• Journal of the Korean Society of Safety
• /
• v.20 no.2 s.70
• /
• pp.105-112
• /
• 2005

This is to find out that cement mortar mixed with waste tie particle can be applied for recycling it and enhanced to have shock absorption capacity. Therefore, architectural material specification and its related references for the disposal of it are based on for the study. Test has been performed with procedure, based on the Korea Standard insulation mortar and Compressive Strength Test has been done at K remicon factory approved by Korea Government in Korea, in order to decrease any possible error in mixing procedure. Test molds far insulation capacity and cohesive strength have been delivered to the expert agency for having more exact results. The result from the above test shows that waste tyre mixed with cement mortar has almost equal to the common concrete. This means that the recycling of the waste t)re will be demanded more and more in case of having continued development for this recycling area. And also waste t)to-using construction material can be more applied for construction area than existing material. Thus, this recycling method can be very usefully applied for solving environmental problem and for establishing economic aspect.

• Resources Recycling
• /
• v.20 no.5
• /
• pp.16-33
• /
• 2011

Waste electrical and electronic equipment(WEEE or E-waste) is one of the fastest growing waste stream in Korea. The proper management of such equipment has become of major concern for solid waste professionals because of the large growth of the waste stream and the presence of a myriad of toxic materials with in it. In this paper in order to review the recycling system and recycling industries of the E-waste in Korea, the main frame concerning recycling of "Act on the Resources Recycling of Waste Electrical Electronic Equipment(WEEE) and End-of-life vehicles", recycling system, current recycling status, estimation of the E-waste generation, material flow of the E-waste, economics of PCB and recycling industries of the E-waste were surveyed.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.214-214
• /
• 2006

The huge amounts of wastes were produced nowadays. Among the solid waste stream, the waste plastic portion is about 20 % in weight, over 50 % in volume. But the most of waste plastics were incinerated or land filled. Only a bit of waste plastics were recycled and reused. On the view point of current energy crisis, this will be an extravagance of beneficial resource. So we should consider the waste plastics as a beneficial raw material. Also need to develop the field of reusing and recycling of post-consumed plastic. In this context, present paper describes the methodology for enhancing or improving the specific properties by way of using inorganic filler waste. Also develop the product from these post-consumed plastic.

• Resources Recycling
• /
• v.30 no.1
• /
• pp.53-59
• /
• 2021

Waste vinyl generated from household waste has been used as a solid refuse fuel (SRF) due to the presence of impurities such as soil, metal, and glass; however, the amount of SRF used has been decreasing owing to recent environmental problems, thereby necessitating the need for recycling. In this study, the mixed recycled raw material produced from household waste vinyl and polyethylene (PE) single recycled raw material produced from agricultural waste vinyl were examined. Raw material analysis revealed that waste vinyl was mainly composed of polyethylene, and approximately 2% of ash remained in the mixed recycled raw material, whereas no ash was found in the PE single recycled raw material. In addition, the analysis of tensile strength according to the mixing ratio of the two recycled raw materials revealed that the highest tensile strength was approximately 16 MPa under the heat treatment temperature of 200 ℃, compression pressure of 30 MPa, and a mixing ratio of 3:7 (mixed:PE single). In addition, the highest bending strength was approximately 39 MPa under the heat treatment temperature of 200 ℃, compression pressure of 30 MPa, and a mixing ratio of 3:7 (mixed:PE single). Therefore, the possibility of recycling waste vinyl was suggested by investigating the change in strength characteristics according to the mixing ratio of the recycled raw materials.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.528-535
• /
• 2000

Solid waste incinerator is expected to become widely used in Korea. The incineration of solid waste produces large quantities of bottom and fly ash, which has been disposed of primary by landfilling. However, as landfills become undesirable other disposal method are being sought. In this study, an experimental research is conducted to determine the geotechnical properties of municipal solid waste incinerator fly ash(MSWIF) in order to evaluate the feasibility of using the material for geotechnical applications. Basic pysicochemical characteristics, moisture-density relationship, strength, permeability, and leaching characteristics are examined. The results of MSWIF are compared to other MSWIF and coal fly ash which are used as construction material. In addition, the effectiveness of cement stabilization is investigated using various mix ratios. The result of stabilized mixes are compared to the unstabilized material. Cement stabilization is found to be very effective in reducing permeability, increasing strength, and immobilizing heavy metals. This results indicate that MSWIF with cement stabilization may be used effectively for geotechnical application.

