• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.644-650
• /
• 2003

In this paper, we have studied characteristics of PHEMT's fabricated by two difference types of gate recess for improving performance of the device in millimeter wave applications. PHEMT's were fabricated using wide and narrow recesses. Maximum transconductance(g$_{m}$) of PHEMT's using the wide recess was 332.7 mS/mm, and that of PHEMT's using narrow recess was 504.6 mS/mm. From small signal performance measurements, cutoff frequency(f$_{T}$) and maximum stable oscillation frequency(f$_{max}$) of PHEMT's using wide recess were 113 GHz and 172 GHz, respectively. f$_{T}$ and f$_{max}$ of PHEMT using narrow recess were 101 GHz and 142 GHz, respectively. The measured data of the fabricated PHEMTs' were carefully studied and analyzed.d.tudied and analyzed.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.249-252
• /
• 2002

we have studied the characteristics of PHEMT's with gate recess etching method. The DC characterization of PHTMT fabricated with the wide single recess methods is a maximum drain current density of 319.4 ㎃/mm and a peak transconductance of 336.7 ㎳/mm. The RF measurements were obtained in the frequency range of 1~50GHz. At 50GHz, 3.69dB of 521 gain were obtained and a current gain cut-off frequency(f$_{T}$) of 113 CH and a maximum frequency of oscillation(f$_{max}$) of 172 Ghz were achieved from this device. On the other hand, a maximum drain current of 367 mA/mm, a peak transconduclancc of 504.6 mS/mm, S$_{21}$ gain of 2.94 dB, a current gain cut-off frequency(f$_{T}$) of 101 CH and a maximum frequency of oscillation(f$_{max}$) of 113 fa were achieved from the PHEMT's fabricated by the .narrow single recess methods.methods.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.57-60
• /
• 2011

The spray characteristics according to the recess length of the GCSC injector and the change of momentum flux ratio(MFR) of the gas and the liquid have been examined through high pressure cold flow test using a high pressure chamber. The liquid in this experiment was water, and the gas was nitrogen. The spray images were taken by a back-lit strobe imaging technique. Results showed that the spray was a wide hollow cone at the lower MFR(liquid velocity was fixed) and the spray became a narrow solid cone as the MFR was increased. And the injector with short recess length produced a narrow solid cone at the higher MFR.

• ETRI Journal
• /
• v.13 no.4
• /
• pp.10-24
• /
• 1991

본 연구에서는 기상 성장법 (VPE : vapor phase epitaxy) 으로 성장된 $n^+(Si:2X10^18cm^-3)$/$n(Si:1x10^17cm^-3)$구조의 시편 위에 SiN 과 감광막 등 식각 선택비가 서로 다른 두 물질로 보호된 소스와 드레인 사이의 게이트 형성 영역을 건식식각과 습식식각방법으로 리세스 에칭을 하여 형성한 후, 게이트를 자기정렬하여 형성시킬 수 있는 이중 리세스공정 기술을 개발하였고, 이를 통하여 전력용 MESFET 소자를 제작하였다.게이트 형성부분의 wide recess 폭은 건식식각으로 SiN을 측면식각(lateral etch) 함으로써 조절하였는데, 이 방법을 사용하여 MESFET 소자의 임계전압을 조절할 수 있고, 동시에 소스-드레인 항복전압을 30V 까지 향상시킬 수 있었다. 소스-드레인 항복전압은 wide recess 폭이 증가함에 따라, 그리고 게이트 길이가 길어짐에 따라 증가하는 경향을 보여주었다. 이 방법으로 제작한 여러종류의 MESFET 중에서 게이트 길이가 $2\mum$이고 소스-게이트 간격이 $3 \mum$인 MESFET의 전기적 특성은 최대 트랜스컨덕턴스가 120 mS/mm, 게이트 전압이 0.8V 일 때 포화드레인전류가 170~190mA/mm로 나타났다. 제작된 MESFET이 ($NH_4$)$_2$$S_x$ 용액에 담금처리될때 , 공기중에 노출된 게이트-드레인 사이의 n-GaAs층의 표면이 유황으로 보호되어 공기노출에 의한 표면 재산화막의 형성이 억제되었기 때문으로 사료된다.

• Tribology and Lubricants
• /
• v.11 no.2
• /
• pp.15-23
• /
• 1995

A zero-load slider is composed of two outside rails which produce a lift force pushing up the slider from the disk surface and a wide reverse step region which produces a suction force attracting the slider to the disk surface. In this paper, the flying characteristics of zero-load sliders are obtained by using an optimization technique. In the pressure calculation module, the FIFD scheme is used to solve the modified Reynolds equation. The BFGS method and a line search algorithm is employed to predict the static flying attitude. To investigate the effect of the geometric- parameters of zero-load sliders on the flying characteristics, recess depth, front step width, rail width, and taper height are varied and the corresponding flying attitudes are obtained. Simulation results demonstrate that recess depth and rail width have significant influences on the flying characteristics.

