• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.602-608
• /
• 2005

We have studied to obtain the SAW filter for the Single Phase Unidirectional Transduce. (SPUDT), was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator. We can fabricate that the block weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulations. Also, we have performed to obtain the properly conditions about impedance matching of the SAW filter for SPUDT. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are 5000A and $3.6{\mu}m$, respectively. And the width of IDT' fingers is $2.4{\mu}m$, and the space between IDT' finger and reflector is $2.0{\mu}m$. Frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 7.7MHz after when we have matched impedance. Also, we could obtain that ripple characteristics is less than 0.4dB and standing wave ratio is probably 1.5 after when we have matched impedance.

• Korean Journal of Materials Research
• /
• v.11 no.10
• /
• pp.851-858
• /
• 2001

One of the important phase of black titanium oxide is $Ti_4O_7$ which has the excellent properties such as the greatest electrical conductivity among the titanium oxides, chemical resistance against acidic and alkalic conditions and electro-wave absorption etc., so it has been considered as a promising material to be used widely all over the parts of industries. In this study, $Ti_4O_7$ phase was successfully synthesized by the reaction of TiO$_2$/ Mg system. With the change of the mole of TiO$_2$to Mg, the most excellent blackness was appeared in the 3.5 mole which was the smaller amount than the stoichiometric 4.0 mole. In addition, we found that the blackness decreased as the mole ratio of reactent increased. With decreasing particle size of magnesium, blackness of titanium oxide increased. The reaction property was changed with the compaction pressure, and optimum pressure was found to be 10 MPa. At 55$0^{\circ}C$ of reduction temperature, the blackness increased as the reaction time increased. The blackness of synthesized black titanium oxide was 14 to 18, and the average particle size was 0.2 $\mu\textrm{m}$.

• Journal of the Institute of Convergence Signal Processing
• /
• v.12 no.4
• /
• pp.355-361
• /
• 2011

The power control of the existing heating element has been using the On-Off control, phase control, and PWM control. In case of controlling power PTC heating element developed recently with the existing method, the temperature is unable to be precisely controlled or the harmful electromagnetic wave to human body is generated. In this paper, We suggest the power control of PTC heating cable using variable AC Cycles. This regards the AC cycle of N as the unit of the power control. It determines On-Off for each cycle. It is the AC power control method in which it arranges the on-cycle in N cycles in the random and it supplies the current continuously. At this time. the minimal electric power amount becomes 1/N. The maximum current amount becomes 1 and sets up the number of on cycles according to the set value and can control the electric power with the step of N consistently. In the PTC heating system, we show that proposed power control method is superior in the EMI and temperature control property using MATLAB simulation, experiments and measurements.

• Tunnel and Underground Space
• /
• v.25 no.3
• /
• pp.231-243
• /
• 2015

In this study, both in-situ stress measurements and a lot of laboratory rock tests were conducted at a metal mine in Jeongseon, Korea. The stress ratio obtained from in-situ stress measurements showed a tendency to decrease according to depth below surface and its average value was 1.10. The mechanical properties such as unit weight, absorption ratio, porosity, elastic wave velocity, uniaxial compressive strength, Young's modulus, Poisson's ratio, tensile strength, shore hardness, friction angle and cohesion were investigated for the four different rocks mainly distributed at a studied mine, which were dolomite, felsite, granite and magnetite. The mechanical properties of the four different rocks were compared by means of statistical analyses, whereupon the felsite and the granite turned out to have more strength characteristics than the magnetite. The correlation of mechanical properties was also investigated, whereupon a few results against the general correlation were found out. The failure criteria of the four different rocks were finally discussed by means of both Mohr-Coulomb criterion and Hoek-Brown criterion.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.2
• /
• pp.118-128
• /
• 1999

There are many ultrasonic measurement methods that are used in nondestructive testing applications. Some typical applications include material property determination, microstructural characterization. and flaw detection. Ultrasonic parameters such as velocity and attenuation are most commonly required in these applications. The accuracy and repeatability of testing results are dependent on both the hardware used to generate and receive the ultrasonic waves and on the analysis software for calculating these parameters. In this study, five analysis algorithms were implemented on a computer for measuring wave speed in a pulse echo. immersion testing configuration. In velocity measurements comparisons were made between the overlap. cross-correlation. Fourier transform. Hilbert transform, wavelet transform algorithms. Velocity measurement was applied to an isotropic steel sample using the five analysis algorithms. Frequency-dependent phase/group velocity and attenuation were also measured using the Fourier transform and wavelet transform algorithms on a composite laminate containing voids.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.13-16
• /
• 2001