• Journal of Korea Foundry Society
• /
• v.15 no.5
• /
• pp.477-482
• /
• 1995

A computer simulation model of various smelting process for melting waste sand was developed by using energy and material balance concept. This model can predict the coal, flux and oxygen consumption and the volume and temperature of off-gas. The major critical variables for smelting process can be explained by using the analysis of energy and material balance. The major conclusions were as follows; 1. The most important variables for smelting process were high post-combustion ratio, high heat transfer efficiency and refractory protection technology. 2. For saving energy in this smelting process, selection of raw materials i.e coal, flux are very important, espacially using of low volatile coal is very profitable. 3. The treatment cost of waste sand is high and environmental restriction is severe, in this reason we must be concerned in the treatment of waste sand by smelting process.

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2704-2710
• /
• 2024

Nuclear archaeology research provides scientific methods to reconstruct the operating histories of fissile material production facilities to account for past fissile material production. While it has typically focused on analyzing material in permanent reactor structures, spent fuel or high-level waste also hold information about the reactor operation. In this computational study, we explore a Bayesian inference framework for reconstructing the operational history from measurements of isotope ratios from a sample of nuclear waste. We investigate two different inference models. The first model discriminates between three potential reactors of origin (Magnox, PWR, and PHWR) while simultaneously reconstructing the fuel burnup, time since irradiation, initial enrichment, and average power density. The second model reconstructs the fuel burnup and time since irradiation of two batches of waste in a mixed sample. Each of the models is applied to a set of simulated test data, and the performance is evaluated by comparing the highest posterior density regions to the corresponding parameter values of the test dataset. Both models perform well on the simulated test cases, which highlights the potential of the Bayesian inference framework and opens up avenues for further investigation.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.12
• /
• pp.75-79
• /
• 2012

In the recycling of industrial waste unlike household waste, the legislation and the governmental systematic support, etc. were not also established due to an anxiety of hazard or harmfulness, etc. and a preconception. So the legislation and the system should be urgently established for the recycling of industrial waste. In this study, the environmental analyzing method of industrial waste-mixed coal ash in ash pond to recycle as a construction material is suggested by considering and analyzing test process and results about environmental impact factors of mixed coal ash. It is certified that there are not environmental problems in the recycling of mixed coal ash in ash pond as a construction material, according as its classification is general waste and each corresponding item of the leaching test result are satisfied with the 'environmental safety criteria' suggested in this study. And to build database, it is necessary to survey the environmental impact on surrounding areas with time after its recycling as a construction material.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.22 no.2
• /
• pp.185-199
• /
• 2024

Disposal cover as an engineered barrier of a near-surface disposal facility for low and very low-level radioactive waste is composed of a multi-layer to isolate radioactive waste from environmental influences for the long term. To acquire a realistic forecast for the post-closure period of the disposal facility, it is essential to carry out long-term experimental research in a similar condition to the actual disposal environment. Hence, a performance test facility of the disposal cover was constructed in Gyeongju low and intermediate level radioactive waste disposal center in 2022. The constructed performance test facility has differences from the material properties presented in the design. These differences are factors that affect the prevent rainfall infiltration, which is one of the important roles of the disposal cover. Therefore, in this study, a numerical simulation of rainfall infiltration into the performance test facility was performed for the designed case and the actual constructed case. To simulate the behavior of water infiltration, the FEFLOW software based on the finite element method is used. Through the analysis of numerical simulation results, it is confirmed that the hydraulic conductivity of the material constituting the multi-layer of the disposal cover greatly influences the amount of water infiltration.

• Resources Recycling
• /
• v.22 no.6
• /
• pp.33-40
• /
• 2013

Due to the environmental problem caused by plastics largely used in various fields, the importance of recycling is being emphasized. A research on material separation of ABS and PS mixed plastic waste, using a triboelectrostatic separator, was carried out for recovery the ABS. As a results of research on charging characteristic for choosing charging material, it was confirmed that ABS was optimum charging material for a tribo-charger in the material separation of ABS and PS. In the material separation using ABS charger, ABS grade of 99.5% and recovery of 92.5% were achieved at 20 kV, splitter position +2 cm from the center and 30% relative humidity. Therefore, material separation technique for recycling ABS and PS mixed plastic waste was established.