• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.3
• /
• pp.48-56
• /
• 2002

The flow characteristics around KRISO 3600TEU container ship model have been experimentally investigated in a circulating water channel. The instantaneous velocity vectors were measured using 2-frame PIV measurement system. The mean velocity fields and turbulent statistics including turbulent kinetic energy and vorticity were obtained by ensemble-averaging 400 instantaneous velocity fields. The free stream velocity was fixed at 0.6m/s and the corresponding Reynolds number was $9{\times}10^5$. The test sections were divided into two regions, three transverse sections of the wake region(Station -0.5767, -1, -3) and five longitudinal sections of the wake((Z/(B/2)=0, 0.1, 0.2, 0.4, 0.6). In the wake region, large-scale longitudinal vortices of nearly same strength are symmetric with respect to the wake centerline and a relatively weak secondary vortex is formed near the waterline. With going downstream, the strength of longitudinal vortex is decreased and the wake region expands.

• Tribology and Lubricants
• /
• v.33 no.3
• /
• pp.85-91
• /
• 2017

This work studies the flow behaviors in the gap between the friction pad and separator in wet-clutch systems. The fluid volume of the lubricant is modeled using the entire system of wet-clutch pack of a dual clutch transmission that has larger outer radius of odd gear shifts and smaller inner radius of even gear shifts. Flow behaviors in the gap of the clutch pad are computed using the gear shift modes that consider the real relative velocities between the friction pad and separator. Flow behaviors in the gap of the disengaged clutch pad are mainly investigated for the wet-clutch system, whereas the engaged clutch pad is modeled with no fluid rate through the contacting surfaces. The developed hydrodynamic fluid pressures and velocity fields in the clutch pad gap are computed to obtain the relevant information for managing flow rates in wet-clutch packs under dual operating conditions during gear shifts. These hydrodynamic pressures and velocity fields are compared on the basis of each gear level and gap location, which is necessary to determine the effects of groove patterns on the friction pad. Shear stresses in the gap locations are also computed on the basis of the gear level for the inner and outer clutch pads. The computed results are compared and used for the design of cooling capacity against frictional heat generation in wet-clutch pack systems.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.11 no.4
• /
• pp.189-196
• /
• 1999

In order to verify a numerical model for the calculation of wave motion around an offshore barrier in shallow water, laboratory physical experiments are necessary. In this study, sample experiments are carried out on the wave and wave induced current fields due to a sloping bottom topography and on that due to an isolated structure from the coastline. The water body is divided into 4 levels, in which the current tracking floaters are deployed to measure the wave induced currents. Data measurement was continued using the limited wave gauges and current tracking floaters including a video camera from the top. The wave heights for the preselected surface and time-averaged velocity distributions at each level were measured in detail. The distribution of wave and current fields was analyzed precisely combining the whole measured laboratory data. Moreover, comprehensive analyses were carried out on non-linearity of wave transformation in terms of skewness and atiltness.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.4
• /
• pp.466-475
• /
• 2003

The gun-type gas burner adopted in this study is generally composed of eight slits and swirl vanes. Thus, this paper is studied to investigate the effect of slits and swirl vanes on the turbulent flow fields in the horizontal plane of gas swirl burner with a cone type baffle plate measured by using X-probe from hot-wire anemometer system. This experiment is carried out at flow rate 450 $\ell$/min in the test section of subsonic wind tunnel. The axial mean velocity component in the case of burner model with only swirl vanes shows the characteristic that spreads more remarkably toward the radial direction than axial one, it does, however, directly opposite tendency in the case of burner model with only slits. Consequently. both slits and swirl vanes composing of gun-type gas burner play an important role in decrease of the speed near slits and increase of the flow speed in the central part of a burner because the biggest speed spurted from slits encircles rotational flow by swirl vanes and it drives main flow toward the axial direction. Moreover, the turbulent intensities and turbulent kinetic energy of gun-type gas burner are distributed with a fairly bigger size within X/R<0.6410 than burner models which have only slits or swirl vanes because the rotational flow by swirl vanes and the fast jet flow by slits increase flow mixing, diffusion, and mean velocity gradient effectively.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.5
• /
• pp.493-500
• /
• 2001

