• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.311-315
• /
• 2006

Precision location and positioning of Asset within a network is an attractive feature with various applications, especially in indoor environments. Such a demand is met by the standard task group, IEEE 802.15.4a. Several methods, that is, pulse, chirp and chaotic communications have been proposed so far to satisfy the requirements of the standard. Among them, ultra wideband direct chaotic communications has advantageous features such as low hardware complexity, low cost, lower power consumption and flexible frequency band plan. In this paper, the feasibility of the ranging system using non-coherent chaotic transceiver is investigated by designing and implementing the system and the performance is proved by conducting location experiments in real indoor environments.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.69-73
• /
• 2008

In this paper, analytical methods for calculating the average probability of bit error of time hopping pulse position modulation ultra wideband (TH-PPM UWB) system are given. For the multi-user DS-PAM UWB system, the bipolar pulse amplitude modulation is used in order to achieve better performance. As we know, more attention is paid to the TH-PPM UWB systems recently. In this paper, we first introduce the accurate BER calculation methods of the multi-user TH-PPM UWB systems and then give the performance analysis over the ideal AWGN channel and a correlation receiver. Furthermore, we also introduce their applications in image transmission and data transmission and give the simulation results. The analytical method yields simple and exact formulas relating the performance to the system parameters.

• Korean Journal of Optics and Photonics
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2013

In this paper, we report design, fabrication and characterization of the WBRM (Wide Band Receiver Module) for LADAR (LAser Detection And Ranging) application. The WBRM has been designed and fabricated using self-made APD (Avalanche Photodiode) and TIA (Trans-impedance Amplifier). The APD and TIA chips have been integrated on 12-pin TO8 header using self-made ceramic submount and circuit. The WBRM module showed 450 ps of rise time, and corresponding 780 MHz bandwidth. Furthermore, it showed very low output noise less than 0.8 mV, and higher SNR than 15 for 150 nW of MDS(Minimum Detectable Signal). To the author's knowledge, this is the best performance of an optical receiver module for LIDAR fabricated by 200 um InGaAs APD.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.5A
• /
• pp.401-407
• /
• 2009

The multi-band (MB) ultra-wideband (UWB) communication system divides its available frequency spectrum in 3.1 to 10.6GHz into 16 sub-bands, which leads to inherent disparities between carrier frequencies of each sub-band. For instance, the highest carrier frequency is 2.65 times higher than the lowest one. Since the propagation loss is proportional to the square of the transmission frequency, the propagation loss on the sub-band having the highest carrier frequency is approximately 7 times larger than that on the sub-band having the lowest carrier frequency, which results in disparities between received signal powers on each sub-band. In this paper, we propose a novel correlation scheme for frequency hopping (FH) MB UWB communications, where the correlation time is adaptively adjusted relative to the sub-band, which reduces the disparity between the received signal energies on each sub-band. Such compensation for lower received powers on sub-bands having higher carrier frequency leads to an improvement on the total average bit error rate (BER) of the entire FH MB UWB communication system. We analyze the performance of the proposed correlation scheme in Nakagami fading channels, and it is shown that the performance gain provided by the proposed correlator is more significant as the Nakagami fading index n increases (i.e., better channel conditions).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.12
• /
• pp.42-48
• /
• 2008

Next generation wireless communication systems require RF transceivers that enable multiband/multimode operations. Polar transmitters are known as good candidates for high data rate systems such as EDGE (Enhanced Data Rates for GSM Evolution), WCDMA (Wideband Code Division Multiple Access), and WLAN (Wireless Local Area Network) because they can obtain high efficiency by using efficient switched-mode RF power amplifiers. In this paper, we investigate the performance of a simple peak windowing scheme for the OFDM (Orthogonal frequency Division Multiplexing) polar transmitter, which requires no change of a receiver structure or no additional information transmission. The approach we employed is to apply the peak windowing scheme to the amplitude modulated signals of the polar transmitter to reduce the PAPR (Peak-to-Average Power Ratio). The BER (Bit Error Rate) and EVM (Error Vector Magnitude) performances are measured for various window types and lengths. The simulation results demonstrate that the proposed algorithm mitigates out-of-band distortion introduced by clipping along with PAPR reduction.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.635-639
• /
• 2016

