• Journal of the Korean Ceramic Society
• /
• v.27 no.5
• /
• pp.583-588
• /
• 1990

Glass films in the binary system B2O3-SiO2 and Al2O3-SiO2 were prepared on soda-lime-silica slide glass by the dip-coating technique from TEOS and boric acid or aluminum nitrate. Thickness of the films varying with viscosity and withdrawal speed were measured and effect of composition and firing temperature on the properties such as transmittance and refractive index were investigated. nM2O3.(100-n)SiO2(M=B or Al) films containing up to 20mol% B2O3 and 40mol% Al2O3 were transparent. Maximum transmittance at visible range were obtained for the sample containing 15mol% Ba2O3 and 32.5mol% Al2O3 and heat-treated at 50$0^{\circ}C$, respectively. Refractive index of the film containing 15mol% B2O3 was mininum in the B2O3-SiO2 binary system and minimal refractive index was appeared at the film containing 32.5mol% Al2O3. In IP spectra, addition of B2O3 were increased absorption peak intensity of B-O and Si-O-B bond and addition of Al2O3 were decreased absorption peak intensity of Si-O bond, respectively.

• Journal of the Korean Society of Safety
• /
• v.20 no.4 s.72
• /
• pp.20-28
• /
• 2005

In this paper, the methodology for the reliability estimation of buried pipeline with longitudinal gouges and dent is presented and the limit state of buried pipeline is formulated by failure assessment diagram(FAD). The reliability of buried pipeline with defects has been estimated by using a theory of failure probability. The failure probability is calculated by using the FORM(first order reliability method) and Monte Carlo simulation. The results out of two procedures have been compared each other. It is found that the FORM and Monte Carlo simulation give similar results for varying boundary conditions and various random variables. Furthermore, it is also recognized that the failure probability increases with increasing of dent depth, gouge depth, gouge length, operating pressure, pipe outside radius and decreasing the wall thickness. And it is found that the analysis by using the failure assessment diagram gives highly conservative results than those by using the theory of failure probability.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.46-48
• /
• 2004

A micro-scale discharge device has been fabricated using MEMS technology and failure mechanisms during DC discharge are investigated for the microstructure. The failure of sustaining the plasma is mainly caused by either open or short of the micro-electrodes, both resulting from the sputtered metal atoms during the DC discharge. The glow discharge lifetime of the microstructures is found to depend on bias circuit scheme as well as the electrode structure. Based on the understanding of the failure mechanism, a novel microstructure is suggested to improve discharge lifetime and the longer lifetime is experimentally demonstrated. In addition to the failure mechanism, an electric breakdown between two electrodes with microns gap are studied using micromachined metal structures. The electrode gap is able to be accurately controlled by thickness of a sacrificial layer and the electric breakdown was measured while varying the gap from $2{\mu}m$ to $20{\mu}m$. The electric breakdown behavior was found to highly depend on the electrode material, which was not considered in Paschen's law.

• Journal of the Korean Society of Combustion
• /
• v.10 no.4
• /
• pp.33-40
• /
• 2005

The propagation rates of advancing and retreating non-premixed edge flames in a slot-jet counterflow were measured as a function of strain rate for varying jet spacing, mixture strength, stoichiometric mixture fractions $(Z_{st})$ and Lewis numbers (Le). Methane and propane fuels were tested and nitrogen and carbon dioxide were used as inerts. As results, we could identify igniting fronts, retreating fronts, two total extinction limits, and short-length edge flames. A burner separation affected to a low extinction limit only. Regimes for advancing and retreating edges together with total extinction were mapped in terms of normalized flame thickness and heat loss factor for $CH_4/O_2/N_2$ mixtures. Edge flames for $Z_{st}$ > 0.5 behaved like a stronger mixture while for $Z_{st}$ < 0.5 showed deteriorated feature, because of relative locations of a non-premixed flame and intermediate species such as CO and $H_2$. Furthermore, due to the relative importance of heat loss, propagating speeds of edge flames were significantly enhanced in $CH_4/O_2/CO_2$ mixtures (Le < 1) demonstrating increasing stability limits. However $C_3H_8/O_2/N_2$ mixtures (Le > 1) showed opposite result.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.531-532
• /
• 2005