• ETRI Journal
• /
• v.27 no.3
• /
• pp.304-311
• /
• 2005

We report on the fabrication of an AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor (PHEMT) using a dielectric-defined process. This process was utilized to fabricate $0.12\;{\mu}m\;{\times}\;100 {\mu}m$ T-gate PHEMTs. A two-step etch process was performed to define the gate footprint in the $SiN_x$. The $SiN_x$ was etched either by dry etching alone or using a combination of wet and dry etching. The gate recessing was done in three steps: a wet etching for removal of the damaged surface layer, a dry etching for the narrow recess, and wet etching. A structure for the top of the T-gate consisting of a wide head part and a narrow lower layer part has been employed, taking advantage of the large cross-sectional area of the gate and its mechanically stable structure. From s-parameter data of up to 50 GHz, an extrapolated cut-off frequency of as high as 104 GHz was obtained. When comparing sample C (combination of wet and dry etching for the $SiN_x$) with sample A (dry etching for the $SiN_x$), we observed an 62.5% increase of the cut-off frequency. This is believed to be due to considerable decreases of the gate-source and gate-drain capacitances. This improvement in RF performance can be understood in terms of the decrease in parasitic capacitances, which is due to the use of the dielectric and the gate recess etching method.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.17-20
• /
• 2000

We have enhanced the yield of 0.25 ${\mu}{\textrm}{m}$ T-gate $Al_{0.25}$G $a_{0.75}$As/I $n_{0.2}$G $a_{0.8}$As P-HEMT using three-layer E-beam lithography process and selective etching process. The three-layer resist structure (PMMA/copolymer/ PMMA=2000 $\AA$/3000 $\AA$/2000 $\AA$) and three developers (Benzene：IPA=1：1,Methanol：IPA =1：1,MIBK：IPA=1：3) were used for fabrication of a wide-head T-gate by the conventional double E-beam exposure technology. Also 1 wt% citric acid： $H_2O$$_2$：N $H_{4}$OH(200m1：4ml：2.2ml) solution were used for uniform gate recess. The etching selectivity of GaAs over $Al_{0.25}$G $a_{0.75}$As is measured to be 80. So these P-HEMT processes can be used in X-band MMIC LNA fabrication.ion.ion.ion.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.77-79
• /
• 1992

We propose a self-aligned and double recessed technique for GaAs power MESFETs application. The gate length and the wide recess width are defined by a selective removal of the SiN layer using reactive ion etching(RIE) while the depth of the channel is defined by chemical etching of GaAs layers. The threshold voltages and the saturation drain voltage could be sucessfully controlled using this technique. The lateral-etched distance increases with the dry etching time and the source-drain breakdown voltage of MESFET increases up to about 30V at a pinch-off condition. The electrical characteristics of a MESFET with a gate length of 2 x10S0-6Tm and a source-gate spacing of 33 x10S0-6Tm show maximum transconductance of 120 mS/mm and saturation drain current density of 170-190mA/mm at a gate voltage of 0.8V.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.1
• /
• pp.31-38
• /
• 2002

In order to improve the 0.35 $mutextrm{m}$-via hole etching process the etching characteristic of the gas $C_2F_{6}$ has been analyzed. The samples were triple-layer films(TEOS/SOG/TEOS) on 8-inch wafers and the orthogonal array matrix technique was used for the process. The equipment for etching was the transformer coupled plasma (TCP) source which is a type of high density plasma(HDP). This experiment showed the etching rate for $C_2F_{6}$ was 0.8 $mutextrm{m}$/min-1.1 $mutextrm{m}$/min and the measured uniformity was under $pm$6.9% in the matrix window. The CD skew comparison between pre and post-etching was under 10% which is an outstanding results in the window of profile in anisotropic etching. There was no problem in C2F6 with the flow rate of 20sccm, but when 14sccm of $C_2F_{6}$ was supplied there was a recess problem on the inner wall of SOG film. Consequently the etching characteristic of $C_2F_{6}$ shows a fast etching rate and a very wide process window in HDP TCP.

• Journal of Korea Water Resources Association
• /
• v.30 no.6
• /
• pp.777-785
• /
• 1997

This study was conducted to clarify the hydrological characteristics of subsurface flow through a soil matrix and macropores. The research facility was set up in a 20m-1ong trench excavated down to bedrock at the base of a hillslope in the Panola catchment under USGS Georgia district. 13 macropores were found on the trench face and 6 major macropores were monitored. Matrix and macropore flow were measured during 95.5mm rainfall on March, 6 to 7. 1996. Macropore flow had great influence on formation of peak flow because the delivery time to Peak flow of macropore flow were faster about 10hrs than those of matrix flow. Matrix flow continued to recess for 3 days. On the other hand, macropore flow stopped within 12hrs after the event ceased. This means that matrix flow controls the recession part. The spatial variations of matrix and macropore flow between each trough and collector were very large by a wide range of 8,655.3 $\ell$ to 17.8 $\ell$ . The bed rock surface topography relates closer with the spatial variations of the flow than the surface one.