• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.5
• /
• pp.369-376
• /
• 2014

This paper presents a method that integrates passive and active-sensing techniques for the structural health monitoring of plate-like structures. Three piezoelectric transducers are deployed in a L-shape to detect and locate an impact event by measuring and processing the acoustic emission data. The same sensor arrays are used to estimate the subsequent structural damage using guided waves. Because this method does not require a prior knowledge of the structural parameters, such as the wave velocity profile in various directions, accurate results could be achieved even on anisotropic or curved plates. A series of experiments was performed on plates, including a spar-wing structure, to demonstrate the capability of the proposed method. The performance was also compared to that of traditional approaches and the superior capability of the proposed method was experimentally demonstrated.

• Structural Monitoring and Maintenance
• /
• v.4 no.2
• /
• pp.153-173
• /
• 2017

An improved method is presented to estimate the axial force of a bar member with vibrational measurements based on modified Timoshenko beam theory. Bending stiffness effects, rotational inertia, shear deformation, rotational inertia caused by shear deformation are all taken into account. Axial forces are estimated with certain natural frequency and corresponding mode shape, which are acquired from dynamic tests with five accelerometers. In the paper, modified Timoshenko beam theory is first presented with the inclusion of axial force and rotational inertia effects. Consistent mass and stiffness matrices for the modified Timoshenko beam theory are derived and then used in finite element simulations to investigate force identification accuracy under different boundary conditions and the influence of critical axial force ratio. The deformation coefficient which accounts for rotational inertia effects of the shearing deformation is discussed, and the relationship between the changing wave speed and the frequency is comprehensively examined to improve accuracy of the deformation coefficient. Finally, dynamic tests are conducted in our laboratory to identify progressive axial forces of a steel plate and a truss structure respectively. And the axial forces identified by the proposed method are in good agreement with the forces measured by FBG sensors and strain gauges. A significant advantage of this axial force identification method is that no assumption on boundary conditions is needed and excellent force identification accuracy can be achieved.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.8
• /
• pp.641-648
• /
• 2016

In this study, the effect of injection nozzle shape on the supersonic film cooling performance is analyzed using CFD. The design parameters are inside and outside angles of upper plate of nozzle and nozzle tip thickness. It is observed that the mass flow rate of film cooling decreases with increase of inside angle, while the effect of the change of mass flow rate on the film cooling effectiveness is relatively small. In addition, cooling performance is generally reduced, except ahead of the local region where shock wave interaction with film cooling occurs, in accordance with the growth of the outside angle and tip thickness. In this paper, the CFD simulation is performed using a commercial software, ANSYS Fluent V15.0, and the CFD model is validated by comparing it with the experimental data shown in preceding research.

• Journal of Powder Materials
• /
• v.20 no.5
• /
• pp.355-358
• /
• 2013

Micro trench structures are applied in gratings, security films, wave guides, and micro fluidics. These micro trench structures have commonly been fabricated by micro electro mechanical system (MEMS) process. However, if the micro trench structures are machined using a diamond tool on large area plate, the resulting process is the most effective manufacturing method for products with high quality surfaces and outstanding optical characteristics. A nonferrous metal has been used as a workpiece; recently, and hybrid materials, including polymer materials, have been applied to mold for display fields. Thus, the machining characteristics of polymer materials should be analyzed. In this study, machining characteristics were compared between nonferrous metals and polymer materials using single crystal diamond (SCD) tools; the use of such materials is increasing in machining applications. The experiment was conducted using a square type diamond tool and a shaper machine tool with cutting depths of 2, 4, 6 and 10 ${\mu}m$ and a cutting speed of 200 mm/s. The machined surfaces, chip, and cutting force were compared through the experiment.

• Journal of environmental and Sanitary engineering
• /
• v.18 no.1
• /
• pp.58-67
• /
• 2003

The characteristics of the commercial garbage-decomposing accelerant, Raw Material of Pomia(RMP), Pomia and Vitabio. were analyzed. In HPLC pattern, Pomia and Vitabio showed main peak of about 30kDa in 280nm wave length. RMP, Pomia and Vitabio showed three, two and two peaks in 210nm. K and Na ion content of RMP were 2,620 and 1,590ppm, respectively, and their content were the largest one among others. Ca, Mg and Mn ion content of RMP were also the largest one, but Zn ion content was the least one. $Cl^{-}$, $F^{-}$ and $NO_3^{-}$ ion content of RMP were the largest one, especially $Cl^{-}$ content was 3,553ppm. pH values of RMP and Pomia were in neutral region, but Vitabio was 9.03. Dried residue content of RMP, Pomia and Vitabio were 1.4%, 0.55% and 0.4%, respectively. The number of general bacteria on PCA plate from RMP, Pomia and Vitabio were 2.2{\times}10^{6}cfu/ml,{\;}6.5{\times}10^{3}cfu/ml{\;}and{\;}1.1{\times}10^{3}cfu/ml$, respectively. The number of facultative anaerobes of RMP was $4.4{\;}{\times}{\;}10^{4}cfu/ml$, and it was biggest one. Lactobacilli and yeasts were found less than 10cfu/ml at best. The bacterium exists in RMP in high frequency was identified as Bacillus subtilis. Volatile sulfur compound amount of garbage samples treated with Pomia and Vitabio in concentration of 1/500 at $33^{\circ}C$ for 8 days were 1,273ppb and 1,902ppb, respectively, and control showed 3,015ppb. Volatile organic compound amount of the garbage samples treated were 68,312ppb, 124,317ppb and 263,954ppm, respectively. Diethylamine that known as malodor compound were 5,107ppb, 261ppb and 11,124ppb, respectively.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.83-92
• /
• 1999

