• Journal of Ocean Engineering and Technology
• /
• v.24 no.6
• /
• pp.34-40
• /
• 2010

Bragg reflection of nonlinear waves is simulated by a 2D fully nonlinear numerical wave tank (NWT). The developed NWT was based on the Boundary Element Method (BEM) with potential theory and the mixed Eulerian-Lagrangian (MEL) time marching scheme with Runge-Kutta 4th-order time integration. A spatial variation of wave elevations and their Fourier amplitudes of each component are compared to investigate the effect of sea bottom ripples and their relative heights. The incident waves over an undulated sea bottom are partially reflected and changed to partial standing waves due to Bragg reflection. The present results are verified with linear calculations and experimental data. It is found that the 1st-order wave component is mainly affected by Bragg reflection and its spatial modulation is significant in front of the bottom ripples.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.1
• /
• pp.9-15
• /
• 2013

This paper calculates the mating dynamic forces of a semi-submersible offshore structure's topside module, where a hull moored in the sea is combined with a topside module carried by a heavy lift vessel, as a mating installation method. The environmental conditions include various wave directions and wave heights, with constant wind and current speeds. Appropriate ballast and de-ballast plans for the heavy lift vessel and hull of the semi-rig should be performed in order to safely obtain these forces, whereas a fixed platform or the GBS (Gravity based structure) type of offshore structure only needs a ballast plan for the heavy lift vessel. From this paper, the allowable wave height or wave direction for the mating procedure can be investigated based on the standard DAF (Dynamic amplitude factor) of the rules and regulations.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.2 no.2
• /
• pp.67-74
• /
• 1990

A numerical model is developed to predict the shoreline change by the coastal structures constructed. In order to describe the wave deformation at the shadow zone of the structure, the present model employs the mild-slope equation in steady state and the wave ray method using the coefficients of wave refraction, diffraction and shoaling. In the model results of shoreline changes for the various structures. it showed a qualitative agreement with the findings observed in the field such as tombolo, and the response of this model was found to be very sensitive to the longshore distribution of wave heights. It was also applied to a field area. From the results of the application this model is proved to be useful around the complex coastal structures and bottom topography.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.4 no.4
• /
• pp.243-249
• /
• 1992

Hydraulic experiments were carried out to investigate the hydraulic characteristics of solid and perforated-wall caissons of a mixed type breakwater for regular waves of various heights and periods. It was found that a perforated-wall caisson is more advantageous than a solid caisson for such hydraulic characteristics as reflection. transmission, and runup at the front face of the caissons and that the experimental results agree reasonably well with existing theoretical or empirical relationships. Especially the reflection coefficient of a perforated-wall caisson. mainly governed by the resonance in the wave chamber, was found to be minimum when the width of the wave chamber is approximately a quarter of the wave length in the wave chamber.

• Korean Journal of Remote Sensing
• /
• v.25 no.3
• /
• pp.225-231
• /
• 2009

The characteristics of morphological shapes, wave heights, tidal ranges and sediment sizes are observed and compared between intertidal beach and mudflat. The Mohang sand beach, southwest coast of Korea, is located just next to the large mudflat and has tidal range over 5 meters. Wave measurements are conducted at each entrance of the beach and mudflat as well as at the outside waters representing the incident waves to these different coastal environments. The morphological characteristics are also examined including the sediment size and the slope of the bathymetry, For the observation of morphological shapes, camera monitoring technique is used to measure the spatial information of intertidal bathymetry. The water lines moving on the intertidal flat/beach durinq a flood indicate depth contours between low and high water lines. The water lines extracted from the consecutive images are rectified to get the ground coordinates of each depth contours and integrated to provide three dimensional information of intertidal topography. The wave data show that sand beach is in the condition of severer wave forcing but tidal range is almost identical in both environment. The slope of the mudflat is much milder than the sand beach with finer sediment.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.3 s.147
• /
• pp.384-391
• /
• 2006

RCS effects of long-crested wave surfaces to marine targets are numerically analyzed using a 4-path model and a direct analysis method, developed based on physical optics and a combined method of physical optics/geometric optics, respectively. Reflectivity of long-crested wave surfaces is described with 'Fresnel reflection coefficients' The MPM(modified Pierson-Moskowitz) ocean spectrum is adopted to simulate long-crested waves in the direct analysis method. A numerical analysis of a benchmark model assures the validity of both methods. The direct analysis method is applied to the RCS calculation of electromagnetically large marine targets, which are vertically oriented or slanted to the long crested wave surfaces randomly generated with various significant wave heights. The long-crested wave surface much highly increases the RCS of the marine target, but those effects are decreased as the significant wave height grows up. At low elevation angle, the vertical model has entirely high RCS comparing slanted model, and the RCS of vertical flat plate is the highest on the calm sea surface, while those of slanted flat plates are the lowest on the calm sea surface. The RCS of marine targets on continuously-varying sea surface is more coherent at lower elevation angles, as well.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.8 no.3
• /
• pp.274-284
• /
• 2003

