• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.476-479
• /
• 1997

The focus of this paper is to implement of virtual plant using module concept for the dynamic simulation of drum type boiler and to simulate the control trends of dynamic characteristics. MAtlab & Simulink is used for implement virtual plant & analyzation the dynamics & control trends. They are available for analyzing the dynamic characteristics of drum type Boiler by means of applying well measured data to virtual plant.

• Proceedings of the IEEK Conference
• /
• 2009.05a
• /
• pp.76-78
• /
• 2009

This paper considers the problem of global adaptive regulation for a class of nonlinear systems which have multiple unknown virtual control coefficient. By using a new parameter estimator and backstepping technique, we design a smooth state feedback control law, parameter update laws that estimate the unknown virtual control coefficients, and a continuously differentiable Lyapunov function which is positive definite and proper.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.1
• /
• pp.54-60
• /
• 2020

A digital current control scheme using virtual d-q transformation for a boost single-phase power factor correction (PFC) converter is proposed. The use of virtual d-q transformation in single-phase power converters is known to improve current control performance. However, the conventional virtual d-q transformation-based digital current control scheme cannot be directly applied to the boost single-phase PFC converter because the current and average voltage waveforms of the inductor used in the converter are not sinusoidal. To cope with this problem, this study proposes a virtual sinusoidal signal generation method that converts the current and average voltage waveform of the inductor into a sinusoidal waveform synchronized with the grid. Simulation and experimental results are provided to show that the virtual d-q transformation-based digital current control is successfully applied to the boost single-phase PFC converter with the aid of the proposed virtual sinusoidal signal generation method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.341-341
• /
• 2000

This paper presents a sliding mode control(SMC) design method for single input linear systems with uncertainties and time delay in the state. We define a sliding surface for the augmented system with a virtual state which is defined from the nominal system. We make a virtual state from optimal control input using LOR(Linear Quadratic Regulator) and the states of the nominal system. We construct a controller that combines SMC with optimal controller. The proposed sliding mode controller stabilizes on the overall closed-loop system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.8
• /
• pp.709-712
• /
• 2015

This paper will introduce the development case study about virtual-reality-based operation training system for steel making process. Steel making process consist iron making process to create liquid steel, pig iron, by reduction process, steel making process to make molten steel by refining, continuous casting process to make slab, and rolling process to make final product like coil, plate. This steel making process deals with liquid and solid products, so facilities of steel making process are very various and complicated. In addition, according to various customer requirements, the recycle of facilities and recipes changing have been fast. So the training for skilled operators is very important point. In this paper, we develop steel making training system based virtual reality for training skilled operator. This system consists of virtual machine, virtual HMI, and virtual control panel. And for fitting the characteristics of each process and increasing the education effectiveness, we develop dynamic methods like the method of dynamic education system configuration, initial facilities setup operation education system, and etc.

• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1338-1347
• /
• 2015

DC injection is a critical issue in transformerless grid-connected inverters. DC injection control based on virtual capacitor has the advantages of low cost, low loss, high accuracy and easy implementation. In this paper, the principle of DC injection control based on virtual capacitor was analyzed. In addition, the applicable conditions, working process, steady state error and advantages were also discussed in detail. The design of the control parameters based on virtual capacitor was proposed in a grid-connected inverter with LCL filter. The robustness of the control parameters was also discussed. Simulation and experimental results verify the validity of the analysis and demonstrate that this research has a certain value in engineering applications.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.76-91
• /
• 1996

In this paper, we proposed the new medium access control protocol for the virtual token bus netowrk. The network is applied to inter-processor communication network of large capacity digital switching system and digital mobile system with distributed control architecture. in the virtual token bus netowrk, the existing medium access control protocols hav ea switchove rtime overhead when traffic load is light or asymmetric according ot arbitration address of node that has message to send. The proposed protocol optimized average message delay using cyclic bus access chain to exclude switchover time of node that do not have message to send. Therefore it enhanced bus tuilization and average message delay that degrades the performance of real time communication netowrks. It showed that the proposed protocol is more enhacned than virtual token medium access control protocol and virtual token medium access control protocol iwth reservation through performance analysis.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.213-218
• /
• 2001

VR (Virtual reality) technologies have given engineers the ability to design, test, and evaluate engineering systems in a virtual environment. The virtual plant is the highlight of the application of the VR technology to plant engineering. Plant design, maintenance, control, management, operation are integrated in the virtual plant. The VR monitoring system including the concept of the virtual plant is developed to replace a current control room that has number of gages and warning lamps in two-dimensional panels which shows the operating status of a plant. The operating status of the plant is displayed in the VR monitoring system through the realistic computer graphics. Sophisticated, realistic and prompt control becomes possible. The VR monitoring system consists of advanced visualization, walk-through simulation and navigation. In the virtual environment, a user can navigate and interact with each component of a plant. In addition, the user can access the information by just clicking interesting component. The VR monitoring system is operated with various modules, such as (1) virtual plant constructed with Graphic Management System (GMS), (2) Touch & Tell System, and (3) Equipment DB System of Part. In order to confirm the usefulness of the VR monitoring system, a pilot gas plant which is currently being used for plant operator training is taken as application. The end of the paper gives an outlook on the future work and a brief conclusion.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.422-427
• /
• 2006

This paper presents force-feedback control performance of a haptic device in virtual environment of minimally invasive surgery(MIS). As a first step, based on an electrorheological(ER) fluid and spherical geometry, a new type of master device is developed and integrated with a virtual environment of MIS such as a surgical tool and human organ. The virtual object is then mathematically formulated by adopting the shape retaining chain linked(S-Chain) model. After evaluating reflection force, computational time, and compatibility with real time control, the virtual environment of MIS is formulated by interactivity with the ER haptic device in real space. Tracking control performances for virtual force trajectory are presented in time domain, and theirtrackingerrorsareevaluated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.12 s.117
• /
• pp.1286-1293
• /
• 2006

This paper presents force-feedback control performance of a haptic device in virtual environment of minimally invasive surgery(MIS). As a first step, based on an electrorheological (ER) fluid and spherical geometry, a new type of master device is developed and integrated with a virtual environment of MIS such as a surgical tool and human organ. The virtual object is then mathematically formulated by adopting the shape retaining chain linked(S-chain) model. After evaluating reflection force, computational time, and compatibility with real time control, the virtual environment of MIS is formulated by interactivity with the ER haptic device in real space. Tracking control performances for virtual force trajectory are presented in time domain.