In this paper, the fluid-structure interaction of large floating structures has been rigorously analyzed and the shear effect on the structural deformation has been investigated in oblique waves. A constant panel method(CPM) based on the Green function method is implemented for computing the hydrodynamic pressure, while a finite element method(FEM) is applied for the structural response based on the Mindlin plate theory with including shear deformation. In order to validate the method, we compared numerical results with experimental ones of Mega Float carried out by Yago & Endo in head waves. General behavior shows good agreement but the local displacement at the ends is slightly different. The numerical results show that the radiation pressure due to the fluid-structure interaction is locally larger than that of wave excitation and mooring devices greatly reduce the response. It is observed that the shear effects among the total deformation constitutes about 4% in the case of Mega Float in oblique waves.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.561-569
• /
• 2002

Laser has been called a "Quantum Machine" because of its mechanism of generation since the development on July 7,1960.by T.H.Maiman. We can now use this machine as a tool for manufacturing in industries. At present, 45kW CO2 laser, 10kW Nd:YAG laser, 6kW LD pumped YAG laser and 4kW direct diode laser facilities are available for welding a heavy steel plate of 40mm in thickness and for cutting metals at high speed of 140m/min. Laser Materials Processing is no longer a scientific curiosity but a modern tool in industries. Lasers in manufacturing sector are currently used in welding, cutting, drilling, cladding, marking, cleaning, micro-machining and forming. Recently, high power laser diode, 10kW LD pumped YAG laser, 700W fiber laser and excimer laser have been developed in the industrialized countries. As a result of large numbers of research and developments, the modem laser materials processing has been realized and used in all kinds of industries now. In the present paper, metallurgical studies on laser materials processing such as porosity formation, hot cracking and the joint performances of steels and aluminum alloys and dissimilar joint are discussed after the introduction of laser facilities and laser applications in industries such as automotive industry, electronics industry, and steel making industry. The wave towards the use of laser materials processing and its penetration into many industries has started in many countries now. Especially, development of high power/quality diode laser will be accelerate the introduction of this magnificent tool, because of the high efficiency of about 50%, long life time and compact.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.487-494
• /
• 2011

The safety valve used in LNG/LNG-FPSO ships plays an important role in maintaining a fixed level of pressure by emitting LNG gas out of the pipes in the LNG piping system. The discharge coefficient is regarded as the most important factor in the valve performance. To satisfy the ship's classification, the discharge coefficient of the safety valve must usually be over 0.8. Despite the importance of understanding the flow phenomena inside the safety valve, the valve design is usually based on experience and experiments. We carried out a computational fluid dynamics (CFD) investigation using the ANSYS-CFX software. We observed the flow phenomena inside the valve and measured the discharge coefficients according to changes in the valve lift, which is the distance between the exit of the nozzle and the lower part of the disc plate. We verified our CFD results for the discharge coefficients using available experimental data.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.45-48
• /
• 2003

The plume interference is a complex phenomenon, consisting of plume-induced boundary layer separation, separated shear layer, multiple shock waves, and their interactions. The base knowledge of plume interference effect on powered missiles and flight vehicles is not yet adequate to get an overall insight of the flow physics in plume-freestream flow field. Computational studies are performed to better understand the flow physics of the plume-induced shock and separation for Simple, Rounded, Porous-extension test model configurations. The present study simulates highly underexpanded exhaust plume effect on missile body at the transoni $c^ersonic speeds. In order to investigate the plume-induced separation phenomenon, Simple, Rounded and Porous-extension plate are attacked to the missile afterbody. The computational result shows that the rounded afterbody and the porous-extension wall attached at the missile base can alleviate the plume-induced shock wave and separation phenomenon and improve the control of the missile body.dy.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.3
• /
• pp.281-287
• /
• 2001

For the conventional two-dimensional source location of acoustic emission (AE) based on the threshold crossing, wave velocity has to be measured in the actual structure to calculate the arrival-time difference and thus to form the two hyperbolae. Velocity is dependent on the fiber orientation, however, due to the dependence of elastic modulus on fiber orientation in anisotropic materials such as compost#e plates. This tan affect the accuracy of AE source location and make the source location procedure complicated. In this study, we propose a method to reduce the location error in anisotropic plates by using the numerical solution of nonlinear equations, where the velocity term has been removed by employing the fourth sensor. The efficiency and validity of the proposed method has also been experimentally verified.