• Wind and Structures
• /
• v.37 no.1
• /
• pp.15-23
• /
• 2023

The wake behavior of extended flat plate and serration in the trailing edge of S809 airfoil is presented in this experimental study using wind tunnel testing. The clustering of wind turbines in wind parks has recently been a pressing issue, due to the expected increase in power output and deciding the number of wind turbines to be installed. One of the prominent factors which influence the performance of the subsequent wind turbines is the downstream wake characteristics. A series of wind tunnel investigations were performed to assess the downstream near wake characteristics of the S809 airfoil at various angles of attack corresponding to the Reynolds Number Re = 2.02 × 105. These experimental results revealed the complex nature of the downstream near wake characteristics featuring substantial asymmetry arising out of the incoherent flow separations prevailing over the suction and the pressure sides of the airfoil. Based on the experimental results, it is found that the wake width and the downstream velocity ratio decrease with an increase in the angle of attack. Nonetheless, the dissipation length and downstream velocity ratio increases proportionally in the downstream direction. Additionally, attempts were made to understand the physical nature of the near wake characteristics at 1C, 2C, 3C and 4C downstream locations.

• Journal of Hydrogen and New Energy
• /
• v.34 no.6
• /
• pp.734-740
• /
• 2023

Hydrogen emphasis on safety management due to its high potential for accidents from wide explosive limits and low ignition energy. To prevent accidents, appropriate explosion-proof electrical equipment with installed to safe management of ignition sources. However, designing all facilities with explosion-proof structures can significantly increase costs and impose limitations. In this study, we optimize the barrier to effectively control the initial momentum in case of hydrogen release and form the control room as a non-hazardous area. We employed response surface method (RSM), the barrier distance, width and height of the barrier were set as variables. The Box-Behnken design method the selection of 15 cases, and FLACS assessed the presence of hazardous area. Analysis of variance (ANOVA) analysis resulting in an optimized barrier area. Through this methodology, the workplace can optimize the barrier according to the actual workplace conditions and classify reasonable hazardous area, which is believed to secure safety in hydrogen facilities and minimize economic burden.

• Journal of Sericultural and Entomological Science
• /
• v.18 no.2
• /
• pp.65-78
• /
• 1976

The mulberry small weevil, Baris deplanata ROELOFS, has highly infested mulberry trees in Korea. As the damage caused by the mulberry small weevil in mulberry fields has been increased over the country since 1969, the authors has carried out a series of biological and controlling studies on the pest from 1971 to 1972. The results obtained are summarized as follows. 1. The adult weevil is elongate oval in shape with black in color and the probocis is long as usual in curculionidae. The size of adult female is 3.30${\pm}$0.04mm in length, 1.47${\pm}$0.04mm in width, and the length of proboscis is 1.25${\pm}$0.014mm, while adult male is 3.28${\pm}$0.06mm in length, 1.40${\pm}$0.04mm in width, and the length of proboscis is 1.30${\pm}$0.02mm. The antenna is geniculate consisting of 12 segments. The terminal sternite of the abdomen has a pointed tip in male but not in female. 2. The egg is long oval in shape, milky white in color, 0.51${\pm}$0.05mm in length and 0.32${\pm}$0.02mm in width. 3. The mature larva is cylindrical and light yellowow in color except the head of dark brown, and legless, 3.88${\pm}$0.06mm in length, 1.40${\pm}$0.02mm width, each segment bearing many wrinkless and short setae. 4. The pupa is long oval, milky white and exarate, 3.53${\pm}$0.09 in length, 1.40${\pm}$0.03mm in width. 5. Majority of the species has one generation through a year and overwinters as adult in xylem of withered branch and come out again from late April to early May in next year. But some of the female oviposit in the same year and the offsprings overwinter as larva (0.4%) or pupa (0.1%) 6. The eggs are mostly laid under the cork layer of withered branch and the number of eggs deposited by an adult female is 73.44${\pm}$8.74, the average egg-laying period is 33.88${\pm}$6.04 days. The incubation period is 11.69${\pm}$0.39 days, the larval period 45.04${\pm}$1.63 and the pupal period 11.05${\pm}$0.49 days. The period of adult's activity is 46.7${\pm}$5.90 days. 7. The larvae feed on the cambium under the bark and adults feed on the winter bud, the latent bud, the leaf stalk and the base of newly shoot. 8. An active period of adults was observed during the period of 4 months from April to July. However, the peak of adult-density occurred in the early May (in the fields of spring-prunning) and early to middle June(in the fields of summer-prunning). 9. There is a positive correlation between the density of larvae and diameter and length of the branches. 10. The pattern of distributions of the adult of mulberry small weevil is negative binomial distribution. 11. The chalcid fly was disclosed to be a natural enemy which was parasite on the larvae of mulberry small weevil and its parasitic ratio was 11.9%. 12. Phosvel D, Malix D, Salithion EC, DDVP EC, and Phosvel EC were effective for the control of adults and Satchukoto-S EC, and Salithio EC were effective for the control of larvae.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1923-1930
• /
• 2004

