• Journal of Hydrogen and New Energy
• /
• v.31 no.2
• /
• pp.194-201
• /
• 2020

Recently, Type 2 high-pressure hydrogen storage tank is studied due to fast defect detection, easy manufacturing, and cost efficiency. Moreover, the dry winding a high-strength metal wire will make increased economic efficiency compare with the wet winding method and the carbon/glass fiber winding method. In this study, a theoretical study on the dry winding of a Type 2 high pressure hydrogen tank using a metal wire was done, and the equations of the total stress on the aligned and the staggered winding for the hoop winding were derived, and the following results were obtained by using these equations. As the diameter of the metal wire, the number of winding layers, and the outer diameter of the liner increase, the maximum stress decreases, but the difference between the maximum stress occurring in the aligned winding and the staggered winding increases. As the pressure increases, the thickness of the winding layer increases, but as the strength of the metal wire increases, the thickness of the winding layer decreases. In addition, regardless of the strength of the metal wire, the thickness of the winding layer of the staggered winding was about 13.4% thinner than that of the aligned winding.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.3
• /
• pp.237-246
• /
• 2021

With climate change, debris flow has been increasing due to the collapse and erosion of shallow slopes caused by extreme rainfall. It is preferred to an economical and eco-friendly method rather than reinforcement of soil slopes with the earth anchor or nailing method. In this study, a soil improvement agent was developed by utilizing insitu soil, leaf mold, and used harbal medicine to help sufficient vegetation. In addition, to prevent surface erosion, shear strength of the soil was increased by using micro cement and hemihydrate gypsum as additives. The optimum mix ratio of the mixture is determined by increasing the shear strength by checking the erosion progress of the ground surface layer due to rainfall through an laboratory test. The safety factor of soil slope has been improved on the slope surface reinforced by the improvement agent, and the strength of erosion has been increased, making it efficient to cope with heavy rain during wet season.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.2
• /
• pp.155-162
• /
• 2005

This paper presents an invetigation into the cause of deterioration of wet surrounding RC structures subjected to checmical attacks such as sewage. The antibacterial-reforming agent is developed after determining the permeability of the RC structure. After application of the anitbacterial-reforming agent through SEM, the permeability, compressive strength properties and the micro-structure of the concrete were evaluated for durability. In addition, the antibacterial-reforming agent was combined with a protective coating for the wet surrounding RC structure and evaluated for durability. The combined effect of the antibacterial-reforming agent and the protective coating were evaluated in field tests in both sewer system and tunnel sites.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.4
• /
• pp.49-56
• /
• 2007

Effects of post-baking treatment conditions on the interfacial adhesion between electroless plated Ni and polyimide film were evaluated using $180^{\circ}C$ peel test. Measured peel strength values monotonically decrease from $38.6{\pm}1.1g/mm\;to\;26.8{\pm}2.2g/mm$ for the variations of post-baking treatment temperatures from $80^{\circ}C\;to\;180^{\circ}C$, respectively. Wet chemical treatment on the polyimide surface produces carboxyl and amide functional groups on the surface which is closely related to the change in interfacial adhesion between electroless Ni and polyimide films. It is speculated that interfacial adhesion seems to be controlled by carbonyl oxygen bonding near cohesive failure region during post-baking treatment.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.953-956
• /
• 2008

The present study was to develop a dry PFB method similar to the existing gypsum board construction method in order to apply the existing wet PFB method that uses fire.resistant adhesive. It was found that the existing wet method can produce concrete compressive strength of 80MPa and fire resistance of 3 hours with 30mm PF boards. The goal of development in this study was fire resistance of 3 hours through dry construction of 15mm fire.resistant boards.According to the results of fire resistance test, when the dry PF method was applied, the temperature of the main reinforcing bar was 116$^{\circ}$C in 15mm, 103.8$^{\circ}$C in 20mm, and 94$^{\circ}$C in 25mm, and these results satisfied the current standards for fire resistance control presented by the Ministry of Land, Transport and Maritime Affairs. When a 3.hour fire resistance test was performed and the external properties of the specimen were examined, the outermost gypsum board hardly remained and internal PF board maintained its form without thermal strain.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.153-158
• /
• 2002

$Al_2O_3$ composites powders with 1∼11 wt% $TiO_2$ were prepared by wet method and sintered at 1350$^{\circ}C$, 1450$^{\circ}C$ for 2h. Mechanical properties and microstructural evolution were investigated in this study. $Al_2O_3$-3 wt% $TiO_2$ composite were high bulk density of 2.37 g/$cm^3$ and low apparent porosity of 6.3%. The composites containing of 3 wt% $TiO_2$ showed moderately high bending strength of 68.9 MPa and the young's modulus of 35.5 MPa. The composites with increasing $TiO_2$ contents exhibit reduced thermal expansion coefficient due to the formation of $Al_2TiO_5$ phase.

