• Journal of the Korean Geotechnical Society
• /
• v.22 no.2
• /
• pp.19-28
• /
• 2006

Long-term field observations were performed in three excavation sites in order to investigate the displacement behavior of adjacent ground during overall excavation procedure, where the depths of deep excavations were 15 m$\∼$29 m. In this study, ground settlements and lateral displacements of braced wall measured during installation of retaining wall and removal of bracing were specially focused to evaluate the behavior quantitatively according to three-stage-divided procedure, i.e. pre-excavation, main excavation, and removal of bracing. Through field measurements on three excavation sites, lateral displacements induced during removal of bracing are approximate to 40$\%$ of the amount found during main excavation stage and additional adjacent ground deformation during post-excavation procedure ranges from 18$\%$ to 33$\%$ of that found during main excavation stage, based on the settlement volume. In conclusion, it was quantitatively identified in this study that the deformations of adjacent ground during pre- and post-excavation stage were not negligible.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.12
• /
• pp.77-88
• /
• 2006

A series of model tests were performed to investigate the ground deformation during trench excavation for diaphragm walls. An apparatus was manufactured to observe the failure pattern of a slurry-supported trench in sandy ground. Ground deformations including settlement and lateral displacement of the surrounding ground adjacent to the trench were carefully monitored during excavation. Experimental observations indicated that the settlement of the adjacent ground increased with closing to the trench. Especially, the considerable settlement occurred at the distance which was equal to 40% of the excavation depth. And, the higher settlement was obtained when the relative density of ground was looser and the ground water table was higher. Also, the lateral wall face of excavated trench was bulged with lowering the slurry level In stages and then the upper part of trench failed finally. The envelope of ground surface settlement could be represented as a hyperbolic line and the measured settlement was smaller than those predicted by Clough and O'Rourke (1990).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4C
• /
• pp.239-245
• /
• 2006

The steep slopes have been increased of new roads, industrial site development and large scale residential development. The preservation administration and steep slope construction are currently investigated by many researchers in Korea. However, concrete retaining wall or reinforced soil (i.e. Block or Pannel) are being applied for the steep slope, which results in the front face form of the structure being limited. This research investigates the method that can make up afforestation environment-friendly circumstances during the construction of steep slope structure. It is considered that steep slope reinforced structure would be possible based on the monitoring results about earth pressure, horizontal displacement and consolidation quality generated during the construction of whole constructing reinforced structure. Also, there no problems in grassy surface, drainage, and deformation in spite of rainy season after construction period and until now. So that the seeding soil layer surface reinforced soil method could be adopt for steep slope reinforced structure and others.

• Journal of the Korean Geosynthetics Society
• /
• v.23 no.2
• /
• pp.29-42
• /
• 2024

The 2017 Pohang earthquake caused damage to quay structures due to liquefaction. Liquefaction occurs when effective stress is lost due to an increase in excess pore water pressure during an earthquake. As a result, the damage caused to the pier-type quay wall was identified and the damage caused by liquefaction was analyzed. In addition, in the case of improved ground, damage occurred due to liquefaction of the lower sand layer due to the difference in stiffness from the soft rock layer, so additional numerical analysis was performed assuming non-liquefaction ground. There are several factors that affect the increase in excess pore water pressure ratio, such as the relative density of the ground and the magnitude of the input seismic acceleration. Therefore, this study performed numerical analysis for Cases 1 to 3 by increasing the magnitude of the input acceleration, and in the case of improved ground, damage occurred due to liquefaction of the lower sand layer, so the analysis was performed assuming non-liquefaction ground. As a result, the improved ground requires additional reinforcement when there is liquefied ground below, and the horizontal displacement of the pier-type quay piles was reduced by about two times.

• Journal of Navigation and Port Research
• /
• v.48 no.4
• /
• pp.303-309
• /
• 2024

This study examines the effects of wave pressure on a vertical wall due to armor block failure at the front of a caisson, using a 2-D hydraulic model to simulate three types of armor block cross-sections. Additionally, the hydraulic characteristics of two cross-sections that replicated the armor blocks' failure, based on complete cross-sections, were compared. Moreover, quantitative analysis indicated that in the cross-section where the displacement of the armor block was recreated, wave run-up( ) increased by an average of 73%, the sum of dimensionless wave pressures increased by 28%, and converted wave force rose by 33%. These findings underscore the need for countermeasures in the event of armor block failure.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.428-446
• /
• 1997