This paper presents digital microflow controllers(DMFC), where a fluidic digital-to-analog converter(DAC) is used to achieve high-linearity, fine-level flow control for applications to precision biomedical dosing systems. The fluidic DAC, composed of binary-weighted flow resistance, controls the flow-rate based on the ratio of the flow resistance to achieve high-precision flow-rate control. The binary-weighted flow resistance has been specified by a serial or a parallel connection of an identical flow resistor to improve the linearity of the flow-rate control, thereby making the flow-resistance ratio insensitive to the size uncertainty in flow resistors due to micromachining errors. We have designed and fabricated three different types of 4-digit DMFC: Prototype S and P are composed of the serial and the parallel combinations of an identical flow resistor, while Prototype V is based on the width-varied flow resistors. In the experimental study, we perform a static test for DMFC at the forward and backward flow conditions as well as a dynamic tests at pulsating flow conditions. The fabricated DMFC shows the nonlinearity of 5.0% and the flow-rate levels of 16(2$^{N}$) for the digital control of 4(N) valves. Among the 4-digit DMFC fabricated with micromachining errors, Prototypes S and P show 27.2% and 27.6% of the flow-rate deviation measured from Prototype V, respectively; thus verifying that Prototypes S and P are less sensitive to the micromachining error than Prototype V.V.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.1
• /
• pp.92-97
• /
• 2007

This paper performed the basic study for developing the Photodynamic Therapy Equipment for medical treatment. We developed the equipment palpating cell proliferation using a high brightness LED. This equipment was fabricated using a micro-controller and a high brightness LED, and designed to enable us to control light irradiation time, intensity, frequency and so on. Especially, to control the light irradiation frequency, FPGA was used, and to control the change of output value, TLC5941 was used. Control stage is divided into 30 levels by program. Consequently, the current value could be controlled by the change of level in Continue Wave(CW) and Pulse Width Modulation(PWM), and the output of a high brightness LED could be controlled stage by stage. And then, each experiment was performed to irradiation group and non-irradiation group for both Rat bone marrow and Rat tissue cells. MTT assay method was chosen to verify the cell increase of two groups and the effect of irradiation on cell proliferation was examined by measuring 590 nm transmittance of ELISA reader. As a result, the cell increase of Rat bone marrow and tissue cells was verified in irradiation group as compared to non-irradiation group. The fact that specific wavelength irradiation has an effect on cell vitality and proliferation is known through this study.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.27 no.3
• /
• pp.238-247
• /
• 2005

The placement of different graft materials and/or the use of occlusive membranes to cover the extraction socket entrance are techniques aimed at reducing alveolar ridge resorption and enhancing bone formation. However, in spite of its clinical advantage, the use of graft materials in fresh extraction socket has been questioned because particles of the grafted material have been found in alveolar sockets with fibrous union. The purposes of this study were to evaluate whether alveolar ridge resorption following tooth extraction could be reduced and bone formation could be enhanced by the application of absorbable gelatin spongy or gelatin spongy soaked with platelet rich plasma(PRP) used as a space filler in clinical and radiographic aspects. Eighty patients who were scheduled for extraction of both third molars were participated and carried out by one experienced surgeon. Following extraction of teeth, one extracted socket were treated with gelatin spongy as an experimental group A and the other were treated with gelatin spongy and PRP as an experimental group B. The routine extracted socket were healed without any treatment as a control group. From the period of extraction to 12 weeks postoperatively, we examined the clinical course and radiographic evaluation on socket at regular interval. Both experimental groups showed faster wound healing process than control clinically. Vertical gingival height of the extraction socket were less changed statistically in both experimental groups than control. The horizontal width change of the extraction socket were not significant statistically in any group. Radiographic changes of the alveolar bone height were less changed in both experimental groups and bone density were showed higher than control. There were a little difference between experimental group A and B. In conclusion, absorbable gelatin sponge and with PRP were considered as having preservation effects of extraction socket and stimulation of bone formation process after extraction.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.5
• /
• pp.354-365
• /
• 2015

