• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.514-519
• /
• 2003

The objective of this study is to document the secondary flow and the total pressure loss distribution in the contoured endwall installed linear turbine nozzle guide vane cascade passage and to propose an appropriate contraction ratio of the contoured endwall which shows the best loss reduction among the simulated cases. In this study, three different contraction ratio of contoured endwalls have been tested. This study was performed by experimental method and when the contoured endwall has the contraction ratio of 0.17 on exit height the results showed the best loss reduction.

• 한국안전학회지
• /
• 제4권1호
• /
• pp.59-70
• /
• 1989

This paper deals with the experimental study on the flow characteristics in straight flow can type combustor which has been used for high pressure ratio gas turbine combustor. The author has investigated the effects of swirl number and secondary air hole arrays in axial position on the flow characteristics by adopting the tuft method and 5-Hole Pilot Tube. From these experiments, as the swirl number increases, the results obtained is that the area of recirculation zone becomes wide and the position of vortex-core region approaches to the near of fuel nozzle in the model combustor. The most favourable penetration is obtained when secondary air jet is introduced through the air holes distributed in the form of paralled two rows in axial position of model combustor.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.63-66
• /
• 2008

The bridge deck section composed of a concrete slab resting on two I-beam girders are known to be susceptible to flutter instability and vortex shedding. Moreover, the cable stayed bridge in construction is more vulnerable to wind rather than in service when the free cantilever construction method is applied. This paper describes the effect of the dynamic wind loads on the bridge during construction and the effect of alternative temporary stabilizing measures. Therefore, a series of wind tunnel tests and numerical analysis were carried out to determine if any countermeasures were required.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.13-19
• /
• 2009

The spools in most hydraulic spool type control valve have several circumferential grooves to pre-vent well known hydraulic locking problems which result in high friction force and excessive wear. In this paper, a commercial computational fluid dynamics (CFD) code, FLUENT is used to investigate the flow and lubrication characteristics of grooved hydraulic spool valve. The stream lines and pressure distributions are obtained for various groove cross sectional shapes and film thicknesses. The stream lines are highly affected by groove cross sectional shape but pressure distributions mainly depend on the film shape and its magnitude. Therefore the numerical method adopted in this paper and results can be use in designing of various grooved spool valve.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 춘계학술대회 논문집
• /
• pp.52-57
• /
• 2001

Laminar two-dimensional time-dependent flow past a circular cylinder is numerically investigated using direct numerical simulation for the low Reynolds number (Re=164∼280). The higher-order finite difference scheme is employed for the spatial distributions along with the second order Adams-Bashforth and the first order backward-Euler time integration. The convection term is applied by the 7th order up wind scheme and the pressure and viscosity terms are applied by the 4th order central difference. The grid system makes use of the regular grid system and it is generated by an equation. The calculated results of drag coefficients, lift coefficients, pressure distributions, and vorticity contours and other information are compared with experimental and numerical ones. These results obtained by the present DNS show good agreement with the previous studies.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 춘계학술대회 논문집
• /
• pp.117-121
• /
• 2001

A numerical simulation was conducted to investigate the effect of height position of Rushton type Impeller in the fermentation. The computational method was based on the CFX code. The simulation was performed for 3 height differences(25, 30, 35mm) between Rushton type impeller and bottom of fermentation. The instantaneous flow fields showed that the bulk flow consisted of large scale vortices. However the main flow results showed that the formation of ring vortices above and below the impeller depended on the height of the impeller.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.113-116
• /
• 2002

The shock wave discharged from an annular duct leads to very complicated flow features, such as Mach stem, spherical waves, and vortex rings. In the current study, the merging phenomenon and propagation characteristics of the shock wave are numerically investigated using a CFD method. The Harten-Yee's total variation diminishing (TVD) scheme is used to the unsteady, axisymmetric, two-dimensional, compressible Euler equations. The Mach number of incident shock wave $M_s$ is varied in the range below 2.0. The computational results are visualized to observe the major features of the annular shock waves discharged from the tube. On the symmetric axis, the peak pressure produced by the shock wave and its location depend upon strongly the radius of the annular tubes. A Mach stem is generated along the symmetric axis of the annular tubes.

• 한국기계기술학회지
• /
• 제13권4호
• /
• pp.57-62
• /
• 2011

In this study, a experimental work to investigate the influence of a turbulent wake flow on the velocity distribution of a diffuser with PIV method. The turbulent wake is generated by a rectangular prism, which is installed at the inlet of a diffuser. The results show that the velocity recovery of the subsonic diffuser is dependent on the height and location of rectangular prism. It is found that a certain height of the rectangular prism to generate the turbulent wake give a better velocity recovery, compared with no rectangular prism.

• Advances in aircraft and spacecraft science
• /
• 제6권5호
• /
• pp.371-389
• /
• 2019

The implementation of a robust $H_{\infty}$ Control, which is numerically efficient for uncertain nonlinear dynamics, on longitudinal and lateral autopilots is realised for a quarter scale Piper J3-Cub model accepted as an unmanned aerial vehicle (UAV) under the condition of sensor noise and disturbance effects. The stability and control coefficients of the UAV are evaluated through XFLR5 software, which utilises a vortex lattice method at a predefined flight condition. After that, the longitudinal trim point is computed, and the linearization process is performed at this trim point. The "${\mu}$-Synthesis"-based robust $H_{\infty}$ control algorithm for roll, pitch and yaw displacement autopilots are developed for both longitudinal and lateral linearised nonlinear dynamics. Controller performances, closed-loop frequency responses, nominal and perturbed system responses are obtained under the conditions of disturbance and sensor noise. The simulation results indicate that the proposed control scheme achieves robust performance and guarantees stability under exogenous disturbance and measurement noise effects and model uncertainty.

• 대한조선학회논문집
• /
• 제31권2호
• /
• pp.45-56
• /
• 1994

2차원 수중익 주위의 비선형 자유표면 유동을 시간영역에서 시뮬레이션할 수 있는 수치해법이 개발되었다. 본 수치해법은 고차 스펙트럴법과 경계요소법을 조합한 스펙트럴/경계요소법(spectral/boundary-element method)이며, 자유표면은 고차 스펙트럴법에 의해 그리고 수중익과 후류 보오텍스는 경계요소법에 의해 다루어 진다. 본 방법은 자유표면과 수중익의 비선형/비정상 상호작용문제에 폭넓게 적용될 수 있으며, 특히 스펙트럴법을 사용하므로 자유표면 유동을 매우 효율적으로 다룰 수 있다. 적용예로 정지상태에서 출발하여 자유표면 근처에서 균속 전진운동 또는 전진 및 동요운동을 하는 경우가 다루어 졌고, 자유표면파와 동유체력에서의 비선형/비정상 효과들이 보여지고 있다. 비정상해의 특수한 경우로 얻어지는 정상상태의 계산결과들이 다른 이론 또는 실험결과들과 비교되었으며, 좋은 일치를 보이고 있다.