• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.343-344
• /
• 2012

In high power PV generation system, the solar cell normally generates wide output voltage depending on the insolation, cell's temperature and shade effect. This paper will propose a high efficiency converter allowing the wide input voltage to supply stable voltage with the controller and operation for the PV generation system. The proposed converter consists of two stages comprising SEPIC with a coupled inductor and LLC, which generates 24 V of output at the final output terminal. In this paper, a design method and experimental results with a test-bed of 50 W will be presented to validate the proposed converter.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.395-398
• /
• 2004

High-linearity voltage-controlled current sources (VCCSs) circuits for wide voltage-controlled oscillator and automatic gun control were proposed. The VCCS consists of emitter follower for voltage input, two common-base amplifier which their emitter connected for current output, and current mirror which connected the two amplifier for large output current. The VCCS used only five transistors and a resistor without an extra bias circuit. Simulation results show that the VCCS has current output range from 0mA to 300mA over the control voltage range from 1V to 4.8V at supply voltage 5V. The linearity error of output current has less than $1.4\%$ over the current range from 0A to 300mA.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.7
• /
• pp.97-103
• /
• 2002

In this paper, a Logarithmic Video Amplifier(LVA) for radar system or satellite communications is described. The proposed LVA is composed of a input stage, amplification stage, and output stage. As well as a novel series-parallel architecture is proposed for the purpose of wide dynamic range and high speed operation, a newly developed input stage is designed in order to control the voltage level between LVA and detector diode. The LVA is fabricated with a 1.5um 2-poly 2-metal n-well Bi-CMOS technology, and the chip area is 1310 um x 1540 um. From the experimental results, it consumes 190 mW at 10V power supply, the chip has 60 dB dynamic range and 100ns falling time.

• Journal of the Optical Society of Korea
• /
• v.8 no.3
• /
• pp.104-107
• /
• 2004

The periodic transmission spectrum of a solid etalon for wide-band capability is analyzed both theoretically and experimentally. In the transmission spectrum with an incident area of a photodetector, the peak wavelength and transmittance are deeply dependent on the incident angle and the divergence angle of the input laser beam. A thermal adjustment for a solid etalon is an optional way to control the transmission spectrum instead of the inefficient fine-angle alignment. In the result, we present the deviations of free spectral range (FSR) by the change in angle and temperature over wide wavelength range.

• Journal of Sensor Science and Technology
• /
• v.26 no.4
• /
• pp.223-227
• /
• 2017

Conventional CMOS image sensors (CISs) have a trade-off relationship between dynamic range and sensitivity. In addition, their sensitivity is determined by the photodiode capacitance. In this paper, CISs that consist of dual-sensitivity photodiodes in a unit pixel are proposed for achieving wide dynamic ranges. In the proposed CIS, signal charges are generated in the dual photodiodes during integration, and these generated signal charges are accumulated in the floating-diffusion node. The signal charges generated in the high-sensitivity photodiodes are transferred to the input of the comparator through an additional source follower, and the signal voltages converted by the source follower are compared with a reference voltage in the comparator. The output voltage of the comparator determines which photodiode is selected. Therefore, the proposed CIS composed of dual-sensitivity photodiodes extends the dynamic range according to the intensity of light. A $94{\times}150$ pixel array image sensor was designed using a conventional $0.18{\mu}m$ CMOS process and its performance was simulated.

• ETRI Journal
• /
• v.33 no.3
• /
• pp.366-373
• /
• 2011

In this paper, we propose a low-power all-digital phase-locked loop (ADPLL) with a wide input range and a high resolution time-to-digital converter (TDC). The resolution of the proposed TDC is improved by using a phase-interpolator and the time amplifier. The phase noise of the proposed ADPLL is improved by using a fine resolution digitally controlled oscillator (DCO) with an active inductor. In order to control the frequency of the DCO, the transconductance of the active inductor is tuned digitally. The die area of the ADPLL is 0.8 $mm^2$ using 0.13 ${\mu}m$ CMOS technology. The frequency resolution of the TDC is 1 ps. The DCO tuning range is 58% at 2.4 GHz and the effective DCO frequency resolution is 0.14 kHz. The phase noise of the ADPLL output at 2.4 GHz is -120.5 dBc/Hz with a 1 MHz offset. The total power consumption of the ADPLL is 12 mW from a 1.2 V supply voltage.

• Journal of Sensor Science and Technology
• /
• v.21 no.1
• /
• pp.1-6
• /
• 2012

Using a current-mode multiple reset, a current-to-voltage(I-V) converter with a wide dynamic range was produced. The converter consists of a trans-impedance amplifier(TIA), an analog-to-digital converter(ADC), and an N-bit counter. The digital output of the I-V converter is composed of higher N bits and lower bits, obtained from the N-bit counter and the ADC, respectively. For an input current that has departed from the linear region of the TIA, the counter increases its digital output, this determines a reset current which is subtracted from the input current of the I-V converter. This current-mode reset is repeated until the input current of the TIA lies in the linear region. This I-V converter is realized using 0.35 ${\mu}m$ LSI technology. It is shown that the proposed I-V converter can increase the maximum input current by a factor of $2^N$ and widen the dynamic range by $6^N$. Additionally, the I-V converter is successfully applied to a photometric sensor.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.976-979
• /
• 2002

A new controller for switching audio power amplifier with digital PWM input is proposed- Bi-directional Saw-tooth Error Correction (BSEC). This control method for high quality switching amplifier is based on a pulsed edge correction approach using PWM audio signal input as a reference of power switching digital to analog converter. The proposed controller has excellent features such as wide error correction range and no limitation on the modulation index. The controller is implemented in the half-bridge class D amplifier and the performance is verified through hardware experiments. It delivers 100W into 4${\Omega}$ load with less than 0.2% of total harmonic distortion (THD) all over operating range and an maximum efficiency of 82%.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.363-364
• /
• 2010

Most LED drivers uses current control method to adjust LED current. Using AC power grid such as off-line converter, Buck topology is popular because input voltage of LED driver is much higher than LED output voltage. Normally DCM current control is more popular than CCM current mode control in the range of below 50W, But DCM characteristics are dependent on the input voltage variation. This paper deals with what should be considered in DCM for LED driver with valley fill circuit.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.520-527
• /
• 2016

A new dual-loop digital delay-locked loop (DLL) using a hybrid (binary + sequential) search algorithm is presented to achieve both wide-range operation and high delay resolution. A new phase-interpolation range selector (PIRS) and a variable successive approximation register (VSAR) algorithm are adopted to resolve the boundary switching and harmonic locking problems of conventional digital DLLs. The proposed digital DLL, implemented in a $0.18-{\mu}m$ CMOS process, occupies an active area of $0.19mm^2$ and operates over a wide frequency range of 0.15-1.5 GHz. The DLL dissipates a power of 11.3 mW from a 1.8 V supply at 1 GHz. The measured peak-to-peak output clock jitter is 24 ps (effective pk-pk jitter = 16.5 ps) with an input clock jitter of 7.5 ps at 1.5 GHz. The delay resolution is only 2.2 ps.