• 한국항공우주학회지
• /
• 제38권11호
• /
• pp.1115-1122
• /
• 2010

본 논문에서는 샌드위치-적층판 단일겹침 접착 조인트의 정적강도를 시험을 통해 연구하였다. 접착제의 두께(3종류 : 0.2, 2, 4 mm)와 환경조건(2가지 : 상온, 고온흡습)을 변화시키면서 총 38개의 시편을 제작하여 시험을 수행하였다. 시험 결과, 접착제의 두께가 0.2mm에서 2 mm 와 4 mm로 증가함에 따라 체결부의 파손강도가 각각 16% 와 30% 정도 감소하는 것으로 나타났다. 반면 고온흡습 환경에서의 파손강도는, 접착제의 두께가 0.2mm인 경우를 제외하면, 접착제의 열화현상이 적층판과 샌드위치 면재의 층간분리 혹은 층내분리 파손을 지연시켜, 상온건조 환경에 비해 약 12% 가량 높게 나타났다. 접착제의 두께가 얇은 0.2 mm의 경우 시험환경의 효과는 나타나지 않았다.

• 접착 및 계면
• /
• 제17권3호
• /
• pp.104-109
• /
• 2016

AC 코로나와 DC 코로나 처리 효과들을 비교하기 위해 선행연구의 DC 코로나 처리 조건들과 같이 폴리에스테르 직물들을 전류세기 5, 10, 15 A로, 공급속도 5, 10, 15 m/min로 AC 코로나 처리하였다. 이들의 표면변화를 주사전자현미경(SEM)과 X-ray 광전자분석기(XPS)로 확인하였고, 또한 물리적 성질의 변화를 건조 시와 습윤 시의 접착강도를 통하여 측정하였다. 대기압에서 AC 코로나 방전처리에 의해 폴리에스테르 직물의 표면변화는 DC 코로나 방전과 유사한 경향을 보였다. 일반적으로 AC, DC 코로나 처리 양쪽에서 건조 시의 접착강도는 전류세기와 공급속도가 증가할수록 증가하였으나, 습윤 시의 접착강도는 전류세기가 증가할수록 공급속도가 감소할수록 증가하였다. 전류가 20 A일 때 DC 코로나 방전에서는 탄화가 발생하였으나 AC 코로나에서는 탄화가 발생하지 않았다.

• Advances in concrete construction
• /
• 제15권5호
• /
• pp.333-348
• /
• 2023

Fast infrastructure development boosts the demand for shotcrete. Despite sand and stone being the most common coarse and fine aggregates for shotcrete, excessive exploration of these materials challenges the ecological environment. This study utilized an industrial solid waste, high-titanium heavy slag, blended with steel fibers to form Wet Shotcrete of Steel Fiber-reinforced High-Titanium Heavy Slag (WSSFHTHS). It investigated its workability, shotcrete performance and mechanical properties under different water-to-cement ratios, fly ash content, superplasticizer dosage, and steel fiber content. The tunnel excavation and support were investigated by conducting finite element numerical simulation analysis and was used in 3 tunnel lining pipes in Zhonggouwan tailing pond. The major findings are as follows: (1) The water-to-cement ratio (w/c ratio) significantly impacted the compressive strength of WSSFHTHS. The highest 28-day compressive strength of 60 MPa was achieved when the w/c ratio was 0.38; (2) Adding fly ash improved the workability and shotcrete performance and strength development of WSSFHTHS. The best anti-permeability performance was achieved when the fly ash constituted 15%, with the lowest permeability coefficient of 4.596 × 10-11 cm/s; (3) The optimum superplasticizer dosage for WSSFHTHS is 0.8%. It provided the best workability and shotcrete performance. Excessive dosage resulted in water bleeding and poor aggregate encapsulation, while insufficient dosage decreased flowability and adversely affected shotcrete performance; (4) The dosage of steel fibers significantly impacted the flexural and tensile strength of WSSFHTHS. When the steel fiber dosage was 45 kg/m³, the 28-day flexural and tensile strengths were 8.95 MPa and 6.15 MPa, respectively; (5) By integrating existing shotcrete techniques, the optimal lining thickness was 80 mm for WSSFHTHS per simulation. The results revealed that after using WSSFHTHS, the displacement of the tunnel surrounding the rock significantly improved, with no cracks or hollows, similar to the simulation results.

• 마이크로전자및패키징학회지
• /
• 제6권1호
• /
• pp.59-64
• /
• 1999

본 연구에서는 솔더링(soldering)공정 전, 기판의 최적의 건조 시간과 PCB기판에 묻은 수분이 솔더링에 미치는 영향에 대하여 조사하고자 하였다. 실험결과, 솔더링 중 건조시간이 증가할수록 솔더링성(solderabillity)이 향상됨을 알 수 있었다. 즉, 건조된 시편이 함습한 시편에 비해 젖음 시간(wetting time)이 약 0.2초 짧고 젖음력(wetting force)이 2~4mN증가되었다. 338k에서 30분 이상 건조시켰을 때 최소 미납 결함과 리드와 기판의 최고 인장강도가 얻어 졌다. 또, 건조시간을 45분가지 증가시킬 때, 건조시간 증가에 따라 솔더볼 발생 양이 감소하였다.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.115-126
• /
• 2001