• Journal of the Korea Concrete Institute
• /
• v.26 no.5
• /
• pp.607-614
• /
• 2014

The purpose of this dissertation was to investigate the effect of mineral admixtures, such as fly ash, blast furnace slag powder, meta kaolin and silica fume, on the basic properties and durability of crushed sand shotcrete, selecting a series of shotcrete mixtures with a variable admixture. Compressive strength increased as the content of mineral admixtures increased, specially it was the most effective when using meta kaolin both at sample specimen and core after shotcreting. Rapid chloride ion permeability test and sulfuric acid resistance test showed that both durability increased as the substitute rate of mineral admixture increased. In air void analysis with image analysis, the targeted the spacing factor and specific surface were not satisfied because air-entrained agent was not used.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.1
• /
• pp.1-9
• /
• 2016

While the amount of construction waste has not been changed much in discharge for last 10 years, the recycled resources refined from construction waste have been mainly applied to low-leveled one such as reclamation, back-fill, road base or subbase and so on. Thus this study addresses the applicability of recycled fine aggregate as a replaceable material in precast concrete. To evaluate the possibility, both of dry and wet processes were adopted as well as steam curing, widely used in the field for rapid producing. Most important experimental parameters were driven through preliminary experiments and were evaluated in terms of concrete properties. It is found from aggregate-replacement tests that all of consistency and strengths of concrete were decreased as the ratio of recycled fine aggregate increased, and the amount of decrease can be estimated using proposed equations. Though the recycled fine aggregate showed a decrease of concrete properties more or less, the applicability in large volume as a constituent of precast product was well noted from experimental results.

• Composites Research
• /
• v.29 no.5
• /
• pp.256-261
• /
• 2016

In this work, we have prepared the filter papers with the pitch-based activated carbon fibers and the binder fibers using wet-laid process. The influence of the binder fiber on the porosity of the filter papers has been investigated by using nitrogen adsorption isotherms at 77 K and a scanning electron microscope (SEM). As a result, the specific surface area has increased with an decrease in the content of binder fiber. It has been shown that the optimum ratio of pitch-based activated carbon fibers and the binder fibers is 70:30, resulting in high porosity, excellent bonding strength, large specific surface area ($650.4m^2/g$) and high noxious gas removal efficiency (86.9%). In addition, it has been observed that the mean pore size distribution of the fiber papers has not been affected by the binder fiber.

• Journal of Fashion Business
• /
• v.21 no.2
• /
• pp.105-112
• /
• 2017

A string wallcovering is a kind of textile wallcovering which is made of cellulose fiber yarn laminated on base paper. Compared with normal paper or PVC wallpaper, a string wallcovering is preferred continually in the interior design market, as it is not only environmentally friendly but it also has less cost on mass production without the weaving process and has a natural visual effect, excellent functionality such as thermo keeping, permeability, sound absorption. However, in the dyeing process, it is not appropriate to use plenty of energy such as water, electricity, steam or chemicals considering the environmental trend and the government policy plenty of energy such as water, electricity, steam or chemicals. Currently, a string wallcovering is made of raw white yarn and padding with direct dye or pigment which includes toxic elements, especially the use of direct dye is restricted in a part of the developed country due to inclusion of azo. In this study, we researched dyeing based on cold pad batch dyeing of a string wallcovering with reactive dyestuff. The peel strength and bending depth test confirmed that the optimum adhesive type and spread amount improved the water resistance of the string wallcovering. Also, pad batch dyeing with optimum reactive dyestuff enhanced the color fastness to light and rubbing in dry and wet conditions. Additionally, for improvement of color fastness to rubbing in a wet condition, the additional treatment finishing without soaping process which is used water. The results of this study can be used as basic data for environmentally friendly and energy saving of the textile wallcovering.