• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.1
• /
• pp.18-23
• /
• 2013

Omni-directional robot is a typical holonomic constraint robot that has three degrees of freedom movement in 2D plane. In this study, a new omni-directional robot whose wheels are arranged in radial directions was proposed to improve driving performance of the robot. Unlike a general omni-directional robot whose wheels were arranged in a circumferential direction, moments do not arises in the proposed robot when the robot travels in a straight line. To analyze driving performance, dynamic modeling of the omni-directional robot, which considers friction and slip, was carried out. By friction measurement experiments, the relationship between dynamic friction coefficient and relative velocity was derived. Dynamic friction coefficient according to the angle difference between robot travel direction and wheel rotation direction was also obtained. By applying these results to the dynamic model, driving performance of the robot was calculated. As a result, the proposed robot was 1.5 times faster than the general robot.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.442-445
• /
• 2011

Concrete track on the new railway lines of the existing roads are built on high ground, or less than 400m radius of the sharp curve sectors will occur. sharp curve sectors the rail and wheel friction, stick-slip due to the band of 1,000Hz or squeal noise occurs from the increase in civil complaints about noise is a real situation. In this study, discussed in previous studies, noise measurements for each radius of concrete track and frequency analysis, followed by the radius of the curve in order to investigate vibration characteristics of urban railway sector sharp curve radius less than 400m and 400m ~ 1,000 m further to the point selected track components(rails, sleepers, ballast) according to the vibration measurements and analysis of the frequency characteristics and the results were derived.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.1
• /
• pp.40-47
• /
• 2002

This paper describes a re-adhesion control method for the Korean High-Speed Train (KHST) with parallel induction motor drive. To keep a traction efficiency and to improve vehicle maintenance, the adhesion characteristics between wheel and rail are analyzed. Also the re-adhesion controller is designed as the subsystem of induction motor vector control. In order to verify performance of the proposed control techniques, the simulation is executed by train model and a downscaled re-adhesion control simulator is utilized. Both simulation and running test results show that good re-adhesion characteristics are obtained.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.2
• /
• pp.1-11
• /
• 1998

The 4WS system is usually developed to improve the maneuverability at low speed and the straight line stability at high speed, but it is found to have the severe understeer characteristics at high speed. Therefore a 4WS vehicle requires to turn the steering wheel much more than a 2WS vehicle at high speeds even a driver goes through the same curved road. In this study, to enhance the cornering performance of the 4WS vehicle at high speed, a DYC 4WS system is proposed based on the nonlinear 4WS system and direct yaw moment control system. Especially the proposed DYC 4WS system is able to realize a zero side slip angle for vehicles and a cornering performance similar to the 2WS vehicle at high speed.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.203-211
• /
• 2002

ABS (Anti-lock Braking System) is a safety device for preventing wheel locking in a sudden braking. It consists of hydraulic modulator, ECU(Electronic Control Unit) and angular velocity sensors. Its control methods are classified into three types; deceleration control, slip ratio control and deceleration/acceleration control. In this paper, ABS mounted vehicle is mathematically modeled and the proposed model is verified by actual cars experiments, and the braking characteristics of the control methods with pulse width modulation are compared and analyzed through computer simulations.

• Journal of Biosystems Engineering
• /
• v.18 no.3
• /
• pp.220-229
• /
• 1993

A dimensional analysis was carried out to investigate if model agricultural radial tire can predict the tractive performance of prototype tires. Experimental data was analyzed to prove the results of dimensional analysis. The results was summerized as follows ; 1. When the model and prototype tires are tested under the same soil conditions, inflation pressure, slip and dynamic load, traction coefficient ratio between two tires depend on the geometry of two tires. 2. According to the regression analysis of the experimental data, traction equation parameters of the prototype tires can be predicted from the that of model tire 3. Predicted traction coefficient of prototype tire, calculated from the traction equation paramters, showed good correlation with that of experimental results. Thus it was possible to predict net and gross traction of prototype tire from the model traction equation parameters.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.2649-2651
• /
• 2005

In trains driven by electric motor, when the adhesion force between rail and driving wheel decreases suddenly, the electric motor coach has slip phenomena. The characteristics of adhesion force coefficient are strongly affected by the conditions between rails and driving wheels, such as moisture, dust, and oil on the rails and so on. This paper proposes the vector control structure for the improved re-adhesion control with paralleled control of induction motors under the sudden variation of the adhesion force.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.2
• /
• pp.79-85
• /
• 2007

The skid-steering method that applied a number of mobile robot currently is very effective in narrow area. But it contains several problems of its natural properties, slip, occurred by different direction between vehicle's driving and wheel's rotary. From this thesis we want to suggest suitable structure of $6{\times}6$ skid steering wheeled vehicle and method of driving by analyzing the behavior of $6{\times}6$ skid-steered wheeled vehicle by engineering analytical method

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1729-1734
• /
• 2007

Recently, as the feasibility study shows that trans-Korea railway and trans-continental railway are advantageous, interest in high-speed railway system is increasing. Because railway vehicle is environment-friendly and safe compared with airplane and ship, its market-sharing increases gradually. We developed a measurement system for on-line test and evaluation of performances of KHST. The measurement system is composed of software part and hardware part. Perfect interface between multi-users is possible. Nowadays, position data inputs to pulse signal from wheel. Perfect position measurement was limited to slip and slide of vehicle. This measurement makes up for the weak points, Position Detection System using GPS develops. By using the system, Korean High Speed Train is capable of accurate fault position detection.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1005-1011
• /
• 2007

The brake system of train must posses the large braking effort in order to stop the train safely within the limited traveling distance. But, the excessive braking effort has been deteriorated the ride comfort due to high level of deceleration and jerk, and sometimes occurred the skid, because the applied braking force exceeds the allowable adhesive force. This skid causes not only to increase the stopping distance but also to deteriorate the safety of train and damage the rail surface by wheel flat. In the present paper, the braking force for disc brake of Korea High Speed Train (HSR350x) was measured through on-line test and the adhesion force was estimated by using the analytic model in the skid condition. Also, we have discussed the relationship between the actual disc brake force and the adhesion force in real skid condition.