In this paper, through a series of comparative experiments, effects of two different cure processing methods, cocure and precure, on the mechanical properties of honeycomb core materials for aircraft applications are considered. Mass of moisture accumulated into the closed cells of the sandwich panel specimen from the measured mass of moisture diffused to the full saturation state into the elements(skin, adhesive layer, Nomex honeycomb), consisting the honeycomb sandwich specimen has been calculated. Water reservoir of 70$\^{C}$ was used to have specimens absorb moisture to see the influence of moisture absorbed into sandwich panel on its mechanical properties. For the repair condition holding for 2 hours at 177$\^{C}$(350℉) temperature, a pressure due to the vapor expansion in each cell of the sandwich panel, which may result in the local separation of the interface between laminated skin and the surface of the honeycomb, has been estimated by vapor pressure-temperature relation from the thermodynamic steam table and compared to the pressure from the ideal gas state equation. The bonding strengths of the laminated skins on the flat surface of the Nomex honeycomb have been compared by the flatwise tension test and climbing drum peel test performed at room temperature for dry, wet and wet-repair specimens, respectively.

• 펄프종이기술
• /
• 제42권1호
• /
• pp.26-34
• /
• 2010

Effects of drying condition (IR radiation) on the optical properties and the printability of coated paper were elucidated at various latex sizes and low and high coating color concentrations. It was found that the smaller latex provided better rheology and higher dry and wet pick strength than the larger one. The high solids coating resulted in higher paper gloss and smaller roughness than the low solids coating, even though the clay addition was reduced by 20 parts in the high solids coating. Increasing IR radiation prohibited binder migration into the base paper. Thus it improved binder distribution and decreased pores in the coated layer, resulting in the increased dry and wet pick strength and the improved printing gloss. On the other hand, the color trapping and ink set-off was impaired with increasing IR radiation. Print mottle index passed through a maximum with increasing IR radiation.

• 펄프종이기술
• /
• 제45권5호
• /
• pp.37-43
• /
• 2013

This study was focused on applying a new paper coating binder, vinyl acetate-ethylene(VAE) emulsion, with SB-latex and acrylic emulsion for paper coating application. VAE emulsion has a low monomer cost and is non-toxic chemical than conventional adhesive for paper coating such as styrene-butadiene latex( SB-latex) and acrylic emulsion. We conducted double coating in order to test VAE emulsion, which was applied on top surface only. The results showed that optical properties of the coated paper with VAE were similar with the SB-latex binders. In case of bonding strength, dry-pick of the coated paper with VAE showed almost same with other binders while wet-pick of the coated paper with VAE had a little bit lower strength than that with SB-latex.

• 한국염색가공학회지
• /
• 제19권1호
• /
• pp.24-30
• /
• 2007

Heat storage/release system in textile is a useful tool to increase energy efficiency and enhance comfortable microclimate of clothing. Phase change materials(PCM) are used in regulating storage and release properties of thermal energy. To investigate the temperature regulating ability of fabrics with PCM microcapsule(PCMMc), Nylon fabrics were coated with PCMMc via wet processing and they were characterized by SEM, DSC and infrared thermal analyzer. Also, water moisture transpiration, water penetration resistance, peel strength and washing durability of the fabrics were assessed. The water vapor permeation and water penetration resistance decreased with increasing PCMMc content. In DSC analysis, it can be seen that the microencapsulated fabric showed both exothermic md endothermic phenomena at specific temperature. Peel strength was decreased with increasing PCMMc content.

• 펄프종이기술
• /
• 제42권2호
• /
• pp.95-101
• /
• 2010

For the development of higher-sizing performance of paper, a sizing agent using recycled PET was synthesised. Polyester resin was extracted from wasted PET by subcritical hydrolysis and finally modified to synthetic sizing agent by mixing water-disperse PET with triphenyl phosphite(TPP). The modified PET was considered as an internal sizing agent in different wet-end papermaking conditions. The optimum condition in sizing efficiency was obtained in initial pH of 6.5 in case of rosin+alum system, and 7.5 in case of rosin+alum+PET system, respectively, and in addition amount of PET 3%. The sizing efficiency was also closely related according to the fiber properties of wet-end slurry, such as virgin fibres from UKP and recycled fibres from KOCC. The application of modified PET was good in strength improvement of paper, specially in tensile strength.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.137-140
• /
• 2006

This paper describes a technique combining chemometrics with UV spectroscopy for the determination of the concentra tions of two tissue additives (i.e., wet strength and softening agents) in a cellulose fiber containing solution. In single as ent solutions, the concentration of the additive can be measured by UV spectroscopy at the wavelength where the species having absorption. For a binary (i.e., containing two additives) solution system, the spectral characterization is very complicated. However, if aided by a chemometrical calibration technique, each additive in the binary solution can be quantified simultaneously. The present method is very rapid and simple, it can easily perform a continuous measurement in the changes in the additives' concentration after fiber addition, and therefore this becomes a valuable tool for the adsorption kinetics study of chemical additives onto the cellulose fibers. The time-dependent adsorption behaviors of the wet-strength, softening agent, and their both on fiber were also presented.