• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.325-331
• /
• 2013

In this study, a complex eigenvalue analysis is implemented to verify the unstable mode of a brake system using ABAQUS software. The component participation factors and component modal participation factors are used to analyze the total contributions from each component and each component mode to a particular unstable system mode. This study shows that the 1.4-kHz unstable system mode comes from mode coupling between the 2nd nodal diametric mode and 3rd lateral axial mode (LAM) in the baseline model. A sensitivity analysis with a linking index is performed to prevent the mode coupling of the component modes. This linking index analysis shows the optimum mass loading position to move away the natural frequency of the 3rd LAM, which contributes to the unstable mode. Finally, a complex eigenvalue analysis is implemented with mass loading in the tie bar position, and no unstable system mode is generated in the low-frequency range (below 2 kHz).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.12
• /
• pp.7292-7301
• /
• 2014

With the development of IT Info-Communications technology, the vehicle with a combination of wireless-communication technology has resulted in significant research into the convergence of the component of existing traffic with information, electronics and communication technology. Intelligent Vehicle Communication is a Machine-to-Machine (M2M) concept of the Vehicle-to-Vehicle. The Vehicle-to-Infrastructure communication consists of safety and the ease of transportation. Security technologies must precede the effective Intelligent Vehicle Communication Structure, unlike the existing internet environment, where high-speed vehicle communication is with the security threats of a wireless communication environment and can receive unusual vehicle messages. In this paper, the Vehicle Identification number between the V2I and the secure message communication protocol was proposed using hash functions and a time stamp, and the validity of the vehicle was assessed. The proposed system was the performance evaluation section compared to the conventional technique at a rate VPKI aspect showed an approximate 44% reduction. The safety, including authentication, confidentiality, and privacy threats, were analyzed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.379-381
• /
• 2009

In designing full vehicle, crash safety, fuel efficiency, exhaust gas, and driving stability are very important factors. Especially, automotive wheel which supports total vehicle weight is a critical component in view of driving stability. Most of automotive wheel have been manufactured for beautiful appearance by using aluminum alloy in domestic industry. However, the amount of automotive steel wheel used are on an increasing trend according to developing the advanced high strength steel with good formability property recently. In this study, the circumferential deviation of rim with various thickness and yield strength was investigated. The formability evaluation of the rim was developed by using a finite element module furnished by Forge software.

• Journal of Institute of Convergence Technology
• /
• v.3 no.1
• /
• pp.19-23
• /
• 2013

This study is concerned with air-conditioning system in use of thermoelectric device. It is introduced that the well designed structures for better cooling & heating performance with high efficiency. And also it is performed that the system performance test of four types trial products for the use of hybrid commercial vehicle. System performance is affected by many component parts, especially heat sink design & power control method. It is applied that dual extrusive fin tube with buffer zone for the effective radiating of circulating liquid in tube. And also it is applied that power supply method with constant-current system. It is attained that system cooling capacity is 1.2kW, COP is 0.95.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.465-470
• /
• 1999

This paper presents a design method of driving system for EV(Electric Vehicle). EV driving system consist of batteries, battery interface system and inverter. The power control circuit of the driving system is simple, since only one PWM(Pulse Width Modulation) inverter is used. These test spectrums and waveforms can be used to determine the filter component ratings as well as to compute the harmonics injected into the source. The hybrid control strategy which can reduced harmonic components. The analysis results indicate that the required capacity of the condenser can be reduced with LC filter. In this paper, the design and implementation of the proposed systems are described and some experimental results are given to show the performance of this driving system. The control strategy of the system to available inverter's power and motor's power and torque is discussed.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.44-53
• /
• 1992

Automotive transmission is the principle component of vehicle driving system, which transmits the adjusted engine power. The automation of transmission arises from the annoyance of transmission operation such as the frequent stop/start of vehicle and the shifting transients. The study on the optimal shifting condition for the automation of transmission needs the investigation of shifting transients. However, the dynamic modeling theory during transient period is not well-established. In this study, the techniques of dynamic modeling for the power transmission system with Merrite-Wilson gear train are presented. To predict the shifting transients, a driving simulation program is developed, and the results of the analysis are cross-checked in the field test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.48-55
• /
• 2007

A bushing component of a vehicle suspension system is tested to capture the nonlinear behavior of rubber bushing element using the MTS 3-axes rubber test machine. The results of the tests are used to model the artificial neural network bushing model. The performances from the neural network model usually are dependent on the structure of the neural network. In this paper, maximum error, peak error, root mean square error, and error-to-signal ratio are employed to evaluate the performances of the neural network bushing model. A simple simulation is carried out to show the usefulness of the developed procedure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.201-208
• /
• 2013

Recently, there has been an active study about weight reduction for automotive. This study is prediction and evaluation of one pice type steering component, which is universial joint. Steering system is a core of major safe device in vehicle. Universial shaft adopted in steering system transmit steering torque between olumn and steering gear. Conventional universial shaft is produced by welding process because of geometric complexity. But welding process has some weakness such as deflection on surface, residual stress, and deteronration of material properties so it can deteriorate durability of vehicle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2002.04a
• /
• pp.10-13
• /
• 2002

Pogo is the instability resulting from the interaction between rocket structure and propulsion system of liquid propellant rocket. The coupling of structure and propulsion system can lead to severe problem in rocket. For the analysis of pogo, a time-invariant linearized mathematical model is developed for a selected flight time. Propulsion system is modeled using element representations for each components. The constitutive equation of propulsion system is a homogeneous second-order equation form in the Laplace domain. Rocket structure is modeled using FEM. From the results of modal analysis of structure, the behavior of structure can be represented. System equations for coupling structure and propulsion system are composed of all propulsion system equations and vehicle motion equations reacting on the vehicle by each component of propulsion system. The stability is obtained by the eigen solution of system matrix. The optimization of the design variables such as size, place of accumulator for suppressing pogo instability is carried out. This article of study can be used to determine the degree of stability, and guide the design of pogo suppression system.

• Journal of Auto-vehicle Safety Association
• /
• v.4 no.1
• /
• pp.5-11
• /
• 2012

This paper discusses the evaluation of the safety impact of the Adaptive Cruise Control (ACC) system in Korea. To evaluate the safety impact, this paper suggests an analysis method by using the test scenario and field operational test data. The test scenario is composed to represent the main component factor of the ACC system and ACC related accident situation such as rear-end collision, lane-change, and road-curvature, etc. Also, from the field operation test data, the system's potential to increase the safety can be measured ideally. Besides, field operational testdata was used to revise the expected safety impact value as Korean road conditions. By using the proposed evaluation method, enhanced safety impact of the ACC system can be estimated scientifically.