The analysis of wave parametric characteristics in sea regions in the vicinity of Korean Peninsula have been carried out using the third generation wave model, WAVEWATCH-III (Tolman, 1999) and four observed buoy data of Korea Meteorological Administration (KMA). Significant wave height increases about 2-3 hours later after the increase of wind speed. Maximum correlation coefficient between two parameters appears in Donghae buoy data, which is at off-shore region. When land breeze occurs, it can be found that the correlation coefficient decreases. Time differences between wind speeds and wave heights correspond to significant tidal periods at all of the buoy locations except for Donghae buoy. After verifying the WAVEWATCH-III model results by the comparing with observed buoy data, we have carried out numerical experiments near the Kuroshio current and East Sea areas, and then reconfirmed that when there exist an opposite strong current in the propagation direction of the waves or wind direction, wave height and length get higher and shorter, respectively and vice versa. It has been shown that these modulations of wave parameters are considerable when wind speed is week or mean current is relatively strong, and corresponding values have been represented.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.3
• /
• pp.163-169
• /
• 2012

In this paper, model test on the Tapdong's revetment at Jeju-si has been conducted to figure out the causes of frequent occurrence of wave overtopping and to suggest the action plan. In the model test, the reflection coefficients were measured according to the change of wave periods for with and without armor stones. Also, the wave overtopping rate and the wave pressures inside revetment structure for 4 types of upper block were estimated for various wave heights and wave periods, which are chosen based on the NE design wave with 50 year return period. It is found that the increase of the upper structure's height and the modification of the curved protruding shape are effective in reducing the overtopping rate.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.4
• /
• pp.355-367
• /
• 2004

The heat transfer and friction characteristics of the heat exchangers having sinusoidal wave fins were experimentally investigated. Twenty-nine samples having different waffle heights (1.5 mm and 2.0 m), fin pitches (1.3mm to 1.7mm) and tube rows (one to three) were tested. Focus was given to the effect of the waffle configuration (herringbone or sinusoidal) on the heat transfer and friction characteristics. Results show that the sinusoidal wave geometry provides higher heat transfer coefficients and friction factors than the herringbone wave geometry, and the difference increases as the number of row increases. The i/f ratios of the herringbone wave geometry, however, are larger than those of the sinusoidal wave geometry. Compared to the herringbone wave geometry, the sinusoidal wave geometry yielded a weak row effect, which suggests a superior heat transfer performance at the fully developed flow region. Possible explanation is provided considering the flow characteristics in wavy channels. Within the present geometric range, the effect of the waffle height on the heat transfer coefficient was not prominent. The effect of the fin pitch was also negligible. Existing correlations highly overpredicted both the heat transfer coefficients and friction factors. A new correlation was developed using the present data.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.52 no.4
• /
• pp.339-346
• /
• 2016

The aim of this research was to the experimental data using statistical and spectral analyzing method to get the motion reponses of a stern trawler in operation states such as drifting, sailing and trawling according to the wave height. In drifting, the significant and the maximum valuer of roll in beam sea increased according to the wave height, but those of pitch decreased. The response and the period of peak of roll in beam sea were increased, but those of pitch decreased. In navigation, the significant and maximum values of roll increased remarkably according to the wave height, but those of pitch changed a little. The response of roll was highest in quartering sea, beam sea and then following sea, but those of pitch was highest in bow sea, head sea and then beam sea in the order of all wave heights. The period of peak of roll due to the wave height and the wave direction changed from 3.8 to 9.9 seconds, and those of pitch changed from 3.3 to 10.4 seconds. In trawling, the significant and maximum values of roll increased a little according to the wave height, but those of pitch increased significantly. The response of roll was highest in beam sea, bow sea and then quartering sea, but those of pitch was highest in head sea, following sea, and then beam sea in the order. The period of peak of roll due to the wave height and the direction changed from 6.6 to 10.9 seconds, and those of pitch changed from 6.7 to 11.2 seconds.