• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.101-101
• /
• 2000

MSC(Multispectral Camera), which will be a unique payload on KOMPSAT-II, is designed to collect panchromatic and multi-spectral imagery with a ground sample distance of 1m and a swath width of 15km at 685km altitude in sun-synchronous orbit. The instrument is designed to have an orbit operation duty cycle of 20% over the mission life time of 3 years. MSC electronics consists of three main subsystems; PMU(Payload Management Unit), CEU(Camera Electronics Unit) and PDTS(Payload Data Transmission Subsystem). PMU performs all the interface between spacecraft and MSC, and manages all the other subsystems by sending commands to them and receiving telemetry from them with software protocol through RS-422 interface. CEU controls FPA(Focal Plane Assembly) which contains TDI(Timc Delay Integration) CCD(Charge Coupled Device) and its clock drivers. PMU provides a Master Clock to synchronize panchromatic and multispectral camera. PDTS performs compression, storage and encryption of image data and transmits them to the ground station through x-band.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.374-374
• /
• 2000

In this paper, we developed an ANFIS controller through ES algorithm for disturbances rejection in Hot Rolling. The looper of a Hot Rolling is installed between each pair of stands and plays key roles to enhance the product quality of the strip by controlling the tension and the width of the strip. At the same time, the AGC on top of the Mill produces a strip with the desired thickness through pressing its Mill. Between both, however, interactions are caused by coupling effects among strip tension, looper angle and strip thickness. In addition, in case disturbances, it is more difficult to keep strip quantities desirable. So we present an ANFIS controller through ES algorithm which is able to identify fuzzy rule with input/output data and update itself through output errors.

• Transactions of Materials Processing
• /
• v.18 no.3
• /
• pp.262-267
• /
• 2009

Selective laser sintering is a kind of rapid prototyping process whereby a three-dimensional part is built layer wise by laser scanning the powder. This process is highly influenced by powder and laser parameters such as laser power, scan rate, fill spacing and layer thickness. Therefore a study on fabricating Fe-Ni-Cr powder by selective laser sintering has been performed. In this study, fabrication was performed by experimental facilities consisting of a 200W fiber laser which can be focused to 0.08mm and atmospheric chamber which can control atmospheric pressure with argon. With power increase or energy density decrease, line width was decreased and line surface quality was improved with energy density increase. Surface quality of quadrangle structure was improved with fill spacing optimization.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.553-558
• /
• 1994

In this paper, we present a new approach for the automation of deburring process. An algorithm for teaching skills of a human expert to a robot manipulator is developed. This approach makes use of TSK fuzzy model that can express a highly nonlinear functional relation with small number of rules. Burr features such as height, width, area, cutting area are extracted from image processing by use of the vision system. Cutting depth, repeative number and normal cutting force are chosen as control signals representing actions of the human expert. It is verified that our processed fuzzy model can accurately express the skills of human experts for the deburring process.

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.2
• /
• pp.103-108
• /
• 1999

The paper describes a implementation of space vector pulse-width modulation voltage source inverter and interfacing of DSP using field programmable gate array(FPGA) for a induction motor vector control system. The implemented chip is included logic circuits for SVPWM, dead time compensation and speed detection using Quick Logic, QLl6X24B. The maximum operating frequency and delay time can be set to 110MHz and 6 nsec. The designed Application Specific Integrated Circuit(ASIC) for SVPWM can be incorporated with a digital signal processing to provide a simple and effective solution for high performance induction motor drives with a voltage source inverter. Simulation and implementation results are shown to verify the usefulness of ASIC in a motor drive system and power electronics applications.

• Proceedings of the Korean Society of Fisheries Technology Conference
• /
• 2003.05a
• /
• pp.351-352
• /
• 2003

The demilitarized zone (DMZ) covered about 1, 528 $\textrm{km}^2$ (length, 248 km; width, about 4 km), and the civilian control line (CCL) was established around the DMZ after the Korean War. The international organizations (UNESCO and IUCN) showed a continued interests on the biodiversity of the DMZ area, because of relatively well preserved environment and lack of anthropogenic disturbances other than agricultural practice (KFRI, 2000). (omitted)

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2008.04a
• /
• pp.218-221
• /
• 2008

The real scale fire suppression test inside a road tunnel were carried out for water spray systems. The dimension of the tunnel is 7.5m in height and 11.6m in width. 3 different water spray nozzle systems with low operating pressure less than 3.5 bar were used in the experiment. Two types of fires were tested. One is a $1.4m^2$ heptane pool fire and the other is a 2000CC passenger car fire. From the experiment, the spray densities of tested systems were about $6.0\;l/min/m^2$ which is currunt domestic guideline. Although all the systems cannot extinguish the tested fires, it was found that they can reduce the tunnel temperature and have a capability to control and suppress the tested fire.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.04a
• /
• pp.310-313
• /
• 2003

Removal of phenanthrene by electrokinetic method combined with Fenton-like process was studied in a model system. The scale of reactor was 120 cm in length, 10 cm in width, and 50 cm in height. Sand was selected as a model soil. Bentonite was filled in the space between reservoir and contaminated soil to control the flow rate of water. When constant voltage of 100 V was applied to this system, current varied from 1000 mA to 290 mA for 28 days. pH of anode and cathode reservoirs became to 2 and 13, respectively. Removal efficiency of phenanthrene was more than 60 %.

• Tribology and Lubricants
• /
• v.18 no.2
• /
• pp.109-116
• /
• 2002

phase lubrication can be used as an alterative lubrication method to overcome the demerits of liquid and solid lubrications. In this work, the tribological characteristics of metals are investigated under vapor phase lubrication. It was found that the friction coefficient and wear volume can be controlled efficiently by the amount of vapor phase lubricant delivered to the sliding interface. The friction coefficient could be reduced to about 0.1 under vapor lubrication. Also, depending on the amount of vapor lubrication delivered to the system, the width of the wear track could be varied between 50 to 250 Um. It is shown that vapor phase lubrication mechanism is very effective to control the friction and wear phenomena without the use of excessive oil.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.363-365
• /
• 2007

Titanium and its alloys have excellent corrosion resistance, high strength to weight ratios and high temperature creep properties, which make them using many various fields of application. Responding to these needs, welding processes for titanium are also being used including TIG, MIG, resistance welding, plasma arc welding, diffusion welding, electron beam welding and laser welding. In this study, It is possible to get sound beads without humping bead and spatter with the decrease of peak power according to increase of pulse width and change of welding speed for heat input control at pulsed Nd:YAG laser welding of titanium plates for Lap welding.