In the devices used in the microwave frequency band, the gain decreases as the frequency increases due to the parasitic component. To compensate for these characteristics, a linear gain equalizer with an opposite slope is needed in wideband systems, such as those used for electronic warfare. In this study, a linear gain equalizer that can be used in the 18 ~ 40GHz band is designed and fabricated. Circuit design and momentum design (optimizations) were carried out to reduce the errors between design and manufacturing. A thin film process is used to minimize the parasitic components within the implementation frequency band. A sheet resistance of 100 ohm/square was employed to minimize the wavelength variation due to the length of the thin film resistor. This linear gain equalizer is a structure that combines a quarter wavelength-resonator on a series microstrip line with a resistor. All three 1/4 wavelength short resonators were used. The fabricated linear gain equalizer has a loss of more than -5dB at 40GHz and a 6dB slope in the 18 ~ 40GHz band. By using the manufactured gain equalizer in a multi-stage connected device such as an electronic warfare receiver, the gain flatness degradation with increasing frequency can be reduced.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.706-715
• /
• 2012

Electro-optical sigma-delta modulators are the core module of digital receiver to digitize wideband radio-frequency signals directly at an antenna. Electro-optical sigma-delta modulators use a pulsed laser to oversample an input radio-frequency signals at two Mach-Zehnder Interferometer(MZI) and shape the quantization noise using a fiber-lattice accumulator. Decimation filtering is applied to the quantizer output to construct the input signal with high resolution. The jitter affects greatly on reconstructing the original input signal of modulator. This paper analyzes the performance of first order single bit electro-optical sigma-delta modulator in the time domain and the frequency domain. The performance of modulator is analyzed by using asynchronous spectral averaging of the reconstructed signal's spectrum in the frequency domain. The reference value of time jitter is presented by analyzing the performance of jitter effects. This kind of jitter value can be used as a reference value on the design of modulators.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.4 no.3
• /
• pp.183-189
• /
• 2009

In this paper, we propose RF front-end architecture using hybrid conversion method to receive broadband signal. The validity is verified by design, fabrication and experiment. The proposed RF front-end architecture due to up-conversion block improves the deficiency of performance deterioration to be generated through harmonic signal and image signal conversion in the conventional RF front-end, and improves the deficiency of the complexity that is from to adopt a multiple local oscillators for the generation of wideband LO signal in the conventional RF front-end by applying the principle that tuning bandwidth is multiplied at sub-harmonic mixer. Manufactured circuits satisfy the deduced design specification and target standard with gain above 80 dB, noise figure below 6.0 dB and IIP3 performance above -5.0 dBm for the condition of the minimum gain in RF front-end.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.15 no.6
• /
• pp.29-34
• /
• 1978

It has been investigated that the elect of an wideband FDM-FM signal upon an M-ary coherent PSK (MCPSK) signal in an intersystem radio interference environment between analog and digital systems, which had not been discussed before and had been obscure. It is assumed that PSK and FM signal are adjacently allocated in same radio frequency band. And the symbol error performance of MCPSK signal with co-channel and adjacent channel interference from an FDM-FM signal is evaluated with considering the receiver noise. The numerical results for the theoretical symbol error rates of MCPSK system in the presence of Gaussian noise and co-channel or adjacent channel interference are given in graphical forms as the function of carrier-to-noise ratio (CNR), carrier-to-interference ratio (CIR) and normalized carrier separation between the desired PSK and interfering FM signal. The objective of this research is to find some optimal conditions for coexistence of analog and digital systems in an intersystem interference environment. The results we obtained here stress a possible utilization of them for designing the frequency allocation, bandwidth and power of PSK channel in the intersystem interference from an FDM-FM signall.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.5
• /
• pp.171-180
• /
• 2003

CDMA(Code Division Multiple Access) mobile communication systems require accurate channel estimation in the receiver to compensate the fading distortions. Instantaneous channel estimates are obtained by dividing the received symbol by the transmitted symbol and then refined by filtering to reduce the estimation variance. In the channel estimation filter, the determination of the filter size is a very important task which greatly affects the estimation quality. While conventional methods usually use only velocity estimators to determine the channel estimation filter size, this paper proposes a filter size determination method for decision-directed channel estimators considering the symbol error rate and the signal-to-noise ratio in addition to the velocity of the mobile station. This paper shows that the symbol error rate and the signal-to-noise ratio are important factors for the determination of the channel estimation filter size.