• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.9 s.351
• /
• pp.32-39
• /
• 2006

5.8GHz DSRC(Dedicated Short Range Communications) is a short to medium range communications service that supports both public safety and private operations in roadside to vehicle and vehicle communication. However the 5.8GHz frequency may cause the shadowing effect or communication blocking problem when there is an obstacle or another vehicle between RSE (Road Side Equipment) and OBE (On Board Equipment). In this paper, to solve this problem of the 5.8GHz DSRC, we propose a relay protocol based on the standard of DSRC radio communication between RSE and OBE in the 5.8GHz band made by TTA (Telecommunication Technology Association). By using the proposed relay protocol to DSRC system and intervehicle communication, we also consider a fixed relay protocol and mobile relay protocol. We expect to apply this relay protocol for the DSRC intervehicle communication and video communication between drivers and safe distance among vehicles in the near future.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.37-45
• /
• 2018

An electric vehicle is an environmentally friendly vehicle because there is no exhaust gas, unlike gasoline automobiles. On the other hand, because the electric vehicle is driven by electric power charged in batteries, the distance to go through a single charge depends on the energy density of the batteries. Therefore, a lithium-ion battery with a high energy density is a good candidate for batteries in electric vehicles. Because the electrode is an essential component that governs the efficiency of a lithium-ion battery, the electrode manufacturing process plays a vital role in the entire production process of lithium-ion batteries. In particular, the drying process during the electrode manufacturing process is a critical process that has a significant influence on the performance. This paper proposes an innovative process for improving the efficiency and productivity of the drying process in electrode manufacturing and describe the equipment design method and development results. In particular, the design procedure and development method for enhancing the electrode adhesion power, atmospheric pressure superheated steam drying technology, and drying furnace slimming technologies are presented. As a result, high-speed drying technology was developed for battery electrodes through the world's first turbo dryer technology for mass production using open/integrated atmospheric pressure superheated steam. Compared to the conventional drying process, the drying furnace improved the productivity (Dry Lead Time $0.7min{\rightarrow}0.5min$).

• Journal of Korean Society of Transportation
• /
• v.20 no.6
• /
• pp.115-128
• /
• 2002

Traffic engineers have developed and implemented various microscopic simulation models to verify the traffic performance and to prevent the expected problems. The existing microscopic simulation models categorize drivers into several types to reflect various drivers' driving patterns but miss the dynamics of drivers' behavior changed based upon the traffic conditions. It was found from the field data collected from two different merging sections on an urban freeway in Seoul, Korea, that the drivers' critical gap distributions are changed based on (1) the traffic density on the adjacent lane to the acceleration lane and (2) the opportunities left to merge in terms of distance to the end of acceleration lane. It was also found from the study that the drivers' critical gap distributions follow the Normal distribution. and its mean and variance change while a vehicle progresses on an acceleration lane. This paper proposes a new gap-acceptance model developed based on a set of drivers' critical gap distributions from each segment on the acceleration lanes. Through the comparison study between the field data and the results from the simulation utilizing the proposed model, it was verified that (1) the distribution of merging points on an acceleration lane to the adjacent main lane at different density levels, (2) the size of the gap accepted for merging and (3) the speed difference between the merging vehicle and the trailing vehicle at the time of merging are statistically identical to the field data at 95% confidence level.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.46 no.2
• /
• pp.40-47
• /
• 2009

This paper proposes a method for vehicle license plate detection using mathematical morphology and symmetry. In general, the shape, color, size, and position of license plate are regulated by authorities for a better recognition by human. Among them, the relatively big intensity difference between the letter and the background region of the license plate and the symmetry about the plate are major discriminating factors for the detection. For the first, the opened image is subtracted from the closed image to intensify the region of plate using the rectangular structuring element which has the width of the distance between two characters. Second the subtraction image is average filtered with the mask size of the plate. Third, the column maximum graph of the average filtered image is acquired and the symmetry of the graph is measured at every position. Fourth, the peaks of the average filtered image are searched. Finally, the plate is assumed to be positioned around the one of local maxima nearest to the point of the highest symmetry. About 1,000 images taken by speed regulation camera are used for the experiment. The experimental result shows that the plate detection rate is about 93%.

• 전자공학회논문지 IE
• /
• v.44 no.1
• /
• pp.27-32
• /
• 2007

This study was to suggest the predictive model of propagation, considering the effect by the multipath waves produced by the sending and receiving vehicles' left/right reflectors and the adjacent vehicles when the communication between the vehicles on the one-way two-lanes road in the urban city with a lot of traffic jams. Then, the radius of curved road was 600[m], the length of curved roads $52.4\sim471.2[m]$, and the bridge's pier of road was $5o\sim45o$. Also, it was simulated by changing the receiving vehicle located on the curved road's gap from minimum 3.3[m] to maximum 29.5[m], corresponding to the change of distance of the bridge's pier of road and curved road. As a result of this research above, in case of $5o\sim15o$ bridge's pier of road, it was within l[dB] regardless of the receiving vehicle's position on the curved road in case of propagation path loss. In case of $15o\sim45o$, it was approximately $1\sim8[dB]$ as the bridge's pier of road is changed. And, in case of propagation path, it found out that it was changed to $0.4\sim120[m]$ according to the change of bridge's pier of road. Then, the delay time of propagation was 400[nsec] as it produced 120[m] in the difference of propagation path.

