• Journal of the Korean Institute of Intelligent Systems
• /
• v.23 no.4
• /
• pp.286-291
• /
• 2013

In this paper, in-line type flip chip bump 3D inspection equipment, using white light interferometer with large F.O.V., which is aimed to be used in flip chip bump test process is developed. Results of flip chip bump height measurement in many substrates and repeatability test results for the bumps in fixed location of each substrate are shown. Test results from test bench and those from developed flip chip bump 3D inspection equipment are compared and as a result repeatability is improved by reducing the impact of system vibration. A valuation basis for the testing quality of flip chip bump 3D inspection equipment is proposed.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.1
• /
• pp.189-196
• /
• 2014

Water dispersible ZnS based nanocrystals: ZnS (blue), ZnS:Cu (green) and ZnS:Mn (yellow-orange) were synthesized by capping the surface of the nanocrystals with a mercaptopropionic acid (MPA) molecule. The MPA capped ZnS based nanocrystal powders were characterized by using XRD, HR-TEM, EDXS, FT-IR, and FT-Raman spectroscopy. The optical properties of the colloidal nanocrystals were also measured by UV/Vis and photoluminescence (PL) spectroscopies in aqueous solvents. The PL spectra showed broad emission peaks at 440 nm (ZnS), 510 nm (ZnS:Cu) and 600 nm (ZnS:Mn), with relative PL efficiencies in the range of 4.38% to 7.20% compared to a reference organic dye. The measured average particle sizes from the HR-TEM images were in the range of 4.5 to 5.0 nm. White light emission was obtained by mixing these three nanocrystals at a molar ratio of 20 (ZnS):1 (ZnS:Cu):2 (ZnS:Mn) in water. The measured color coordinate of the white light was (0.31, 0.34) in the CIE chromaticity diagram, and the color temperature was 5527 K.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.1
• /
• pp.24-27
• /
• 2013

In this paper, we investigated the effect of luminescence properties of various concentrations of magnesium-doped ZnS:Mn phosphor excited by plasma luminescence device. The PL intensity was evaluated in the range of 300~500 nm excitation wavelengths. We found the highest PL intensity of the phosphors excited by 365 nm and 450 nm was observed at Mg concentrations of 1.4 wt% and 0.8 wt%, respectively. In addition, an emission peak was distinguished at 580 nm wavelength. With increasing Mg dopant level, enhanced PL intensity was observed, which is possibly applicable to color converting materials by blue emission for white light sources. Finally, we evaluated the luminance properties of color converting ZnS:Mn,Mg phosphors with plasma blue light source. the white luminance of plasma light source with CIE(0.36,0.26) was established by color converting phosphors of ZnS:Mn with 0.8 wt% Mg.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.6
• /
• pp.476-481
• /
• 2014

In this paper, we design the pre-equalizer of transmitter circuit in order to enhancement modulation bandwidth of white LED which is light source of VLC (Visible Light Communication). Also, we eliminate yellow light component by optical filtering which mitigate frequency response of white LED. Power loss by optical filtering is overcome by using convex lens. By applying proposed system, 3 dB bandwidth deciding modulation bandwidth of white LED increases from 3 MHz to more than 25 MHz and the transmission distance increases by optical design which secure additional signal power. We optically modulate NRZ-OOK signal to LED and receive light signal using APD. We analyze received data using CSA and RFSA. As a result, we experimently demonstrate the possibility that transmits NRZ-OOK signal up to 30 Mbps in 4.5 m, 50 Mbps in 1.5 m through the pre-equalizer and optical design.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.46 no.3
• /
• pp.59-68
• /
• 2023

Currently, yellow phosphor of Y3Al5O12:Ce3+ (YAG:Ce) fluorescent material is applied to a 450~480nm blue LED light source to implement a white LED device and it has a simple structure, can obtain sufficient luminance, and is economical. However, in this method, in terms of spectrum analysis, it is difficult to mass-produce white LEDs having the same color coordinates due to color separation cause by the wide wavelength gap between blue and yellow band. There is a disadvantage that it is difficult to control optical properties such as color stability and color rendering. In addition, this method does not emit purple light in the range of 380 to 420nm, so it is white without purple color that can not implement the spectrum of the entire visible light spectrum as like sunlight. Because of this, it is difficult to implement a color rendering index(CRI) of 90 or higher, and natural light characteristics such as sunlight can not be expected. For this, need for a method of implementing sunlight with one LED by using a method of combining phosphors with one light source, rather than a method of combining red, blue, and yellow LEDs. Using this method, the characteristics of an artificial sunlight LED device with a spectrum similar to that of sunlight were demonstrated by implementing LED devices of various color temperatures with high color rendering by injecting phosphors into a 405nm deep blue LED light source. In order to find the spectrum closest to sunlight, different combinations of phosphors were repeatedly fabricated and tested. In addition, reliability and mass productivity were verified through temperature and humidity tests and ink penetration tests.