Restorative procedures can lead to weakening tooth due to reduction and alteration of tooth structure. It is essential to prevent fractures to conserve tooth. The resistance to fracture of the restored tooth may be influenced by many factors, among these are the cavity dimension and the physical properties of the restorative material. The placement of direct composite resin restorations has generally been found to have a strengthening effect on the prepared teeth. It is the purpose of this investigation to study the relationship between the cavity isthmus and the fracture resistance of a tooth in composite resin restorations. In this study, MO cavity was prepared on maxillary first premolar. Three dimensional finite element models were made by serial photographic method and isthmus(1/4, 1/3, 1/2 of intercuspal distance) were varied. Two types of model(B and R model) were developed. B model was assumed perfect bonding between the restoration and cavity wall and R model was left unfilled. A load of 500N was applied vertically at the first node from the lingual slope of the buccal cusp tip. This study analysed the displacement, 1 and 2 direction normal stress and strain with FEM software ABAQUS Version 5.2 and hardware IRIS 4D/310 VGX Work-station. The results were as follows : 1. Displacement of buccal cusp in R model occurred and increased as widening of the cavity, and displacement in B model was little and not influenced by cavity width. 2. There was a significant decrease of stress resulting in increase of fracture resistance in B model when compared with R model. 3. With the increase of the isthmus width, B model showed no change in the stress and strain. In R model, the stress and strain increased both in the area of buccal-pulpal line angle and the buccal side of marginal ridge, therefore the possibility of crack increased. 4. The stress and strain were distributed evenly on the tooth in B model, but in R model, were concentrated on the buccal side of the distal marginal ridge and buccal-pulpal line angle, therefore the possibility of fracture increased.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.10
• /
• pp.33-47
• /
• 2017

A self-supported temporary excavation method called IER is normally applicable to excavation depth ranging from 6.0 m to 7.0 m though the method depends on ground condition and overburden load. Combining IER with another method is required in deeper excavation depth in order to maintain the structural stability of the IER. In this study, we performed model tests and 3D FE analysis to check the stability of the IER adopting soil nailing method, and to propose its effective installation method. The lateral displacement of the IER using soil nailing decreased by 92% of that of IER without soil nailing. Optimum design is possible for both economic feasibility and stability when interval spacing and length of soil nails is $1.5m(S_h){\times}0.75m(S_v)$ and 86% of excavation depth, respectively. Excavation depth using IER increases 1.71 times by adopting soil nailing in increment of lateral displacement of IER right before the last excavation stage.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.25 no.2
• /
• pp.399-408
• /
• 1995

The purpose of this study was to obtain information on the clinical and radiographic features of the dentigerous cysts in the jaws. For this study, the authors examined and analysed the clinical records and radiographs of 233 patients who had lesions of dentigerous cyst diagnosed by clinical and radiographic or histopathological examinations. And the obtained results were as follows: 1. Dentigerous cysts occurred the most frequently in the 2nd decade(38.2％) and occurred more frequently in males(67.4％) than in females(32.6％). 2. The most common clinical symptom was swelling of the jaw(33.9％), and the lesions were treated by the method of surgical removal. 3. The type of lesions was mainly observed as central type(72.5％), and size of the lesion was most frequently observed 2 - 2.9cm in the widest length. 4. The lesions were most frequently observed well-defined outline with hyperostotic border(49.8％), and smooth margin(73.4％), and homogeneous lesional radiolucency(79.4％). 5. Cortical thinning and expansion of the lesions(82.0％) were observed, and their direction were most frequently observed toward buccal side(64.0％). 6. The effect on the causative tooth were observed as tooth displacement(41.2％) and delayed root development(l9.3％), and the distance between cemento-enamel junction and lesional wall attachment of the causative tooth was mainly observed as below 2mm(79.6％). 7. The effect on the adjacent tooth were observed as loss of lamina dura(66.8％), root resorption(33.9％), and tooth displacement(31.5％). 8. The effects on the adjacent anatomic structures were observed as displacement of the mandibular canal(46.5％) and maxillary sinus or nasal cavity(72.2％).

• International Journal of Aeronautical and Space Sciences
• /
• v.12 no.2
• /
• pp.149-155
• /
• 2011

The viscous flow in an axisymmetric nozzle was analyzed while accounting for the mesh sizes in both in the free stream and the boundary layer. The Navier-Stokes equations were resolved using the finite volume method in order to determine the supersonic flow parameters at the exit of the converging-diverging nozzle. The numerical technique in the aforementioned method uses the flux vector splitting of Van Leer. An adequate time stepping parameter, along with the Courant, Friedrich, Lewis coefficient and mesh size level, was selected to ensure numerical convergence. The boundary layer thickness significantly affected the viscous flow parameters at the exit of the nozzle. The best solution was obtained using a very fine grid, especially near the wall at which a strong variation of velocity, temperature and shear stress was observed. This study confirmed that the boundary layer thickness can be obtained only if the size of the mesh is lower than a certain value. The nozzles are used at the exit of the shock tube in order to obtain supersonic flows for various tests. They also used in propulsion to obtain the thrust necessary to the displacement of the vehicles.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.452-458
• /
• 2007

The vertical extension of a building in general remodeling process increases both gravity and seismic loads by simply adding masses to the building. In this study, a vertical extension structural module (VESM) is proposed for enhancing seismic performance of the existing buildings by utilizing the story-increased parts. The proposed VESM is composed of steel column, steel beam, and beam-end rotational damper. The steel columns are connected to the shear walls and transfer the wall rotation in out-of plane to the steel beam, and then the beam-end rotational damper dissipates the earthquake-induced energy. Numerical analysis result from a cantilever beam of which end-rotation is restricted by rotational damper indicates that the displacement, base shear, and base overturning moment of the existing structures showing cantilever behavior can be significantly reduced by using the proposed method. Also, it is observed that friction-type rotational damper is effective than viscous one.