• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.369-374
• /
• 2011

Usually, a LPF (low pass filter) is used in the feedback loop of a SRF (synchronous reference frame) - PLL (phase locked loop) system because the measured grid voltage contains harmonic distortions and sensor noises. In this paper, it is shown that the cut-off frequency of the LPF should be designed to suppress the harmonic ripples contained in the measured voltage. Also, a new design method for the loop gain of the PI-type controller in the SRF-PLL is proposed with consideration of the dynamics of the LPF. As a result, a better transient response can be obtained with the proposed design method. The LPF frequency and the PI controller gain are designed in coordination according to the steady state and dynamic performance requirements. Furthermore, in the proposed method, the controller gain and the LPF cut-off frequency are changed from their normal value to a transient value when a voltage disturbance is detected. This paper shows the feasibility and usefulness of the proposed methods through the computer simulations and experimental results.

• Journal of IKEEE
• /
• v.13 no.1
• /
• pp.41-48
• /
• 2009

This paper describes an implementation of the analog front end (AFE) incorporated with the image signal processing (ISP) unit in the SoC, dominating the performance of the CCD image sensor system. New schemes are exploited in the high-frequency sampling to reduce the sampling uncertainty apparently as the frequency increases, in the structure for the wide-range variable gain amplifier (VGA) capable of $0{\sim}36\;dB$ exponential gain control to meet the needed bandwidth and accuracy by adopting a new parasitic insensitive capacitor array. Moreover, the double cancellation of the black-level noise was efficiently achieved both in the analog and the digital domain. The proposed topology fabricated in a $0.35-{\mu}m$ CMOS process was proved in a full CCD camera system of 10-bit accuracy, dissipating 80 mA at 15 MHz with a 3.3 V supply voltage.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.1
• /
• pp.45-51
• /
• 2009

A low-voltage, low-power analog CMOS front-end for a cardiac pacemaker is proposed. The circuits include a 4th order switched-capacitor (SC) filter with a passband of 80-120 Hz and a SC variable gain amplifier whose control range is from 0 to 24-dB with 0.094 dB step. An inverter-based switched-capacitor circuit technique is used for low-voltage operation and ultra-low power consumption, and correlated double sampling technique is used for reducing the finite gain effect of an inverter. The proposed circuit has been designed in a $0.35-{\mu}m$ CMOS process, and it achieves 80-dB SFDR at 5-kHz sampling frequency. The power consumption is only 330 nW at 1-V power supply.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.6
• /
• pp.602-611
• /
• 2004

Servo system has commonly adapted PI controller with fixed gains, because of its simplicity and determinative relationship among the parameters. The fixed gains PI system may be applied well to some operation conditions, but not non-linearities, complex and time variant operation conditions. For solving these problems, another conventional method, 'variable gun schedule according to speed', is published. The value of gain is determined according to the absolute value of the mover real speed. In this paper, FSTPIC(Fuzzy Self-Tuning PI Controller) is proposed based on various experiences to rapidly reduce speed error and to secure a good speed response characteristics. The effectiveness of proposed algorithms is demonstrated by comparing to two conventional gain systems via 4-quadrant operation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.12
• /
• pp.68-74
• /
• 2010

A sub-${\mu}$W CMOS Wien-Bridge oscillator for ultra low power (ULP) radio applications is presented. The Wien-Bridge oscillator is based on an non-inverting opamp amplifier with a closed-loop gain $1+R_2/R_1$ as a means of providing necessary loop gain. An additional RC network provides appropriate phase shift for satisfying the Barkhausen oscillation condition at the given frequency of 1/($2{\pi}RC$). In this design, we propose a novel loop gain control method based on a variable capacitor network instead of a rather conventional variable resistor network. Implemented in $0.18{\mu}m$ CMOS, the oscillator consumes only 560 nA at the oscillation frequency of 22 kHz.

