• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.241-242
• /
• 2019

This technology is a water leak repair technology using composite materials of concrete structures that block leakage of structures by injecting rapid microcement into the face of underground concrete to block water and injecting flexible glycidylacrylate. Rapid micro cement system repair materials are mixed with fine fibers to improve the flexural sensitivity of the material and to form a layer that blocks stabilized water at the back of the structure by allowing rapid and tight spatial filling during injection with high cohesion The glycidylacrylate repair material can control the expansion rate, and the external stress also has the characteristic that the form of the material is not destroyed or separated, which can also be applied to vibrating induced structures that produce repetitive fatigue loads, and has an effective durability in saline, alkali, acid (chloric acid, sulfuric acid, nitric acid).

• Environmental Engineering Research
• /
• 제24권3호
• /
• pp.501-512
• /
• 2019

The seasonal effects on the biostability of drinking water were investigated by comparing the seasonal variation of assimilable organic carbon (AOC) in full-scale water treatment process and adsorption of AOC by three filling materials in lab-scale column test. In full-scale, pre-chlorination and ozonation significantly increase $AOC_{P17\;(Pseudomonas\;fluorescens\;P17)}$ and $AOC_{NOX\;(Aquaspirillum\;sp.\;NOX)}$, respectively. AOC formation by oxidation could increase with temperature, but the increased AOC could affect the biostability of the following processes more significantly in winter than in warm seasons due to the low biodegradation in the pipes and the processes at low temperature. $AOC_{P17}$ was mainly removed by coagulation-sedimentation process, especially in cold season. Rapid filtration could effectively remove AOC only during warm seasons by primarily biodegradation, but biological activated carbon filtration could remove AOC in all seasons by biodegradation during warm season and by adsorption and bio-regeneration during cold season. The adsorption by granular activated carbon and anthracite showed inverse relationship with water temperature. The advanced treatment can contribute to enhance the biostability in the distribution system by reducing AOC formation potential and helping to maintain stable residual chlorine after post-chlorination.

• 한국작물학회지
• /
• 제31권1호
• /
• pp.62-67
• /
• 1986

수확 후 3주와 8주에 맥주보리 49개 품종의 발아세, 발아율 및 수감수성의 품종간 차이를 검토하고자 실험한 결과를 요약하면 다음과 같다. 1. 수확 후 3주에 발아상의 물량 증가에 따른 발아세, 발아율, PI치와 수감수성의 차이는 컸으나 8주에는 그 차이가 적어서 휴비성이 발아세와 발아율을 저하시켰다. 2. 발아세는 휴비성이 소거된 8주에는 전 공시 품종이 극히 양호하였으며, CI 12062와 CI 15631등의 수감수성이 다소 커서 광범위한 육종재료를 교배에 이용할 경우 수감수성의 검정이 필요할 것으로 본다. 3. 수감수성은 저장기간에 관계없이 물 8ml 발아세, 발아율, PI치와 상관이 매우 높았으나 물 4ml에서는 상관관계가 없었다. 4. 저장기간, 품종 및 곡립의 풍만도에 따라서 발아세와 수감수성의 차이가 있으므로 등숙이 양호한 품종의 육성과 등숙향상을 위한 재배법이 연구되어야 할 것으로 생각된다.

• 한국석유지질학회:학술대회논문집
• /
• 한국석유지질학회 2000년도 제7차 학술발표회 발표논문집
• /
• pp.14-30
• /
• 2000

Hierarchically controlled sequence stratigraphic analysis shows that the Lower Ordovician mixed carbonate-siliciclastic Mungok Formation, Korea consists of three depositional sequences: T1, T2, and T3. Sequence boundaries are generally marked by abrupt transition from coarse-grained shallow-water carbonates to fine-grained deeper-water carbonates mixed with fine-grained siliciclastics, and show indication of subaerial exposure such as karstification. Within this sequence stratigraphic framework, facies characteristics indicate that the Mungok sequences were mostly deposited in subtidal ramp environments. High-frequency cycles consist of upward-shallowing facies successions. Cycles of shallow-water and basinal deposits are not represented well, probably due to cycle amalgamation. Cycle stacking patterns do not show a consistent thickness change that reflects a large-scale sea-level change due to unfilled accommodation space. The Mungok sequences show that many factors including relative sea-level change and topography are involved in controlling sequence development on carbonate ramps. The depositional setting evolved from the high-energy ramps in the sequences T1 and T2 into the low-energy ramp in the sequence T3. Topography is interpreted to have been responsible for the different energy regimes of the carbonate ramps in the Mungok sequences. The high ramp gradient in the sequences T1 and T2 seems to be caused by space-time-dissociated differential sedimentation resulting in spatially narrow distribution of sediment filling, which in turn may be related to high rate of relative sea-level change. In contrast, low ramp gradient was maintained in the sequence T3 during slow changes of relative sea level resulting in broad distribution of sediment filling.

