motor is proposed. Through experiments and computer simulations using direct-quadrature two axis model, the proposed HTF is proved to be valid. Applying this function, six-step, SPWM and TPWM pulse-amplitude-width-controlled inverters are evaluated and compared with each other. A good control strategy for PAWM inverters was chosen from the results. It turns out that TPWM is superior to SPWM in torqur ripple content and output voltage amplitude of fundamental wave and six-step is better than PWM when CR is 9.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.5
• /
• pp.85-93
• /
• 1994

We have studied the effect of channel and/or spacing chirpings on the near field and near field intensity patterns, modal gains and radiation angles of 6 supermodes in the index-guided laser arrays with 6 channels, on the basis of the coupled mode theory. The spacings between channels can be indenpendent parameters for control of the radiation angle. It is found that an asymmetrically v channel-chirped array has both a smaller radiation angle and better supermode discrimination characteristics than a uniform array. Comparing two approaches for enhancing modal stability in point of supermode discrimination characteristics, approach I which increases the coupling cofficient between the outer-most waveguides at each end of an otherwise uniform array, has superior discrimination characteristics to the approach II which increases the propagation constant for the end elements with the same coupling between neighbor elements. Approach III which has a narrower spacing between the outer-most waveguides at one end and a wider channel width of the outer-most waveguide at another end, gets a narrower radiation angle than the approach I and good supermode discrimination characteristics by applying optimized gain profiles.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.4
• /
• pp.41-49
• /
• 1989

Following the previous paper, the results of test are further presented. As partially prestressed concrete members permit cracks under the service state, deflection and crack control of partially prestressed concrete members is more important than that of reinforced or fully prestressed concrete members. By the test results of load-deflection relation, it can be shown that prestressing ratio significantly affects the behavior of partially prestressed concrete beams. Deflection prediction formula of some codes are tried, and test results are compared with various fomulae of crack spacing and crack width.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.3 s.234
• /
• pp.418-424
• /
• 2005

We present the design, fabrication and experimental results of 4-bit digital microinjectors, whose ejected droplet volumes are adjusted by the digital operation of a 4-bit microheater array. We design the reference microinjectors as well as its comparative test structures. In the fabrication process, we use a five-mask micromachining process and the total chip size of the fabricated microinjector is $7,640{\mu}m{\times}5,260{\mu}m.$ We measure the ejected droplet volumes and velocities, which are adjusted from $12.1{\pm}1.0~55.6{\pm}14.7pl\;and\;2.3{\pm}0.1~15.7{\pm}0.8m/s.$ respectively, depending on the 15 possible combinations of 4-bit microheater array. We also experimentally characterize the effect of geometric variation including the microheater size, inter-microheater gap, microchannel width and sequential operation of microheater array on the ejected droplet volume and velocity. Among these parameters, we find that the microheater size is the most dominant parameter affected to the ejected droplet volumes and velocities. Thus, the present microinjector has a potential for application to the high-resolution inkjet printers with multiple gray levels or high-precision fluid injectors with variable volume control.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.3
• /
• pp.47-52
• /
• 2007

LMTT (Linear Motor based Transfer Technology), which is a new type transfer system used in the maritime container terminal for the port automation, is driven by PM LSM (Permanent Magnetic Linear Synchronous Motor), and largely consists of a controller, shuttle car, and rail. The shuttle car is divided into the frame part, the driving part, and wheels. Because the shuttle car is supported by four wheels in opposition to have five times length for the width of it, a larger deflection than other transfer system using the linear motor occurs. This deflection changes the gap between the mover and the stator, and then brings on an ununiform thrust force. So in this study, we dealt with the structural design for the mover of the shuttle car to generate the uniform thrust force for the efficient control of it. For the investigation, the thickness for each beam of the mover was adopted as design variables, the weight of the mover as objective function, and stress and deflection of the mover as constraint condition.