• Journal of Advanced Navigation Technology
• /
• v.24 no.4
• /
• pp.245-250
• /
• 2020

Currently, unmanned military vehicles under development in Korea have more devices to carry out various missions, and interface cables between them are also increasing. In addition, due to a small space problem inside the unmanned vehicle, devices are required to be miniaturized and integrated. For two reasons, connectors also need to be selected, which makes them vulnerable to noise due to the closer distance between the pins. In this paper, we analyzed how much the magnetic field produced by noise at the connector pin where cable twist is released affects the surrounding pin and presented the guide for optimal pin placement. First, the effect of magnetic field is greater than the crosstalk between pin and pin. Second, the magnetic field on both sides between + and - is strong when approaching one step with noise source. Third, the magnetic field strength is improved when setting the ground pin as the ground pin between the noise and the original signal when approaching the A noise source and the two steps. Fourth, in the case of a differential mode communication, the optimal placement area of the sensitive signal was presented according to positions Tx± and Rx±.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.1
• /
• pp.47-60
• /
• 2021

Hydrogen is a next-generation energy source, and according to the roadmap for activating the hydrogen economy, it is expected that industries to stably produce, store, and transport of hydrogen as well as the supply of hydrogen fuel cell vehicles will be made rapidly. Accordingly, safety measures for accidents of hydrogen vehicles in confined spaces such as tunnels are required. In this study, as part of a study to ensure the safety of hydrogen fuel cell vehicles in road tunnels, a basic investigation and research on the risk of fire and explosion due to gas leakage and hydrogen tank rupture among various hazards caused by hydrogen fuel cell vehicle accidents in tunnels was conducted. The following results were obtained. In the event of hydrogen fuel cell vehicle accidents, the gas release rate depends on the orifice diameter of TPRD, and when the gas is ignited, the maximum heat release rate reaches 3.22~51.36 MW (orifice diameter: 1~4 mm) depending on the orifice diameter but the duration times are short. Therefore, it was analyzed that there was little increase in risk due to fire. As the overpressure of the gas explosion was calculated by the equivalent TNT method, in the case of yield of VCE of 0.2 is applied, the safety threshold distance is analyzed to be about 35 m, and number of the equivalent fatalities are conservatively predicted to reach tens of people.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.77-86
• /
• 2020

Power quality problems caused by feeder voltage drop and extension construction cost problems can occur with the increasing utilization rates of the existing fixed-type EV (electric vehicle) charger. Moreover, EV users might not be able to access the EV charger due to a lack of EV charging facilities. Therefore, this paper proposes an MPSD (movable power supply device) for EVs to overcome user inconvenience caused by the insufficient number of chargers and extension cost issues. The proposed MPSD was mainly composed of a PV (photovoltaic) system, ESS (energy storage system), EV charging system, and monitoring and control system. Furthermore, there are three operation modes available to enhance the flexibility of the MPSD application, depending on the situation. This paper also presents an economical evaluation modeling using the present worth method to consider the cost and benefit elements. The simulation results based on proposed modeling showed that MPSD is more economical than the existing EV charger. Moreover, its profit can be increased significantly depending on the distance to the installation point.

• Journal of Broadcast Engineering
• /
• v.27 no.6
• /
• pp.936-939
• /
• 2022

As air combat system technologies developed in recent years, the development of air defense systems is required. In the operating concept of the anti-aircraft defense system, selecting an appropriate armament for the target is one of the system's capabilities in efficiently responding to threats using limited anti-aircraft power. Much of the flying threat identification relies on the operator's visual identification. However, there are many limitations in visually discriminating a flying object maneuvering high speed from a distance. In addition, as the demand for unmanned and intelligent weapon systems on the modern battlefield increases, it is essential to develop a technology that automatically identifies and classifies the aircraft instead of the operator's visual identification. Although some examples of weapon system identification with deep learning-based models by collecting video data for tanks and warships have been presented, aerial vehicle identification is still lacking. Therefore, in this paper, we present a model for classifying fighters, helicopters, and drones using a convolutional neural network model and analyze the performance of the presented model.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.5D
• /
• pp.443-451
• /
• 2010

This paper proposes the methodology about advisory safety speed based on real-time vehicular data collected from highway. The proposed model is useful information to drivers by appling seamless wireless communication and being collected from ECU(Engine Control Unit) equipment in every vehicle. Furthermore, this model also permits the use of realtime sensing data like as adverse weather and road-surface data. Here, the advisory safety speed is defined "the safety speed for drivers considering the time-dependent traffic condition and road-surface state parameter at uniform section", and the advisory safety speed model is developed by considering the parameters: inter-vehicles safe stopping distance, statistical vehicle speed, and real-time road-surface data. This model is evaluated by using the simulation technique for exploring the relationships between advisory safety speed and the dependent parameters like as traffic parameters(smooth condition and traffic jam), incident parameters(no-accident and accident) and road-surface parameters(dry, wet, snow). A simulation's results based on 12 scenarios show significant relationships and trends between 3 parameters and advisory safety speed. This model suggests that the advisory safety speed has more higher than average travel speed and is changeable by changing real-time incident states and road-surface states. The purpose of the research is to prove the new safety related services which are applicable in SMART Highway as traffic and IT convergence technology.