• Journal of Biosystems Engineering
• /
• 제12권4호
• /
• pp.31-43
• /
• 1987

This study was performed to develop a hot water boiler system with small scale automatic rice hull furnace for the multi-purpose use in the farm. For the experiment a prototype hot water boiler system with rice hull furnace was fabricated, which was equipped with automatic hull feeder, igniter and ash removal device. Optimum operational conditions of the prototype: system were analyzed. The results arc summarized as follows. 1. The temperature measured right above the burning surface should be higher than $500^{\circ}C$ combustion. 2. The top zone of the combustion chamber was the most suitable location of the thermocouple to pick up the control temperature for the automatic operation of the rice hull furnace. 3. The content of carbon monoxide in the flue gas was increased with the filling height of burning material but it was less than 0.3 percent in volume in this experiment. When the filling height was expressed as the ratio of rice hull feed rate to the volume of the combustion chamber above the burning surface, the optimum ratio was about $150kg/m^3-h$. 4. The combustion efficiency of the prototype was higher than 95 percent when the feed rate was 1.1 to 2.3 kg/h and moisture content of rice hull was 22.4 percent (w.b.) or less. 5. It was estimated that the optimum operational conditions of the system were 1.3 to 2.0 kg/h in feed rate, 70 to 100 percent in excess air and 500 to $510^{\circ}C$ in control temperature. 6. The efficiency of coil heal exchanger increased with a decrease in feed rate of rice hull. When the rice hull feed rates were 1.1, 1.7 and 2.3 kg/h, the efficiencies of coil heat exchanger were about 34, 30 and 25 percent and heat transfer rates were 5.7, 7.6 and 8.8 MJ/h, respectively. When the flat plate heat exchanger was used in addition to the coil heat exchanger, the efficiency of the heat exchanger system increased to 48 percent.

• Nuclear Engineering and Technology
• /
• 제49권3호
• /
• pp.476-483
• /
• 2017

The decay heat that is produced by nuclear reactor spent fuel must be cooled in a spent fuel storage pool. A wickless heat pipe or a vertical two-phase closed thermosyphon (TPCT) is used to remove this decay heat. The objective of this research is to investigate the thermal performance of a prototype model for a large-scale vertical TPCT as a passive cooling system for a nuclear research reactor spent fuel storage pool. An experimental investigation and numerical simulation using RELAP5/MOD 3.2 were used to investigate the TPCT thermal performance. The effects of the initial pressure, filling ratio, and heat load were analyzed. Demineralized water was used as the TPCT working fluid. The cooled water was circulated in the water jacket as a cooling system. The experimental results show that the best thermal performance was obtained at a thermal resistance of $0.22^{\circ}C/W$, the lowest initial pressure, a filling ratio of 60%, and a high evaporator heat load. The simulation model that was experimentally validated showed a pattern and trend line similar to those of the experiment and can be used to predict the heat transfer phenomena of TPCT with varying inputs.

• 한국물환경학회지
• /
• 제37권5호
• /
• pp.363-368
• /
• 2021

On the assessment results of the non-point source pollutant removability of bio-block using waste sewage sludge, at the reactor's initial operation stage, the removal efficiency of COD was slightly unstable. However, after the reactor was stabilized, the COD removal efficiency was higher in the reactor filled with bio-blocks compared to the reactor filled with broken stones. In terms of nitrogen and phosphorus, their removal efficiency was unstable at the initial stage of the reactor operation. This phenomenon was investigated through the bio-block elution experiments. Results indicated that nitrogen and phosphorus were eluted from the bio-blocks affecting their removal at the initial operation. Furthermore, based on elution tests conducted after the dry ashing of the waste sewage sludge, part of the nitrogen and phosphorus was eluted similar to the bio-block elution test results, although considerable amounts of nitrogen and phosphorus were reduced compared to the sludge cake. Prior to the use of the waste sewage sludge bio-blocks as a filter medium to remove non-point source pollutants, a stabilization period of 10 days was required. After the stabilization process, results showed similar characteristics as general aggregates. Moreover, to use the bio-block as a filter medium for the non-point pollutant removal, the filling ratio of 75% was the most suitable as it resulted in the highest nitrogen removal efficiency after the stabilization. The results of this study suggested that waste sewage sludge can be suitably recycled as a mixed raw material for the bio-blocks, with satisfactory application as a filter medium in artificial wetlands, stormwater runoff problems, stream water pollutants to eliminate non-point source pollutants.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2008년도 학술발표회 논문집
• /
• pp.1438-1441
• /
• 2008