• 한국전산유체공학회:학술대회논문집
• /
• 2006.10a
• /
• pp.181-184
• /
• 2006

High-speed flight vehicle have various cavities. The supersonic cavity flow is complicated due to vortices, flow separation and reattachment, shock and expansion waves. The general cavity flow phenomena include the formation and dissipation of vortices, which induce oscillation and noise. The oscillation and noise greatly affect flow control, chemical reaction, and heat transfer processes. The supersonic cavity' flow with high Reynolds number is characterized by the pressure oscillation due to turbulent shear layer, cavity geometry, and resonance phenomenon based on external flow conditions, The resonance phenomena can damage the structures around the cavity and negatively affect aerodynamic performance and stability. In the present study, we performed numerical analysis of cavities by applying the unsteady, compressible three dimensional Reynolds-Averaged Navier-Stokes(RANS) equations with the ${\kappa}-{\omega}$ turbulence model. The cavity model used for numerical calculation had a depth(D) of 15mm cavity aspect ratio(L/D) of 3, width to spanwise ratio(W/D) of 1.0 to 5.0. Based on the PSD(Power Spectral Density) and CSD(Cross Spectral Density) analysis of the pressure variation, the dominant frequency was analyized and compared with the results of Rossiter's Eq.

• Journal of computational fluids engineering
• /
• v.11 no.4 s.35
• /
• pp.62-66
• /
• 2006

High-speed flight vehicle have various cavities. The supersonic cavity flow is complicated due to vortices, flow separation, reattachment, shock waves and expansion waves. The general cavity flow phenomena includes the formation and dissipation of vortices, which induce oscillation and noise. The oscillation and noise greatly affect flow control, chemical reaction, and heat transfer processes. The supersonic cavity flow with high Reynolds number is characterized by the pressure oscillation due to turbulent shear layer, cavity geometry, and resonance phenomenon based on external flow conditions. The resonance phenomena can damage the structures around the cavity and negatively affect aerodynamic performance and stability. In the present study, we performed numerical analysis of cavities by applying the unsteady, compressible three dimensional Reynolds-Averaged Navier-Stokes(RANS) equations with the ${\kappa}-{\omega}$ turbulence model. The cavity model used for numerical calculation had a depth(D) of 15mm cavity aspect ratio (L/D) of 3, width to spanwise ratio(W/D) of 1.0 to 5.0. Based on the PSD(Power Spectral Density) and CSD(Cross Spectral Density) analysis of the pressure variation, the dominant frequency was analyzed and compared with the results of Rossiter's Eq.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.321-324
• /
• 2002

Hydraulic valve control the pressure and the How of fluid by the hydraulic oil transfered from pump but the ER fluid consists of solid particles of micrometer in size and insulating oil so in the general hydraulic valve. We invented ER-Valve using ER fluid as working fluid. The ER fluid, working fluid of ER-Valve is a functional fluid to represent the feature of fluid according to strength of electric field. In this research we made our own 4 types of plate type ER-Valve which has same surface but different width and length and then we conducted performance test. We measured flow rate and pressure drop of fluid which is flowing in the ER-Valve according to the electric field strength to conduct this test. We modeling ER-Valve relating to ER-Valve system and yield shear stress according to the strength of electric field. We used the pressure drop according to the strength of electric field by differential pressure gauge in the our own made ER-Valve. This test reviewed experimental the special changes of ER-Fluid in the steady flow condition.

• The Journal of Korean Physical Therapy
• /
• v.29 no.3
• /
• pp.135-141
• /
• 2017

Purpose: This study was to identify the anticipatory postural adjustment (APA) mechanism which is represented by the onset time of trunk muscles and the displacement of the center of pressure (COP) according to the different base of support (BOS) during upper extremity movement. Methods: Thirty healthy subjects (14 males, 16 females) participated in this study. The movement was performed for 10 trials during each of various BOS (shoulder - width double leg stance, narrow base double leg stance, tandem stance, non-dominant single leg stance) at the 1.2 Hz frequency. Electromyography was used to measure muscle onset time and biorescue was used to measure characteristics of the displacement of COP. Surface bipolar electrodes were applied over the right deltoid anterior, right latissimus dorsi, both rectus abdominis, both internal oblique and both erector spinae. The data were analyzed by repeated one-way ANOVA and Duncan's post hoc test. Results: The study has revealed following. There were significant differences with muscle onset time in each BOS (p<0.01). There were significant differences in characteristics of the COP in each BOS (p<0.01). Conclusion: The study found that the more narrowed the basis requires the more rapid anticipatory postural control in contralateral postural muscle when the upper extremity movement is performed.