• Korean Journal of Environment and Ecology
• /
• v.30 no.5
• /
• pp.821-828
• /
• 2016

We examed physiological and flowering response of S. capitata, the endangered plant in Korea, under LED light conditions in plant factory to cultivate artificially for conservation. We cultivated S. capitata and measured its physiological responses and the number of flowers under red, blue, white, red+far-red mixed, red+blue mixed, and red+blue+white mixed light. The results showed that its photosynthetic rate and chlorophyll content were recorded relatively high in red+blue+white and red+blue mixed light respectively. Transpiration rate and stomatal conductance appeared relatively high in the white single light while water use efficiency was no difference. Photochemical efficiency of photochemical photosystem II by minimum and maximum chlorophyll fluorescence was the highest in the red+blue+white mixed light condition than other ones. The number of flowers of S. capitata was at its peak under the red light or red+far-red mixed light. Therefore, we conclude that the most efficient way to grow for flowering of S. capitata is to provide red light or red+far-red mixed light in the plant factory.

• Journal of Convergence Society for SMB
• /
• v.6 no.4
• /
• pp.99-106
• /
• 2016

In this paper, we propose an adaptive FEC scheme in visible light communication using white LED. To this end, we investigate the red, green and blue mixing ratio of white LED in order to achieve the white color, and the mixing ratio of those wavelength can be defined as 4 types. Based on those properties, the FEC technique is applied to the wavelength band with the lowest mixing ratio according to mixing ratio types. At that point, we use a LDPC channel coding scheme as the FEC technique. Therefore, the proposed system can mitigate the reduction of data rate and improve total BER performance.

• Korean Journal of Materials Research
• /
• v.16 no.4
• /
• pp.231-234
• /
• 2006

To obtain balanced white-emission and high efficiency of the organic light-emitting diodes (OLEDs), a deep blue emitter made of N,N'-diphenyl-N,N'-bis(1-naphthyl)- (1,1'-biphenyl)-4,4'-diamine (NPB) emitter and a new red emitter made of the Bis(2,4 -dimethyl-8-quinolinolato)(triphenylsilanolato)aluminum(III) (24MeSAlq) doped with red fluorescent 4-(dicyanomethylene)-2-tert-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H -pyran (DCJTB) were used and the device was tuned by varying the thickness of the DCJTB-doped 24MeSAlq and $Alq_3$. For the white OLED with 10 nm thickness DCJTB (0.5%) doped 24MeSAlq and 45 nm thick $Alq_3$, the maximum luminance of about 29,700 $Cd/m^2$ could be obtained at 14.8 V. Also, Commission Internationale d'Eclairage (CIE) chromaticity coordinates of (0.32, 0.28) at about 100 $Cd/m^2$, which is very close to white light equi-energy point (0.33, 0.33), could be obtained.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.2
• /
• pp.93-97
• /
• 2013

We studied the emission characteristics of white phosphorescent organic light-emitting diodes (PHOLEDs), which were fabricated using a two-wavelength method. To optimize emission characteristics of white PHOLEDs, white PHOLEDs with co-doping and blue/co-doping emitting layer (EML) structures were fabricated using a host-dopant system. The total thickness of light-emitting layer was 25 nm and the dopant of blue and red was FIrpic and $Bt_2Ir(acac)$ in UGH3, respectively. In case of co-doping structure, applying micro lens array film showed efficiency improvement from the current efficiency 78.5 cd/A and power efficiency 40.4 lm/W to the current efficiency 131.1 cd/A and power efficiency 65 lm/W and blue / co-doping structure showed efficiency improvement from the current efficiency 43.8 cd/A and power efficiency 22 lm/W to the current efficiency 69 cd/A and power efficiency 32 lm/W.

• Journal of Information Display
• /
• v.3 no.2
• /
• pp.6-12
• /
• 2002

In order to achieve white emission from organic light emitting devices (OLEDs), five distinct structures were fabricated and tested. The white emission was obtained using two different color-emitting materials (yellow from rubrene-doped $Alq_3$ and blue from DPVBi) with or without a carrier-blocking layer. For enhancing the red emission, two types of devices with three-color emitting materials were fabricated. The white emission, close to the CIE coordinate of (0.3,0.3), was achieved by using two blocking layers as well that as without a blocking layer. This paper covers the subject of controlling the location of exciton recombination zone. It has been found that there is a trade-off in that the devices with three color emitting layers do not show as much luminescence efficiency compared to those with two color emitting layers, but rather, show distinct red emission in the resultant emission spectra. The highest power efficiency was measured to be 1.15lm/W at 2,000 $cd/m^2$ for a structure with two color-emitting layers.