The detection of axial cracks using conventional MFL pig is a significant challenge in the gas pipeline inspection. In this study, a technique using interaction of circumferentially induced torrents with axial stress corrosion crack is presented. The feasibility of this technique is investigated using finite element modeling. Finite element analysis of such interaction is a difficult problem in terms of both computation time and memory requirements. The challenges arise due to the nonlinearity of material properties, the small sire of tight cracks relative to that of the magnetizer, and also time stepping involved in modeling velocity effects. This paper presents an approach based on perturbation methods. The overall analysis procedure is divided into 4 simple steps that can be performed sequentially. Modeling results show that this technique can effectively detect colonies of SCC as well as single SCC.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1392-1399
• /
• 2001

The flow fields inside a molten Zn pot of continuous hot-chip galvanizing process were investigated experimentally. With varying several parameters including the strip speed Vs, flow rate Q of induction heater. scrapper location and baffle configuration, instantaneous velocity fields were measured using a PIV velocity field measurement technique. Inside the strip region, counter-clockwise rotating flow is dominant. The general flow pattern inside the strip region is nearly not influenced by the strip speed Vs, flow rate Q and the scrapper location. In the exit region, the flow separated from the moving strip due to the existence of a stabilizing roll ascends to the free surface, for the cases of no scrapper and scrapper detached form the roll. On the other hand, the ascending flow to the free surface is decreased, as the flow rate Q of induction heater increases. By installing a baffle around the uprising strip, the flow moving up to the stabilizing roll decreases. In addition, B-type baffle is better than A-type baffle in reducing speed of flow around the stabilizing rolls. However, the flow ascended to the free surface is largely influenced by changing the flow rate Q, and the scrapper location, irrespective of the baffle type.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.2
• /
• pp.171-181
• /
• 2002

Among various numerical methods of wave transformations including wave breaking by structure, models using VOF(Volume Of Fluid) method to trace free surface are getting into the spotlight recently. In order to analyze wave transformations and velocity of the wave fields due to the permeable submerged breakwater(PSB), This study applied VOF method to the two-dimensional wave channel installed line-source to generate waves and added dissipation zone to offer a non-reflective boundary. Hydraulic experiments was performed to obtain the application of two-dimensional numerical wave channel. The results of numerical experiments using the two-dimensional wave channel agree well with the experimental data. It was shown that vortices are formed behind the PSB, and in case of the 2-rowed PSB they also are occurred in between PSBs, strongly non-linear waves are developed on the crown of the PSB, and the direction of velocities in porous media is determined by the shape of free surface.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.1
• /
• pp.16-24
• /
• 2011

EFDC model was applied to reproduce velocity fields and to evaluate the dispersion characteristics of suspended sediments (SS) around a Daesan port. Numerical results using two-dimensional hydrodynamic model of EFDC showed good agreements through comparison with the time series and harmonic analysis of the tidal elevations. The dispersion patterns of the suspended sediments using the calculated velocity fields were calculated to move from east to northeast direction in flood tide and from west to southwest in ebb tide for dredging of sea route, respectively. Also, the suspended sediments were widely dispersed into the front areas of a Daesan port, Nanji-do and Garorim bay in the long-term. Therefore, it was inferred that the environmental problems for sea pollution would be occurred seriously if the dredging for sea route would be continued in the long-term.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1150-1157
• /
• 1988

Two-dimensional turbulent plane jet which is under the pressure gradient in the transverse direction is studied numerically. Full Navier-Stokes equations are used to correctly account for the pressure variation in the transverse direction. Using the standard k-.epsilon. turbulence model as a closure relationship, a time marching procedure gives the velocity field. The temperature fields are obtained for two different cases : (1) Hot jet is issued into the cold still air, and (2) Hot jet is issued into the surrounding across which exists a temperature difference. The velocity and temperature fields along with other flow and heat-transfer characteristics for two different pressure gradients are presented. A simple formula that relates the jet trajectory to the pressure gradient is also proposed. The mass flux in the longitudinal direction and the jet halfwidth seem insensitive to the pressure gradient. However, the pressure gradient increases the heat flux in the longitudinal direction as well as in the transverse direction.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.12
• /
• pp.991-997
• /
• 2014

This study investigated the swirling flow fields of a gun-type gas burner (GTGB) without a combustion chamber under cold flow conditions. Three velocity components and the static pressure were measured with a straight-type five-hole pressure probe (GHPP) using a non-nulling calibration method and compared with the results of an X-type hot-wire probe (X-probe) and computational fluid dynamics (CFD). The GHPP measured the velocity and static pressure for the swirling flow of the central region of the GTGB better than the X-probe but produced slightly worse results than the CFD.