We have measured the reflectivity of superconducting infinite-layer compounds $Sr_{0.9}$ $Ln_{0.1}$ Cu $O_2$ (Ln=La, Gd, Sm) with $T_{c}$ : 39 K using a Fourier-transform infrared spectrometer. We have identified the optical phonon modes from their infrared reflectivity and conductivity spectra and have proposed possible displacement patterns. The La- and the Gd-doped compounds exhibited only four ($2A_{2u}$ $+2E_{u}$) out of the five ($2A_{2u}$ $3E_{u}$) infrared-active phonons predicted by a group theoretical analysis whereas the Sm-doped compound exhibited all five modes. For the La-doped sample, we investigated the temperature dependence of the optical response functions in a wide temperature range of 7 - 300 K. In FIR region, the reflectivity is apparently enhanced below ~120 $cm^{-1}$ as temperature decreases across $T_{c}$. The value of $2$\Delta$/k_{B}$ $T_{c}$ is about 4.5, which is consistent with maximum gap value of d-wave $high- T_{c}$ cuprates.> c/ cuprates.uprates.s.

• Textile Coloration and Finishing
• /
• v.24 no.1
• /
• pp.69-78
• /
• 2012

This paper surveys the physical properties of the MWNT dispersion solution dispersed with the three types of solvents and of the polyurethane composite film for improvement of mechanical properties and electrical characteristics of PU/MWNT composite film. For this purpose, the MWNT dispersed solution was mixed with three types of solvent such as IPA, MEK and Toluene and then mixed with polyurethane (100part) with variation of loading content (0, 10, 20, 30, 40, 50 part) of MWNT dispersed solution in the ultrasonic wave dispersion apparatus. And eighteen PU/MWNT composite films were prepared as specimens. The various physical properties of these PU/MWNT films were measured and discussed with the loading content of three types of MWNT dispersed solutions. The highest absorbancy among the three types of dispersed solutions was shown in the IPA/MWNT solution. But the absorbancy of PU/MWNT films was not same as the solution. The low electrical surface and volume resistivity of PU/MWNT film were shown at the condition of 20 and 10 parts loading of IPA/MWNT dispersed solution, respectively. The low triboelectricity of PU/MWNT film was shown at the condition of above 30part loading of IPA/MWNT dispersed solution. The breaking strength and strain of PU/MWNT film prepared with IPA/MWNT dispersed solution were decreased with increasing loading content of IPA/MWNT from 10 to 40 parts. The maximum breaking strength and breaking strain according to the dispersion solution were shown on the IPA/MWNT dispersed solution. The uniform dispersion of PU/MWNT film according to the loading content of MWNT solution was shown by surface image analysis on the films dispersed with IPA.

• Analytical Science and Technology
• /
• v.13 no.6
• /
• pp.775-780
• /
• 2000

The electrical conductivity of glass melter at high temperature has been measured. The conductivity is an important physical property for the research and the manufacturing process of glass. Because high temperature is an inconvenient situation to measure the conductivity of glass melter, we have made a platinum crucible and electrode and have measured the conductivity at high temperature. KCl solution, of which concentration is adjusted to the conductivity of glass melter, is used to get parameters of the conductivity cell. A measuring circuit is composed with an AC 1 kHz sine wave generator and an operational amplifier. The cell constants are determined from the measured voltages and the equivalent conductances of KCl solution. Various cells are tested to find a suitable shape for high temperature experiment. The results are compared by cell size, electrode depth, and cell configuration. The conductivity of the borosilicate melter is $0.053{\Omega}^{-1}cm^{-1}$ at $1,450^{\circ}C$.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.24 no.5
• /
• pp.289-302
• /
• 1991

Laboratory determination of acoustic property for unconsolidated sediment of Kwangyang Bay was carried out. The compressional wave velocity was correlated to other physical properties and sediment textures to establish a geoacoustic model of the bay. The model was compared to the North Pacific continental terrace sediment. Velocity of the bay is systematically lower(0.02-0.04km/s) than that of the North Pacific. Average velocity of the bay is 1.521km/s. The lowest velocity is measured at the southwestern part of the bay. This area coincides with high amount of fine-grained sediment related to slower circulation. The overall tendency is, however, similar to the North Pacific continental terrace sediment.

• The Journal of the Korea Contents Association
• /
• v.8 no.8
• /
• pp.244-252
• /
• 2008

This research differentiate the technique of Jungkwon-jirugi, one of the basic movements of Taekwondo, into two movements stop-jirugi and push-jirugi and gives analysis of the impulse, acceleration and velocity in the point of motor control. For this, we tried graphic analysis using an acceleration sensor and high speed camera which was made from USA in 2005 and took pictures at 250 frames per second. We reached the following conclusions. First, the acceleration wave of push-jirugi was a period longer than stop-jirugi, meaning that the push-jirugi motion asserts force for a longer time. Second, the acceleration and velocity graph shows that the highest velocity occurs on the point when the acceleration begins to decrease right after reaching its maximum. Third, according to the image analysis using the high speed camera, we could find out that the shoulder is pushed a little even in the stop-jirugi motion.