Throughout the history, the people of Iran have battled the dryness by innovations to preserve every drop of water that lands from the rare clouds, or from a stream flowing out of distant springs. Water is precious and held with highest respect, whether stored for drinking at an Ab-Anbar, or for washing and farming at the Houz in the middle of their oasis homes and orchards, or sourced at a Qanat spring or Jooy under ground. How it is that drinking water as cold as a mountain fall is found in desert of Iran? Ab-Anbar is an ancient means of water preservation and cooling through anunderground building structure. These underground structures have been present in Khorasan and other desert provinces of Iran as public or private water storage facilities, widely used before the installation of public plumbing systems in the late 1950s. Although many of these structures are still functional, most have been protected by government for restoration or viewing by the public as historical heritage. Khorasan natural dry climate and the massive surrounding deserts have been a breeding ground for many designs of Ab-Anbars. Today the existing number of such facilities stands in the province of Khorasan. Usually these structures were built in populated areas, also there are some forms of such structures on old trade routes and roadways leading to and from populated towns. This paper considers the history of Ab-Anbars in Khorasan as well as other relevant aspects such as types, components, construction methods and materials, filling and withdrawal systems.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.1025-1028
• /
• 2009

Earth and rock fill dam is our typical dam because of their inherent flexibility and adaptability to various fundation conditions. In order to secure structural safety, rockfill materials are used angular particles obtained by blasting parent rock or rounded particles collected from river beds. Concrete-faces rockfill dams(CFRD) and Concrete-faces gravelfill dams(CFGD) have become popular in the last 20 years as s result of their good performance and low cost compared with the rockfill dam. These Dams are also constructed by the materials. A key factor in the design of the dams is the deformations induced during construction and upon reservoir filling. These can be predicted using the stress-strain and strength properties can be adequately define. However the stress-strain properties of rockfill are difficult to determine because the properties are affected by such factors as particle grading, size and shape of particles, stress conditions, and particle crushing. In our study, testing of the behavior of the rockfill materials are essential prerequisites to the realistic analysis and design of the CFGD. This paper deals with laboratory testing of particle crushing among the study.

• 한국통신학회논문지
• /
• 제33권2A호
• /
• pp.107-114
• /
• 2008

무선 접속 시스템에서는 주파수 선택적 페이딩 환경에서 직교 주파수 분할 다중화 기법 (OFDM)의 성능을 향상시키기 위한 연구가 많이 진행되었다. 시불변 채널을 송수신단 모두 알고 있는 경우, 워터 필링 (water-filling) 기법을 이용한 적응변조 기법이 최적이라고 증명되었다. 하지만, OFDM 시스템에서는 워터 필링 기법은 모든 부채널에 대한 채널정보를 송신단으로 보내기 위한 방대한 양의 오버헤드를 필요로 하게 된다. 본 논문에서는 제한된 궤환정보를 이용한 하항링크 적응변조 및 부호화 기법에 대해 제안하고자 한다. 궤환정보의 양을 최소화하기 위해서 각 부채널에 대한 채널정보 대신 하나의 OFDM 심볼을 기준으로 한 적응변조 방법을 적용한다. 궤환정보의 양이 대폭 감소되었지만, 성능열화 정도는 2dB 보다 적게 나타남을 모의실험을 통해 확인하고자 한다. 또한, OFDM 시스템에서는 부채널들을 그룹화하여 다중사용자 환경에서 사용될 수 있다. 이러한 다중사용자 환경에서는 본 논문에서 제안하는 기법의 전송률이 부채널 그룹이 증가할수록, 그리고 사용자가 많아질수록 채널용량에 근접함을 보여주고자 한다.