This work presents an Internet of Things (IoT) system for home energy management based on a custom-designed Impulse Radio Ultra-Wideband (IR-UWB) transceiver that targets a generic and multi-standard control system. This control system enables the interoperability of heterogeneous devices: it integrates various sensor nodes based on ZigBee, EnOcean and UWB in the same middleware by utilizing an ad-hoc layer as an interface between the hardware and software. The paper presents as a first the design of the IR-UWB transceiver for a portable sensor node integrated with the middleware layer, and also describes the receiver connected to the control system. The custom-designed low-power transmitter on the sensor node is fabricated with 130 nm CMOS technology. It generates a signal with a 1.1 ns pulse width while consuming $39{\mu}W$ at 1 Mbps. The UWB sensor node with a temperature measurement capability consumes 5.31 mW, which is lower than the power level of state-of-the-art solutions for smart-home applications. The UWB hardware and software layers necessary to interface with the control system are verified in over-the-air measurements in an actual office environment. With the implementation of the presented sensor node and its integration in the energy management system, we demonstrate achievement of the broad flexibility demanded for IoT.

• Research in Plant Disease
• /
• v.10 no.4
• /
• pp.304-309
• /
• 2004

Girdling of trunk and rainproof installation over kiwifruit (Actinidia deliciosa) trees were turned out to alleviate bacterial blossom blight effectively in kiwifruit orchards. The disease was most effectively prevented by girdling of tree trunks with 20 mm width around April 10 before about 45 days of flowering stage of kiwifruit, but control efficiencies were not affected by height of girdling on trunks above the ground. Use of a transparent polyvinyl film to protect kiwifruit trees from rain was more effective than windbreak net to prevent the disease, irrespective of kinds of rainproof installation. Installation of partial rainproof vinyl cover over kiwifruit trees around March 10 before about 75 days of flowering stage of kiwifruit prevented most of the disease occurrence on kiwifruit. It is expected that girdling of tree trunks and installation of partial rainproof vinyl cover over kiwifruit trees will be practical as environmentally friendly control methods to manage bacterial blossom blight in kiwifruit orchards.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.11
• /
• pp.77-83
• /
• 2010

This paper presents the dual resonance PIFA(Planar Inverted F-Antenna) which satisfies the requirements of the 802.11n standard at both 2.4 GHz and 5 GHz frequency bands. Patch for 2.4 GHz and U-Type slot for 5 GHz were used for dual resonance, respectively. In this paper, the characteristics of an antenna were investigated by varying locations of short plate and feed point, the width of the short plate, the thickness and the location of U-Type slot. To investigate the characteristics of the PIFA, HFSS(High Frequency Structure Simulation) for the simulation was used. And the measurement results of a fabricated PIFA were compared with the simulated ones. The measurement and simulation results show that good dual resonance characteristics as the thickness of U-type slot decreases and when the location of U-type slot is far from the feed point.

• Archives of Plastic Surgery
• /
• v.32 no.4
• /
• pp.521-528
• /
• 2005

The purpose of this research is to find out the degree of cartilage regeneration by inserting the atelo-collagen scaffold obtained from dermis of a calf on cartilage defect site. Dissection underneath the perichondrium by the periosteal elevator on both side of ears of six New Zealand white rabbits were made to expose the cartilage, leaving pairs of circular holes 3, 6, 9 mm width with punches. One hole was left for a control, and on the other hole atelo-collagen scaffold of the same size was transplanted. In postoperative 1, 2, 4 weeks, the tissues were dyed. The length of long axis of neocartilage was measured through an optical microscope with a 0.1 mm graduation at original magnification, ${\times}40$. In the first and second week, both group showed no sign of cartilage regeneration. In the fourth week, regeneration on marginal portions was observed on all groups and the average values of length of long axis of neocartilage according to defect size were as follows: In the cases with 3mm defect, it was $0.85{\pm}0.30mm$ in the control group, and $1.85{\pm}0.38mm$ in the graft group; in the cases with 6 mm defect, $1.33{\pm}0.58mm$ in the control group, and $2.25{\pm}0.46mm$ in the graft group; and in the cases with 9 mm defect, $2.33{\pm}0.77mm$ in the control group, and $4.47{\pm}1.39mm$ in the graft group. This means that the collagen scaffold has an influence on the regeneration of neocartilage. But the relative ratio of the length of neocartilage to cartilage defect size was not significant in the statistics.