We have used ITO/$Alq_3$/Al structure to study electrical conduction mechanism in $Alq_3$ based organic light emitting diode. Current-voltage characteristics were measured at room temperature by varying the thickness of $Alq_3$ layer from 60 to 400nm. We were able to prove that there are three different mechanism depending on the applied voltage; Ohmic, SCLC (space-charge-limited current). and TCLC (trap-charge -limited current) mechanism.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.438-439
• /
• 2006

We have used ITO/$Alq_3$/Al structure to study complex impedance in $Alq_3$ based organic light emitting diode. Equivalent circuit was analyzed in a device structure of ITO/$Alq_3$/Al by varying the thickness of $Alq_3$ layer from 60 to 400nm. The impedance results can be fitted using equivalent circuit model of parallel combination resistance $R_p$ and capacitance $C_p$ with a small series resistance $R_s$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.439-440
• /
• 2007

To enhance the electron injection from the cathode of organic light-emitting diodes (OLEDs), We have studied characteristics of device that electron injection layer(EIL) is inserted between emissive layer and cathode. We fabricated bi-layer cathode $Li_2O$(x nm)/Al(100nm) and LiF(x nm)/Al(100nm) using LiF and $Li_2O$ as an electron injection layer. We analyzed the current efficiency, luminance efficiency, and external quantum efficiency of the device by varying the thickness of $Li_2O$ and LiF to be 0.5nm, 1nm, or 3nm. Using the EIL, we have obtained the efficiency of 7cd/A and the luminance of $20,000cd/m^2$. There is an improvement of efficiency by more than 3 times than the device without the $Li_2O$ layer.

• Journal of Welding and Joining
• /
• v.25 no.6
• /
• pp.59-63
• /
• 2007

The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates and in addition internal and external constraints have much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to butt weld of thin plates to reduce the transverse and longitudinal deformation. In order to investigate the quantitative effect of tensioning method upon the reduction of angular deformation and shrinkage in longitudinal and transverse direction of weld line, butt welding test has been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. From the present experimental study, it has been found that the tensioning method is very effective in reducing the weld-induced residual stress as well as the weld-induced deformation.

• Journal of Mechanical Science and Technology
• /
• v.19 no.6
• /
• pp.1280-1289
• /
• 2005

This paper presents the effects of corrosion environments of failure pressure model for buried pipelines on failure prediction by using a failure probability. The FORM (first order reliability method) is used in order to estimate the failure probability in the buried pipelines with corrosion defects. The effects of varying distribution types of random variables such as normal, lognormal and Weibull distributions on the failure probability of buried pipelines are systematically investigated. It is found that the failure probability for the MB31G model is larger than that for the B31G model. And the failure probability is estimated as the largest for the Weibull distribution and the smallest for the normal distribution. The effect of data scattering in corrosion environments on failure probability is also investigated and it is recognized that the scattering of wall thickness and yield strength of pipeline affects the failure probability significantly. The normalized margin is defined and estimated. Furthermore, the normalized margin is used to predict the failure probability using the fitting lines between failure probability and normalized margin.

• Journal of Korea Multimedia Society
• /
• v.6 no.2
• /
• pp.325-331
• /
• 2003

In this paper, we designed a spiral inductor and voltage controlled oscillator with the negative resistor for the bluetooth receiver by using 0.25$\mu\textrm{m}$ 1-poly 5-metal CMOS n-well process. The proposed inductor, which applies multi layer metal structure, is a structure that decreases resistance value by increasing he metal thickness. As the resistance value decreases, the quality factor Q has improved. Also, voltage-controlled oscillator is designed applying 1 port negative resistance, and changes its oscillating frequency by varying outside capacitor values. The simulation results show that oscillating frequency is 2.33~2.58GHz changing from 2pF to 14pF, and the oscillator has oscillating power over 0dBm.