• The Journal of Engineering Research
• /
• v.2 no.1
• /
• pp.57-62
• /
• 1997

Two psychoacoustic models used in MPEG-1 employ different masking patterns, different masking indexes, and different computational procedures. As a result, Model 1 is inferior to Model 2 due to its worst case approach in computing the SMR even though it determines tonality and masking levels accurately. In this study, we investigate the performances of psychoacoustic models when we modify the MPEG-1 audio coder for variable bitrates. Simulation results show that Model 2 has a gain of 30 kbps in the dual channel mode and 20 kbps in the joint stereo mode. It is generally known that the joint stereo mode has a gain in bitrate compare to the dual channel mode. For signals with frequent attacks, this gain becomes larger in Model 1 than in Model 2. This is due to the fact that Model 1 uses the worst case approach in computing the SMR to reduce pre-echo

• Journal of the Korean Solar Energy Society
• /
• v.39 no.6
• /
• pp.83-91
• /
• 2019

Photovoltaic thermal (PVT) collectors are devices that simultaneously produce electricity and heat. Research on conventional air-type PVT collector focuses on installing baffles to enhance the collector's thermal performance. However, the baffles have pressure drop inside the collector which degrades the thermal performance. Thus, it is necessary to design baffles to smoothen the flow inside the air-type PVT collector. Alternatively, installing perforated baffles in air-type PVT collectors can reduce the collector weight, but parameters such as the diameter of the perforated holes and the height of the perforated plates should be considered. Therefore, the main aim of this study was to analyze thermal characteristics of each variable of perforated baffles installed inside air-type PVT collector. For this purpose, the uniformity of air flow in the collector was compared through NX program, and the resultant heat gain and thermal efficiency of the air-type PVT collector were compared and analyzed. Therefore, the main aim of this study was to analyze thermal characteristics of each variable (Baffle angle, length, height, pitch, perforated ratio) of perforated baffles installed inside air-type PVT collector. For this purpose, the uniformity of air flow in the collector was compared through CFD program, and the resultant heat gain and thermal efficiency of the air-type PVT collector were compared and analyzed. As a result, the maximum outlet temperature was increased by 1.45 times and the heat gain was increased by 193.8 Wth, depending on the perforated baffle plate, compared to the collector without the baffle. The heat transfer performance showed that the maximum internal velocity was 1.61 times higher and the Reynolds number was 1.06 times higher depending on the parameters of the baffle plate.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.299-302
• /
• 2016

In this paper, we designed the stack monitoring system with improved performance. To block the incoming pulse noise to the amplifier, shield and the power supply impedance are reduced and the power circuit is isolated. The control unit is developed with variable high voltage, adaptive gain, offset and threshold in order to match the scintillation detector characteristic to the apparatus. 300-1500V variable high voltage power circuit is configured applicable to various scintillation detector. Stack monitoring system with improved performance guarantee the efficiency and the reliability by considering the characteristic of various scintillation detector. Developed stack monitoring system is evaluated with certified testing equipment and shows excellent performance with respect to the uncertainty of the sensor test results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.6C
• /
• pp.462-468
• /
• 2012

In this paper, an adaptive digital automatic gain control(AGC) algorithm with two stages is proposed. AGC technique is crucial for mobile communication equipment because path loss in wireless channel and gain fluctuation in receiver front-end continuously change the received signal strength. Furthermore, adaptive criteria should be applied to the design of AGC algorithm in order to support many waveforms with one SDR communication device. With these reasons, a two-stage structure is proposed to satisfy both flexibility and adaptiveness. Compared with conventional method, it also requires shorter convergence time. Numerical results show that the gain value of variable gain amplifier(VGA) is converged within proper time and proposed scheme controls the input level of analog to digital converter(ADC) to be stable during long range of time.

• Korean Management Science Review
• /
• v.23 no.2
• /
• pp.1-16
• /
• 2006

With the diffusion of the Internet, firms try to electronically collaborate with their partners in order to cut costs and gain profits. This, electronic Partnership, called 'Collaborative IT' is quite popular between large purchase enterprises and small-to-medium sized sub-contractors. This study investigates such relations. This study proposes three groups of research variables-interorganizational relationship, collaborative IT activity, and firm performance. the interorganizational relationship consists of trust, commitment, and asymmetry of commitment. Collaborative IT activity is composed of information sharing and workflow integration. The ultimate dependent variable is firm performance. It is hypothesized that the relationship factors influence the level of collaborative IT activity, while the latter in turn affects the firm performance. The relationship factors nay also directly affect the dependent variable. In addition, collaborative IT motive, as a moderating variable, may influence the causal relationship. By means of survey, ore hundred and eighty-two responses were obtained. Most sample companies are small-sized, in the manufacturing sector. The analysis of data reveals that both trust and commitment positively affects the level of collaborative IT activity, while asymmetry of commitment has negative effects. The workflow integration is significantly related with firm performance. Information sharing, however, has no signific3nt effects. Furthermore, asymmetry of commitment shows reverse relationship with firm performance. Collaborative IT motive works as a moderating variable between information sharing and firm performance. Finally, workflow integration is believed to mediate between relationship factors and firm performance.